Add address_little_endian for epaper displays with little endian
(low byte first) addresses.
Also clears allocated display and display bus memory so it has a
known state. The acep member wasn't always set so it varied
accidentally.
Fixes#7560. May fix#7778. Fixes#5119.
PicoDVI in CP support 640x480 and 800x480 on Feather DVI, Pico and
Pico W. 1 and 2 bit grayscale are full resolution. 8 and 16 bit
color are half resolution.
Memory layout is modified to give the top most 4k of ram to the
second core. Its MPU is used to prevent flash access after startup.
The port saved word is moved to a watchdog scratch register so that
it doesn't get overwritten by other things in RAM.
Right align status bar and scroll area. This normally gives a few
pixels of padding on the left hand side and improves the odds it is
readable in a case. Fixes#7562
Fixes c stack checking. The length was correct but the top was being
set to the current stack pointer instead of the correct top.
Fixes#7643
This makes Bitmap subscr raise IndexError instead of ValueError
when the index arguments are wrong.
It now handles deinit, never_reset and sharing tracking. PWM
now runs in the WAIT state as well during a time.sleep().
_reset_ok() was removed because it was called in one spot right
before deinit().
Some PWMOut were also switched to a bitmap for use instead of
reference count. That way init and deinit are idempotent.
Fixes#6589. Fixes#4841. Fixes#4541.
This 2-in-1 PR started with the goal of support the Bangle.js 2
smartwatch with *no USB*.
* Adds "secure" DFU build support with a committed private key.
* Adds 3-bit color support with one dummy bit for the JDI memory display
* Allows nrf boards to have a board_background_task() run in RUN_BACKGROUND_TASK.
This is needed because the Bangle.js 2 uses the watchdog to reset.
* Renamed port_background_task() to port_background_tick() to indicate it
runs on tick, not RUN_BACKGROUND_TASK.
* Marks serial connected when the display terminal is inited. This means
that safe mode messages show up on the display.
ACep, 7-color epaper displays also pack 3 bits in 4. So, I added that
support as well.
* Adds 3-bit ACeP color support for 7-color e-paper displays. (Not
watch related but similar due to color depth.)
* Allows a refresh sequence instead of a single int command. The 7" ACeP
display requires a data byte for refresh.
* Adds optional delay after resetting the display. The ACeP displays
need this. (Probably to load LUTs from flash.)
* Adds a cleaning phase for ACeP displays before the real refresh.
For both:
* Add dither support to Palette.
* Palette no longer converts colors when set. Instead, it caches
converted colors at each index.
* ColorConverter now caches the last converted color. It should make
conversions faster for repeated colors (not dithering.)
(1 << 32), an operation on a signed 32-bit int, is undefined in C. The
operation on the unsigned int (1u<<32) is defined as zero, which is
the desired outcome (subtracting 1 yields the value with all bits set)
This problem was detected by clang scan-build static analysis
This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
