As the new default behaviour, this allows PyDFU to be used with all
devices, not just the ones matching a specific set of VID/PID values. But
it's still possible to specify VID/PID if needed to narrow down the
selection of the USB device.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
Leaving the bootloader from an IRQ (eg USB or I2C IRQ) will not work if
MBOOT_LEAVE_BOOTLOADER_VIA_RESET is disabled, ie if mboot jumps directly to
the application. This is because the CPU will still be in IRQ state when
the application starts and IRQs of lower priority will be blocked.
Fix this by setting a flag when the bootloader should finish, and exit the
bootloader always from the main (top level) thread.
This also improves the USB behaviour of mboot: it no longer abruptly
disconnects when the manifest command is sent.
Signed-off-by: Damien George <damien@micropython.org>
RX and CTS are the input pins and pull-ups are enabled so they don't cause
a problem if left unconnected. But the output pins don't need a pull up
(they were originally all configured with pull up in commit
8f7491a109).
If needed, the pull-ups can be disabled in Python using machine.Pin after
the UART is constructed.
See issue #4369.
Signed-off-by: Damien George <damien@micropython.org>
The DMA driver will turn off DMA if it hasn't been used for an amount of
time (to save power). The SDIO driver for cyw43 WLAN was not informing the
DMA driver that it was using DMA and there was a chance that the DMA would
turn off in the middle of an SDIO DMA transfer. The symptoms of this would
be printing of SDIO error messages and a failure to communicate with the
cyw43 WLAN module.
This commit fixes this issue by changing the SDIO driver to use the
dma_nohal_XXX API to initialise and start the DMA.
Signed-off-by: Damien George <damien@micropython.org>
This can be treated by the linker the same as R_X86_64_REX_GOTPCRELX,
according to https://reviews.llvm.org/D18301.
Signed-off-by: Damien George <damien@micropython.org>
SysTick cannot wake the CPU from WFI/WFE so a hardware timer is needed to
keep track of ticks/delay (similar to the nrf port).
Fixes issue #7234.
Signed-off-by: Damien George <damien@micropython.org>
The proper way to do this is to test for __APPLE__ and __MACH__, where
__APPLE__ tests for an Apple OS and __MACH__ tests that it is based on CMU
Mach. Using both tests ensures that just Darwin (Apple's open source base
for MacOS, iOS, etc.) is recognized. __APPLE__ by itself will test for any
Apple OS, which can include older OS 7-9 and any future Apple OS. __MACH__
tests for any OS based on CMU Mach, including Darwin and GNU Hurd.
Fixes#7232.
MicroPython does not store any reference from a function object to the
module it was defined in, but there is a way to use function.__globals__ to
indirectly get the module.
See issue #7259.
Signed-off-by: Damien George <damien@micropython.org>
This significantly reduces the time taken to run the test suite (on the
unix port). Use `-j1` to disable this feature.
Signed-off-by: Jeff Epler <jepler@gmail.com>
Array equality is defined as each element being equal but to keep
code size down MicroPython implements a binary comparison. This
can only be used correctly for elements with the same binary layout
though so turn it into an NotImplementedError when comparing types
for which the binary comparison yielded incorrect results: types
with different sizes, and floating point numbers because nan != nan.
A board can now customise mboot with:
- MBOOT_LED1, MBOOT_LED2, MBOOT_LED3, MBOOT_LED4: if it needs to have
different LEDs for mboot compared to the application
- MBOOT_BOARD_LED_INIT: if it needs a fully customised LED init function
- MBOOT_BOARD_LED_STATE: if it needs a fully customised LED state-setting
function
- MBOOT_BOARD_GET_RESET_MODE: if it needs a fully customised function to
get the reset mode
With full customisation, the only requirement is a single LED to show the
status of the bootloader (idle, erasing, flashing, etc), which can be
configured to do nothing if needed.
Signed-off-by: Damien George <damien@micropython.org>
It is enabled by default to get the standard behaviour of doing a reset
after it is finished, but can be disabled by a board to jump straight to
the application (likely the board needs to use MBOOT_BOARD_CLEANUP to make
this work).
The application is passed a reset mode of BOARDCTRL_RESET_MODE_BOOTLOADER
if the bootloader was active and entered via a jump.
Signed-off-by: Damien George <damien@micropython.org>
This new logic is equivalent to the old logic when the only possibilities
for reset_mode are NORMAL, SAFE_MODE and FILESYSTEM, which is the standard
case. But the new logic also allows other reset_mode values (eg
BOOTLOADER) to run boot.py and main.py.
Signed-off-by: Damien George <damien@micropython.org>
When disabled the bootloader is entered via a direct jump. When enabled
the bootloader is entered via a system reset then a jump. It's enabled by
default to retain the existing behaviour, which is the recommended way.
Signed-off-by: Damien George <damien@micropython.org>
Improvements made:
- PSRAM support for S2
- partition definition for 16MiB flash
- correct ADC and DAC pins
- correct GPIO and IRQ pins
- S3 components in CMakeLists
Based on original commit made by Seon Rozenblum aka @UnexpectedMaker.
Signed-off-by: Damien George <damien@micropython.org>
The RP2040 has 2 cores and supports running at most 2 Python threads (the
main one plus another), and will raise OSError if a thread cannot be
created because core1 is already in use. This commit adjusts some thread
tests to be robust against such OSError's. These tests now pass on rp2
boards.
Signed-off-by: Damien George <damien@micropython.org>
