stm32/boards: Add support for NUCLEO-F746ZG evaluation board.
This is a low-cost evaluation kit board from ST based on the STM32 Nucleo-144 form factor. It uses the STM32F746ZG MCU in the LQFP144 package. The MCU has 1MB of flash and 320kB of System RAM. Cortex-M7 runs at up to 216MHz.
This commit is contained in:
Jaroslav Sykora
Damien George
parent
bbac2df0cf
commit
3e9e9b07ba
76
ports/stm32/boards/NUCLEO_F746ZG/mpconfigboard.h
Normal file
76
ports/stm32/boards/NUCLEO_F746ZG/mpconfigboard.h
Normal file
@ -0,0 +1,76 @@
|
||||
// This board is only confirmed to operate using DFU mode and openocd.
|
||||
// DFU mode can be accessed by setting BOOT0 (see schematics)
|
||||
// To use openocd run "OPENOCD_CONFIG=boards/openocd_stm32f7.cfg" in
|
||||
// the make command.
|
||||
|
||||
#define MICROPY_HW_BOARD_NAME "NUCLEO-F746ZG"
|
||||
#define MICROPY_HW_MCU_NAME "STM32F746"
|
||||
|
||||
#define MICROPY_HW_HAS_SWITCH (1)
|
||||
#define MICROPY_HW_HAS_FLASH (1)
|
||||
#define MICROPY_HW_HAS_SDCARD (0)
|
||||
#define MICROPY_HW_HAS_MMA7660 (0)
|
||||
#define MICROPY_HW_HAS_LIS3DSH (0)
|
||||
#define MICROPY_HW_HAS_LCD (0)
|
||||
#define MICROPY_HW_ENABLE_RNG (1)
|
||||
#define MICROPY_HW_ENABLE_RTC (1)
|
||||
#define MICROPY_HW_ENABLE_TIMER (1)
|
||||
#define MICROPY_HW_ENABLE_SERVO (0)
|
||||
#define MICROPY_HW_ENABLE_DAC (1)
|
||||
#define MICROPY_HW_ENABLE_CAN (1)
|
||||
|
||||
// HSE is 8MHz
|
||||
// VCOClock = HSE * PLLN / PLLM = 8 MHz * 216 / 4 = 432 MHz
|
||||
// SYSCLK = VCOClock / PLLP = 432 MHz / 2 = 216 MHz
|
||||
// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 432 MHz / 9 = 48 MHz
|
||||
#define MICROPY_HW_CLK_PLLM (4)
|
||||
#define MICROPY_HW_CLK_PLLN (216)
|
||||
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
||||
#define MICROPY_HW_CLK_PLLQ (9)
|
||||
|
||||
// From the reference manual, for 2.7V to 3.6V
|
||||
// 151-180 MHz => 5 wait states
|
||||
// 181-210 MHz => 6 wait states
|
||||
// 211-216 MHz => 7 wait states
|
||||
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_7 // 210-216 MHz needs 7 wait states
|
||||
|
||||
// UART config
|
||||
#define MICROPY_HW_UART2_TX (pin_D5)
|
||||
#define MICROPY_HW_UART2_RX (pin_D6)
|
||||
#define MICROPY_HW_UART2_RTS (pin_D4)
|
||||
#define MICROPY_HW_UART2_CTS (pin_D3)
|
||||
#define MICROPY_HW_UART3_TX (pin_D8)
|
||||
#define MICROPY_HW_UART3_RX (pin_D9)
|
||||
#define MICROPY_HW_UART6_TX (pin_G14)
|
||||
#define MICROPY_HW_UART6_RX (pin_G9)
|
||||
#define MICROPY_HW_UART_REPL PYB_UART_3
|
||||
#define MICROPY_HW_UART_REPL_BAUD 115200
|
||||
|
||||
// I2C busses
|
||||
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
||||
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
||||
#define MICROPY_HW_I2C3_SCL (pin_H7)
|
||||
#define MICROPY_HW_I2C3_SDA (pin_H8)
|
||||
|
||||
// SPI
|
||||
#define MICROPY_HW_SPI3_NSS (pin_A4)
|
||||
#define MICROPY_HW_SPI3_SCK (pin_B3)
|
||||
#define MICROPY_HW_SPI3_MISO (pin_B4)
|
||||
#define MICROPY_HW_SPI3_MOSI (pin_B5)
|
||||
|
||||
// USRSW is pulled low. Pressing the button makes the input go high.
|
||||
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
||||
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
||||
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
||||
#define MICROPY_HW_USRSW_PRESSED (1)
|
||||
|
||||
// LEDs
|
||||
#define MICROPY_HW_LED1 (pin_B0) // green
|
||||
#define MICROPY_HW_LED2 (pin_B7) // blue
|
||||
#define MICROPY_HW_LED3 (pin_B14) // red
|
||||
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
||||
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
||||
|
||||
// USB config (CN13 - USB OTG FS)
|
||||
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
||||
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|
||||
4
ports/stm32/boards/NUCLEO_F746ZG/mpconfigboard.mk
Normal file
4
ports/stm32/boards/NUCLEO_F746ZG/mpconfigboard.mk
Normal file
@ -0,0 +1,4 @@
|
||||
MCU_SERIES = f7
|
||||
CMSIS_MCU = STM32F746xx
|
||||
AF_FILE = boards/stm32f746_af.csv
|
||||
LD_FILE = boards/stm32f746.ld
|
||||
68
ports/stm32/boards/NUCLEO_F746ZG/pins.csv
Normal file
68
ports/stm32/boards/NUCLEO_F746ZG/pins.csv
Normal file
@ -0,0 +1,68 @@
|
||||
A0,PA3
|
||||
A1,PC0
|
||||
A2,PC3
|
||||
A3,PF3
|
||||
A4,PF5
|
||||
A5,PF10
|
||||
D0,PG9
|
||||
D1,PG14
|
||||
D2,PF15
|
||||
D3,PE13
|
||||
D4,PF14
|
||||
D5,PE11
|
||||
D6,PE9
|
||||
D7,PF13
|
||||
D8,PF12
|
||||
D9,PD15
|
||||
D10,PD14
|
||||
D11,PA7
|
||||
D12,PA6
|
||||
D13,PA5
|
||||
D14,PB9
|
||||
D15,PB8
|
||||
D16,PC6
|
||||
D17,PB15
|
||||
D18,PB13
|
||||
D19,PB12
|
||||
D20,PA15
|
||||
D21,PC7
|
||||
D22,PB5
|
||||
D23,PB3
|
||||
D24,PA4
|
||||
D25,PB4
|
||||
LED1,PB0
|
||||
LED2,PB7
|
||||
LED3,PB14
|
||||
SW,PC13
|
||||
TP1,PH2
|
||||
TP2,PI8
|
||||
TP3,PH15
|
||||
AUDIO_INT,PD6
|
||||
AUDIO_SDA,PH8
|
||||
AUDIO_SCL,PH7
|
||||
EXT_SDA,PB9
|
||||
EXT_SCL,PB8
|
||||
EXT_RST,PG3
|
||||
SD_SW,PC13
|
||||
LCD_BL_CTRL,PK3
|
||||
LCD_INT,PI13
|
||||
LCD_SDA,PH8
|
||||
LCD_SCL,PH7
|
||||
OTG_FS_POWER,PD5
|
||||
OTG_FS_OVER_CURRENT,PD4
|
||||
OTG_HS_OVER_CURRENT,PE3
|
||||
USB_VBUS,PJ12
|
||||
USB_ID,PA10
|
||||
USB_DM,PA11
|
||||
USB_DP,PA12
|
||||
VCP_TX,PD8
|
||||
VCP_RX,PD9
|
||||
UART2_TX,PD5
|
||||
UART2_RX,PD6
|
||||
UART2_RTS,PD4
|
||||
UART2_CTS,PD3
|
||||
UART6_TX,PG14
|
||||
UART6_RX,PG9
|
||||
SPI_B_NSS,PA4
|
||||
SPI_B_SCK,PB3
|
||||
SPI_B_MOSI,PB5
|
||||
|
429
ports/stm32/boards/NUCLEO_F746ZG/stm32f7xx_hal_conf.h
Normal file
429
ports/stm32/boards/NUCLEO_F746ZG/stm32f7xx_hal_conf.h
Normal file
@ -0,0 +1,429 @@
|
||||
/**
|
||||
******************************************************************************
|
||||
* @file stm32f7xx_hal_conf.h
|
||||
* @author MCD Application Team
|
||||
* @version V1.0.1
|
||||
* @date 25-June-2015
|
||||
* @brief HAL configuration file.
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without modification,
|
||||
* are permitted provided that the following conditions are met:
|
||||
* 1. Redistributions of source code must retain the above copyright notice,
|
||||
* this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
* this list of conditions and the following disclaimer in the documentation
|
||||
* and/or other materials provided with the distribution.
|
||||
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
||||
* may be used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
|
||||
/* Define to prevent recursive inclusion -------------------------------------*/
|
||||
#ifndef __STM32F7xx_HAL_CONF_H
|
||||
#define __STM32F7xx_HAL_CONF_H
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
/* Exported types ------------------------------------------------------------*/
|
||||
/* Exported constants --------------------------------------------------------*/
|
||||
|
||||
#define USE_USB_FS
|
||||
|
||||
/* ########################## Module Selection ############################## */
|
||||
/**
|
||||
* @brief This is the list of modules to be used in the HAL driver
|
||||
*/
|
||||
#define HAL_MODULE_ENABLED
|
||||
#define HAL_ADC_MODULE_ENABLED
|
||||
#define HAL_CAN_MODULE_ENABLED
|
||||
/* #define HAL_CEC_MODULE_ENABLED */
|
||||
/* #define HAL_CRC_MODULE_ENABLED */
|
||||
/* #define HAL_CRYP_MODULE_ENABLED */
|
||||
#define HAL_DAC_MODULE_ENABLED
|
||||
/* #define HAL_DCMI_MODULE_ENABLED */
|
||||
#define HAL_DMA_MODULE_ENABLED
|
||||
/* #define HAL_DMA2D_MODULE_ENABLED */
|
||||
/* #define HAL_ETH_MODULE_ENABLED */
|
||||
#define HAL_FLASH_MODULE_ENABLED
|
||||
/* #define HAL_NAND_MODULE_ENABLED */
|
||||
/* #define HAL_NOR_MODULE_ENABLED */
|
||||
/* #define HAL_SRAM_MODULE_ENABLED */
|
||||
/* #define HAL_SDRAM_MODULE_ENABLED */
|
||||
/* #define HAL_HASH_MODULE_ENABLED */
|
||||
#define HAL_GPIO_MODULE_ENABLED
|
||||
#define HAL_I2C_MODULE_ENABLED
|
||||
#define HAL_I2S_MODULE_ENABLED
|
||||
/* #define HAL_IWDG_MODULE_ENABLED */
|
||||
/* #define HAL_LPTIM_MODULE_ENABLED */
|
||||
/* #define HAL_LTDC_MODULE_ENABLED */
|
||||
#define HAL_PWR_MODULE_ENABLED
|
||||
/* #define HAL_QSPI_MODULE_ENABLED */
|
||||
#define HAL_RCC_MODULE_ENABLED
|
||||
#define HAL_RNG_MODULE_ENABLED
|
||||
#define HAL_RTC_MODULE_ENABLED
|
||||
/* #define HAL_SAI_MODULE_ENABLED */
|
||||
#define HAL_SD_MODULE_ENABLED
|
||||
/* #define HAL_SPDIFRX_MODULE_ENABLED */
|
||||
#define HAL_SPI_MODULE_ENABLED
|
||||
#define HAL_TIM_MODULE_ENABLED
|
||||
#define HAL_UART_MODULE_ENABLED
|
||||
/* #define HAL_USART_MODULE_ENABLED */
|
||||
/* #define HAL_IRDA_MODULE_ENABLED */
|
||||
/* #define HAL_SMARTCARD_MODULE_ENABLED */
|
||||
/* #define HAL_WWDG_MODULE_ENABLED */
|
||||
#define HAL_CORTEX_MODULE_ENABLED
|
||||
#define HAL_PCD_MODULE_ENABLED
|
||||
/* #define HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
|
||||
/* ########################## Timeout Configuration ######################### */
|
||||
/**
|
||||
* @brief This is the HAL configuration section
|
||||
*/
|
||||
#define HAL_ACCURATE_TIMEOUT_ENABLED 0
|
||||
#define HAL_TIMEOUT_VALUE 0x1FFFFFF
|
||||
|
||||
/* ########################## HSE/HSI Values adaptation ##################### */
|
||||
/**
|
||||
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSE is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSE_VALUE)
|
||||
#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
|
||||
#endif /* HSE_VALUE */
|
||||
|
||||
#if !defined (HSE_STARTUP_TIMEOUT)
|
||||
#define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */
|
||||
#endif /* HSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief Internal High Speed oscillator (HSI) value.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSI is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSI_VALUE)
|
||||
#define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* HSI_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal Low Speed oscillator (LSI) value.
|
||||
*/
|
||||
#if !defined (LSI_VALUE)
|
||||
#define LSI_VALUE ((uint32_t)32000)
|
||||
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
|
||||
The real value may vary depending on the variations
|
||||
in voltage and temperature. */
|
||||
/**
|
||||
* @brief External Low Speed oscillator (LSE) value.
|
||||
*/
|
||||
#if !defined (LSE_VALUE)
|
||||
#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
|
||||
#endif /* LSE_VALUE */
|
||||
|
||||
#if !defined (LSE_STARTUP_TIMEOUT)
|
||||
#define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
|
||||
#endif /* LSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief External clock source for I2S peripheral
|
||||
* This value is used by the I2S HAL module to compute the I2S clock source
|
||||
* frequency, this source is inserted directly through I2S_CKIN pad.
|
||||
*/
|
||||
#if !defined (EXTERNAL_CLOCK_VALUE)
|
||||
#define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* EXTERNAL_CLOCK_VALUE */
|
||||
|
||||
/* Tip: To avoid modifying this file each time you need to use different HSE,
|
||||
=== you can define the HSE value in your toolchain compiler preprocessor. */
|
||||
|
||||
/* ########################### System Configuration ######################### */
|
||||
/**
|
||||
* @brief This is the HAL system configuration section
|
||||
*/
|
||||
#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
|
||||
#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
|
||||
#define USE_RTOS 0
|
||||
#define ART_ACCLERATOR_ENABLE 1 /* To enable instruction cache and prefetch */
|
||||
|
||||
/* ########################## Assert Selection ############################## */
|
||||
/**
|
||||
* @brief Uncomment the line below to expanse the "assert_param" macro in the
|
||||
* HAL drivers code
|
||||
*/
|
||||
/* #define USE_FULL_ASSERT 1 */
|
||||
|
||||
/* ################## Ethernet peripheral configuration ##################### */
|
||||
|
||||
/* Section 1 : Ethernet peripheral configuration */
|
||||
|
||||
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
|
||||
#define MAC_ADDR0 2
|
||||
#define MAC_ADDR1 1
|
||||
#define MAC_ADDR2 0
|
||||
#define MAC_ADDR3 0
|
||||
#define MAC_ADDR4 0
|
||||
#define MAC_ADDR5 0
|
||||
|
||||
/* Definition of the Ethernet driver buffers size and count */
|
||||
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
|
||||
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
|
||||
#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
|
||||
#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
|
||||
|
||||
/* Section 2: PHY configuration section */
|
||||
/* LAN8742A PHY Address*/
|
||||
#define LAN8742A_PHY_ADDRESS 0x00
|
||||
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
|
||||
#define PHY_RESET_DELAY ((uint32_t)0x00000FFF)
|
||||
/* PHY Configuration delay */
|
||||
#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFF)
|
||||
|
||||
#define PHY_READ_TO ((uint32_t)0x0000FFFF)
|
||||
#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
|
||||
|
||||
/* Section 3: Common PHY Registers */
|
||||
|
||||
#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
|
||||
#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
|
||||
|
||||
#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
|
||||
#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
|
||||
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
|
||||
#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
|
||||
#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
|
||||
#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
|
||||
#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
|
||||
#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
|
||||
#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
|
||||
#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
|
||||
|
||||
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
|
||||
#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
|
||||
#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
|
||||
|
||||
/* Section 4: Extended PHY Registers */
|
||||
|
||||
#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
|
||||
#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
|
||||
#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
|
||||
|
||||
#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
|
||||
#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
|
||||
#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
|
||||
|
||||
#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
|
||||
#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
|
||||
|
||||
#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
|
||||
#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
|
||||
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
/**
|
||||
* @brief Include module's header file
|
||||
*/
|
||||
|
||||
#ifdef HAL_RCC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_rcc.h"
|
||||
#endif /* HAL_RCC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_GPIO_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_gpio.h"
|
||||
#endif /* HAL_GPIO_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_dma.h"
|
||||
#endif /* HAL_DMA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CORTEX_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_cortex.h"
|
||||
#endif /* HAL_CORTEX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_adc.h"
|
||||
#endif /* HAL_ADC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_can.h"
|
||||
#endif /* HAL_CAN_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CEC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_cec.h"
|
||||
#endif /* HAL_CEC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_crc.h"
|
||||
#endif /* HAL_CRC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRYP_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_cryp.h"
|
||||
#endif /* HAL_CRYP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA2D_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_dma2d.h"
|
||||
#endif /* HAL_DMA2D_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DAC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_dac.h"
|
||||
#endif /* HAL_DAC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DCMI_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_dcmi.h"
|
||||
#endif /* HAL_DCMI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ETH_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_eth.h"
|
||||
#endif /* HAL_ETH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FLASH_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_flash.h"
|
||||
#endif /* HAL_FLASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SRAM_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_sram.h"
|
||||
#endif /* HAL_SRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NOR_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_nor.h"
|
||||
#endif /* HAL_NOR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NAND_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_nand.h"
|
||||
#endif /* HAL_NAND_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SDRAM_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_sdram.h"
|
||||
#endif /* HAL_SDRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HASH_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_hash.h"
|
||||
#endif /* HAL_HASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_i2c.h"
|
||||
#endif /* HAL_I2C_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2S_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_i2s.h"
|
||||
#endif /* HAL_I2S_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IWDG_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_iwdg.h"
|
||||
#endif /* HAL_IWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LPTIM_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_lptim.h"
|
||||
#endif /* HAL_LPTIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LTDC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_ltdc.h"
|
||||
#endif /* HAL_LTDC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PWR_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_pwr.h"
|
||||
#endif /* HAL_PWR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_qspi.h"
|
||||
#endif /* HAL_QSPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RNG_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_rng.h"
|
||||
#endif /* HAL_RNG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RTC_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_rtc.h"
|
||||
#endif /* HAL_RTC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SAI_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_sai.h"
|
||||
#endif /* HAL_SAI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_sd.h"
|
||||
#endif /* HAL_SD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPDIFRX_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_spdifrx.h"
|
||||
#endif /* HAL_SPDIFRX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_spi.h"
|
||||
#endif /* HAL_SPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_tim.h"
|
||||
#endif /* HAL_TIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_uart.h"
|
||||
#endif /* HAL_UART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_USART_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_usart.h"
|
||||
#endif /* HAL_USART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IRDA_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_irda.h"
|
||||
#endif /* HAL_IRDA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMARTCARD_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_smartcard.h"
|
||||
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_WWDG_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_wwdg.h"
|
||||
#endif /* HAL_WWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_pcd.h"
|
||||
#endif /* HAL_PCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HCD_MODULE_ENABLED
|
||||
#include "stm32f7xx_hal_hcd.h"
|
||||
#endif /* HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
/* Exported macro ------------------------------------------------------------*/
|
||||
#ifdef USE_FULL_ASSERT
|
||||
/**
|
||||
* @brief The assert_param macro is used for function's parameters check.
|
||||
* @param expr: If expr is false, it calls assert_failed function
|
||||
* which reports the name of the source file and the source
|
||||
* line number of the call that failed.
|
||||
* If expr is true, it returns no value.
|
||||
* @retval None
|
||||
*/
|
||||
#define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
|
||||
/* Exported functions ------------------------------------------------------- */
|
||||
void assert_failed(uint8_t* file, uint32_t line);
|
||||
#else
|
||||
#define assert_param(expr) ((void)0)
|
||||
#endif /* USE_FULL_ASSERT */
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __STM32F7xx_HAL_CONF_H */
|
||||
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||||
Loading…
Reference in New Issue
Block a user