circuitpython/stm/stmperiph/stm32f4xx_dac.c

/**
  ******************************************************************************
  * @file    stm32f4xx_dac.c
  * @author  MCD Application Team
  * @version V1.3.0
  * @date    08-November-2013
   * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the Digital-to-Analog Converter (DAC) peripheral: 
  *           + DAC channels configuration: trigger, output buffer, data format
  *           + DMA management      
  *           + Interrupts and flags management
  *
 @verbatim      
 ===============================================================================
                      ##### DAC Peripheral features #####
 ===============================================================================
    [..]        
      *** DAC Channels ***
      ====================  
    [..]  
    The device integrates two 12-bit Digital Analog Converters that can 
    be used independently or simultaneously (dual mode):
      (#) DAC channel1 with DAC_OUT1 (PA4) as output
      (#) DAC channel2 with DAC_OUT2 (PA5) as output
  
      *** DAC Triggers ***
      ====================
    [..]
    Digital to Analog conversion can be non-triggered using DAC_Trigger_None
    and DAC_OUT1/DAC_OUT2 is available once writing to DHRx register 
    using DAC_SetChannel1Data() / DAC_SetChannel2Data() functions.
    [..] 
    Digital to Analog conversion can be triggered by:
      (#) External event: EXTI Line 9 (any GPIOx_Pin9) using DAC_Trigger_Ext_IT9.
          The used pin (GPIOx_Pin9) must be configured in input mode.
  
      (#) Timers TRGO: TIM2, TIM4, TIM5, TIM6, TIM7 and TIM8 
          (DAC_Trigger_T2_TRGO, DAC_Trigger_T4_TRGO...)
          The timer TRGO event should be selected using TIM_SelectOutputTrigger()
  
      (#) Software using DAC_Trigger_Software
  
      *** DAC Buffer mode feature ***
      =============================== 
      [..] 
      Each DAC channel integrates an output buffer that can be used to 
      reduce the output impedance, and to drive external loads directly
      without having to add an external operational amplifier.
      To enable, the output buffer use  
      DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Enable;
      [..]           
      (@) Refer to the device datasheet for more details about output 
          impedance value with and without output buffer.
            
       *** DAC wave generation feature ***
       =================================== 
       [..]     
       Both DAC channels can be used to generate
         (#) Noise wave using DAC_WaveGeneration_Noise
         (#) Triangle wave using DAC_WaveGeneration_Triangle
          
          -@-  Wave generation can be disabled using DAC_WaveGeneration_None
  
       *** DAC data format ***
       =======================
       [..]   
       The DAC data format can be:
         (#) 8-bit right alignment using DAC_Align_8b_R
         (#) 12-bit left alignment using DAC_Align_12b_L
         (#) 12-bit right alignment using DAC_Align_12b_R
  
       *** DAC data value to voltage correspondence ***  
       ================================================ 
       [..] 
       The analog output voltage on each DAC channel pin is determined
       by the following equation: 
       DAC_OUTx = VREF+ * DOR / 4095
       with  DOR is the Data Output Register
          VEF+ is the input voltage reference (refer to the device datasheet)
        e.g. To set DAC_OUT1 to 0.7V, use
          DAC_SetChannel1Data(DAC_Align_12b_R, 868);
          Assuming that VREF+ = 3.3V, DAC_OUT1 = (3.3 * 868) / 4095 = 0.7V
  
       *** DMA requests  ***
       =====================
       [..]    
       A DMA1 request can be generated when an external trigger (but not
       a software trigger) occurs if DMA1 requests are enabled using
       DAC_DMACmd()
       [..]
       DMA1 requests are mapped as following:
         (#) DAC channel1 : mapped on DMA1 Stream5 channel7 which must be 
             already configured
         (#) DAC channel2 : mapped on DMA1 Stream6 channel7 which must be 
             already configured
  
      
                      ##### How to use this driver #####
 ===============================================================================
    [..]          
      (+) DAC APB clock must be enabled to get write access to DAC
          registers using
          RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE)
      (+) Configure DAC_OUTx (DAC_OUT1: PA4, DAC_OUT2: PA5) in analog mode.
      (+) Configure the DAC channel using DAC_Init() function
      (+) Enable the DAC channel using DAC_Cmd() function
   
 @endverbatim    
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************  
  */ 


/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_dac.h"
#include "stm32f4xx_rcc.h"

/** @addtogroup STM32F4xx_StdPeriph_Driver
  * @{
  */

/** @defgroup DAC 
  * @brief DAC driver modules
  * @{
  */ 

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/

/* CR register Mask */
#define CR_CLEAR_MASK              ((uint32_t)0x00000FFE)

/* DAC Dual Channels SWTRIG masks */
#define DUAL_SWTRIG_SET            ((uint32_t)0x00000003)
#define DUAL_SWTRIG_RESET          ((uint32_t)0xFFFFFFFC)

/* DHR registers offsets */
#define DHR12R1_OFFSET             ((uint32_t)0x00000008)
#define DHR12R2_OFFSET             ((uint32_t)0x00000014)
#define DHR12RD_OFFSET             ((uint32_t)0x00000020)

/* DOR register offset */
#define DOR_OFFSET                 ((uint32_t)0x0000002C)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup DAC_Private_Functions
  * @{
  */

/** @defgroup DAC_Group1 DAC channels configuration
 *  @brief   DAC channels configuration: trigger, output buffer, data format 
 *
@verbatim   
 ===============================================================================
   ##### DAC channels configuration: trigger, output buffer, data format #####
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Deinitializes the DAC peripheral registers to their default reset values.
  * @param  None
  * @retval None
  */
void DAC_DeInit(void)
{
  /* Enable DAC reset state */
  RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, ENABLE);
  /* Release DAC from reset state */
  RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, DISABLE);
}

/**
  * @brief  Initializes the DAC peripheral according to the specified parameters
  *         in the DAC_InitStruct.
  * @param  DAC_Channel: the selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_InitStruct: pointer to a DAC_InitTypeDef structure that contains
  *         the configuration information for the  specified DAC channel.
  * @retval None
  */
void DAC_Init(uint32_t DAC_Channel, DAC_InitTypeDef* DAC_InitStruct)
{
  uint32_t tmpreg1 = 0, tmpreg2 = 0;

  /* Check the DAC parameters */
  assert_param(IS_DAC_TRIGGER(DAC_InitStruct->DAC_Trigger));
  assert_param(IS_DAC_GENERATE_WAVE(DAC_InitStruct->DAC_WaveGeneration));
  assert_param(IS_DAC_LFSR_UNMASK_TRIANGLE_AMPLITUDE(DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude));
  assert_param(IS_DAC_OUTPUT_BUFFER_STATE(DAC_InitStruct->DAC_OutputBuffer));

/*---------------------------- DAC CR Configuration --------------------------*/
  /* Get the DAC CR value */
  tmpreg1 = DAC->CR;
  /* Clear BOFFx, TENx, TSELx, WAVEx and MAMPx bits */
  tmpreg1 &= ~(CR_CLEAR_MASK << DAC_Channel);
  /* Configure for the selected DAC channel: buffer output, trigger, 
     wave generation, mask/amplitude for wave generation */
  /* Set TSELx and TENx bits according to DAC_Trigger value */
  /* Set WAVEx bits according to DAC_WaveGeneration value */
  /* Set MAMPx bits according to DAC_LFSRUnmask_TriangleAmplitude value */ 
  /* Set BOFFx bit according to DAC_OutputBuffer value */   
  tmpreg2 = (DAC_InitStruct->DAC_Trigger | DAC_InitStruct->DAC_WaveGeneration |
             DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude | \
             DAC_InitStruct->DAC_OutputBuffer);
  /* Calculate CR register value depending on DAC_Channel */
  tmpreg1 |= tmpreg2 << DAC_Channel;
  /* Write to DAC CR */
  DAC->CR = tmpreg1;
}

/**
  * @brief  Fills each DAC_InitStruct member with its default value.
  * @param  DAC_InitStruct: pointer to a DAC_InitTypeDef structure which will 
  *         be initialized.
  * @retval None
  */
void DAC_StructInit(DAC_InitTypeDef* DAC_InitStruct)
{
/*--------------- Reset DAC init structure parameters values -----------------*/
  /* Initialize the DAC_Trigger member */
  DAC_InitStruct->DAC_Trigger = DAC_Trigger_None;
  /* Initialize the DAC_WaveGeneration member */
  DAC_InitStruct->DAC_WaveGeneration = DAC_WaveGeneration_None;
  /* Initialize the DAC_LFSRUnmask_TriangleAmplitude member */
  DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude = DAC_LFSRUnmask_Bit0;
  /* Initialize the DAC_OutputBuffer member */
  DAC_InitStruct->DAC_OutputBuffer = DAC_OutputBuffer_Enable;
}

/**
  * @brief  Enables or disables the specified DAC channel.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the DAC channel. 
  *          This parameter can be: ENABLE or DISABLE.
  * @note   When the DAC channel is enabled the trigger source can no more be modified.
  * @retval None
  */
void DAC_Cmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC channel */
    DAC->CR |= (DAC_CR_EN1 << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC channel */
    DAC->CR &= (~(DAC_CR_EN1 << DAC_Channel));
  }
}

/**
  * @brief  Enables or disables the selected DAC channel software trigger.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the selected DAC channel software trigger.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DAC_SoftwareTriggerCmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable software trigger for the selected DAC channel */
    DAC->SWTRIGR |= (uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4);
  }
  else
  {
    /* Disable software trigger for the selected DAC channel */
    DAC->SWTRIGR &= ~((uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4));
  }
}

/**
  * @brief  Enables or disables simultaneously the two DAC channels software triggers.
  * @param  NewState: new state of the DAC channels software triggers.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void DAC_DualSoftwareTriggerCmd(FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable software trigger for both DAC channels */
    DAC->SWTRIGR |= DUAL_SWTRIG_SET;
  }
  else
  {
    /* Disable software trigger for both DAC channels */
    DAC->SWTRIGR &= DUAL_SWTRIG_RESET;
  }
}

/**
  * @brief  Enables or disables the selected DAC channel wave generation.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_Wave: specifies the wave type to enable or disable.
  *          This parameter can be one of the following values:
  *            @arg DAC_Wave_Noise: noise wave generation
  *            @arg DAC_Wave_Triangle: triangle wave generation
  * @param  NewState: new state of the selected DAC channel wave generation.
  *          This parameter can be: ENABLE or DISABLE.  
  * @retval None
  */
void DAC_WaveGenerationCmd(uint32_t DAC_Channel, uint32_t DAC_Wave, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_WAVE(DAC_Wave)); 
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected wave generation for the selected DAC channel */
    DAC->CR |= DAC_Wave << DAC_Channel;
  }
  else
  {
    /* Disable the selected wave generation for the selected DAC channel */
    DAC->CR &= ~(DAC_Wave << DAC_Channel);
  }
}

/**
  * @brief  Set the specified data holding register value for DAC channel1.
  * @param  DAC_Align: Specifies the data alignment for DAC channel1.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data: Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel1Data(uint32_t DAC_Align, uint16_t Data)
{  
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE; 
  tmp += DHR12R1_OFFSET + DAC_Align;

  /* Set the DAC channel1 selected data holding register */
  *(__IO uint32_t *) tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for DAC channel2.
  * @param  DAC_Align: Specifies the data alignment for DAC channel2.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data: Data to be loaded in the selected data holding register.
  * @retval None
  */
void DAC_SetChannel2Data(uint32_t DAC_Align, uint16_t Data)
{
  __IO uint32_t tmp = 0;

  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data));
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12R2_OFFSET + DAC_Align;

  /* Set the DAC channel2 selected data holding register */
  *(__IO uint32_t *)tmp = Data;
}

/**
  * @brief  Set the specified data holding register value for dual channel DAC.
  * @param  DAC_Align: Specifies the data alignment for dual channel DAC.
  *          This parameter can be one of the following values:
  *            @arg DAC_Align_8b_R: 8bit right data alignment selected
  *            @arg DAC_Align_12b_L: 12bit left data alignment selected
  *            @arg DAC_Align_12b_R: 12bit right data alignment selected
  * @param  Data2: Data for DAC Channel2 to be loaded in the selected data holding register.
  * @param  Data1: Data for DAC Channel1 to be loaded in the selected data  holding register.
  * @note   In dual mode, a unique register access is required to write in both
  *          DAC channels at the same time.
  * @retval None
  */
void DAC_SetDualChannelData(uint32_t DAC_Align, uint16_t Data2, uint16_t Data1)
{
  uint32_t data = 0, tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_ALIGN(DAC_Align));
  assert_param(IS_DAC_DATA(Data1));
  assert_param(IS_DAC_DATA(Data2));
  
  /* Calculate and set dual DAC data holding register value */
  if (DAC_Align == DAC_Align_8b_R)
  {
    data = ((uint32_t)Data2 << 8) | Data1; 
  }
  else
  {
    data = ((uint32_t)Data2 << 16) | Data1;
  }
  
  tmp = (uint32_t)DAC_BASE;
  tmp += DHR12RD_OFFSET + DAC_Align;

  /* Set the dual DAC selected data holding register */
  *(__IO uint32_t *)tmp = data;
}

/**
  * @brief  Returns the last data output value of the selected DAC channel.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @retval The selected DAC channel data output value.
  */
uint16_t DAC_GetDataOutputValue(uint32_t DAC_Channel)
{
  __IO uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  
  tmp = (uint32_t) DAC_BASE ;
  tmp += DOR_OFFSET + ((uint32_t)DAC_Channel >> 2);
  
  /* Returns the DAC channel data output register value */
  return (uint16_t) (*(__IO uint32_t*) tmp);
}
/**
  * @}
  */

/** @defgroup DAC_Group2 DMA management functions
 *  @brief   DMA management functions
 *
@verbatim   
 ===============================================================================
                       ##### DMA management functions #####
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Enables or disables the specified DAC channel DMA request.
  * @note   When enabled DMA1 is generated when an external trigger (EXTI Line9,
  *         TIM2, TIM4, TIM5, TIM6, TIM7 or TIM8  but not a software trigger) occurs.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  NewState: new state of the selected DAC channel DMA request.
  *          This parameter can be: ENABLE or DISABLE.
  * @note   The DAC channel1 is mapped on DMA1 Stream 5 channel7 which must be
  *          already configured.
  * @note   The DAC channel2 is mapped on DMA1 Stream 6 channel7 which must be
  *          already configured.    
  * @retval None
  */
void DAC_DMACmd(uint32_t DAC_Channel, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC channel DMA request */
    DAC->CR |= (DAC_CR_DMAEN1 << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC channel DMA request */
    DAC->CR &= (~(DAC_CR_DMAEN1 << DAC_Channel));
  }
}
/**
  * @}
  */

/** @defgroup DAC_Group3 Interrupts and flags management functions
 *  @brief   Interrupts and flags management functions
 *
@verbatim   
 ===============================================================================
             ##### Interrupts and flags management functions #####
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Enables or disables the specified DAC interrupts.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt sources to be enabled or disabled. 
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @param  NewState: new state of the specified DAC interrupts.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */ 
void DAC_ITConfig(uint32_t DAC_Channel, uint32_t DAC_IT, FunctionalState NewState)  
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  assert_param(IS_DAC_IT(DAC_IT)); 

  if (NewState != DISABLE)
  {
    /* Enable the selected DAC interrupts */
    DAC->CR |=  (DAC_IT << DAC_Channel);
  }
  else
  {
    /* Disable the selected DAC interrupts */
    DAC->CR &= (~(uint32_t)(DAC_IT << DAC_Channel));
  }
}

/**
  * @brief  Checks whether the specified DAC flag is set or not.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to check. 
  *          This parameter can be only of the following value:
  *            @arg DAC_FLAG_DMAUDR: DMA underrun flag
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @retval The new state of DAC_FLAG (SET or RESET).
  */
FlagStatus DAC_GetFlagStatus(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Check the status of the specified DAC flag */
  if ((DAC->SR & (DAC_FLAG << DAC_Channel)) != (uint8_t)RESET)
  {
    /* DAC_FLAG is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_FLAG is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channel's pending flags.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_FLAG: specifies the flag to clear. 
  *          This parameter can be of the following value:
  *            @arg DAC_FLAG_DMAUDR: DMA underrun flag 
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).                           
  * @retval None
  */
void DAC_ClearFlag(uint32_t DAC_Channel, uint32_t DAC_FLAG)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_FLAG(DAC_FLAG));

  /* Clear the selected DAC flags */
  DAC->SR = (DAC_FLAG << DAC_Channel);
}

/**
  * @brief  Checks whether the specified DAC interrupt has occurred or not.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt source to check. 
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).
  * @retval The new state of DAC_IT (SET or RESET).
  */
ITStatus DAC_GetITStatus(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  ITStatus bitstatus = RESET;
  uint32_t enablestatus = 0;
  
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT));

  /* Get the DAC_IT enable bit status */
  enablestatus = (DAC->CR & (DAC_IT << DAC_Channel)) ;
  
  /* Check the status of the specified DAC interrupt */
  if (((DAC->SR & (DAC_IT << DAC_Channel)) != (uint32_t)RESET) && enablestatus)
  {
    /* DAC_IT is set */
    bitstatus = SET;
  }
  else
  {
    /* DAC_IT is reset */
    bitstatus = RESET;
  }
  /* Return the DAC_IT status */
  return  bitstatus;
}

/**
  * @brief  Clears the DAC channel's interrupt pending bits.
  * @param  DAC_Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_Channel_1: DAC Channel1 selected
  *            @arg DAC_Channel_2: DAC Channel2 selected
  * @param  DAC_IT: specifies the DAC interrupt pending bit to clear.
  *          This parameter can be the following values:
  *            @arg DAC_IT_DMAUDR: DMA underrun interrupt mask                         
  * @note   The DMA underrun occurs when a second external trigger arrives before the 
  *         acknowledgement for the first external trigger is received (first request).                           
  * @retval None
  */
void DAC_ClearITPendingBit(uint32_t DAC_Channel, uint32_t DAC_IT)
{
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(DAC_Channel));
  assert_param(IS_DAC_IT(DAC_IT)); 

  /* Clear the selected DAC interrupt pending bits */
  DAC->SR = (DAC_IT << DAC_Channel);
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/