circuitpython/stm/lib/stm32f4xx_exti.c

313 lines
9.7 KiB
C
Raw Normal View History

2013-10-12 19:42:20 -04:00
/**
******************************************************************************
* @file stm32f4xx_exti.c
* @author MCD Application Team
* @version V1.3.0
* @date 08-November-2013
2013-10-12 19:42:20 -04:00
* @brief This file provides firmware functions to manage the following
* functionalities of the EXTI peripheral:
* + Initialization and Configuration
* + Interrupts and flags management
*
@verbatim
===================================================================
##### EXTI features #####
===================================================================
[..] External interrupt/event lines are mapped as following:
(#) All available GPIO pins are connected to the 16 external
interrupt/event lines from EXTI0 to EXTI15.
(#) EXTI line 16 is connected to the PVD Output
(#) EXTI line 17 is connected to the RTC Alarm event
(#) EXTI line 18 is connected to the USB OTG FS Wakeup from suspend event
(#) EXTI line 19 is connected to the Ethernet Wakeup event
(#) EXTI line 20 is connected to the USB OTG HS (configured in FS) Wakeup event
(#) EXTI line 21 is connected to the RTC Tamper and Time Stamp events
(#) EXTI line 22 is connected to the RTC Wakeup event
##### How to use this driver #####
===================================================================
[..] In order to use an I/O pin as an external interrupt source, follow steps
below:
(#) Configure the I/O in input mode using GPIO_Init()
(#) Select the input source pin for the EXTI line using SYSCFG_EXTILineConfig()
(#) Select the mode(interrupt, event) and configure the trigger
selection (Rising, falling or both) using EXTI_Init()
(#) Configure NVIC IRQ channel mapped to the EXTI line using NVIC_Init()
[..]
(@) SYSCFG APB clock must be enabled to get write access to SYSCFG_EXTICRx
registers using RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
@endverbatim
*
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_exti.h"
/** @addtogroup STM32F4xx_StdPeriph_Driver
* @{
*/
/** @defgroup EXTI
* @brief EXTI driver modules
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define EXTI_LINENONE ((uint32_t)0x00000) /* No interrupt selected */
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup EXTI_Private_Functions
* @{
*/
/** @defgroup EXTI_Group1 Initialization and Configuration functions
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization and Configuration functions #####
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Deinitializes the EXTI peripheral registers to their default reset values.
* @param None
* @retval None
*/
void EXTI_DeInit(void)
{
EXTI->IMR = 0x00000000;
EXTI->EMR = 0x00000000;
EXTI->RTSR = 0x00000000;
EXTI->FTSR = 0x00000000;
EXTI->PR = 0x007FFFFF;
}
/**
* @brief Initializes the EXTI peripheral according to the specified
* parameters in the EXTI_InitStruct.
* @param EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure
* that contains the configuration information for the EXTI peripheral.
* @retval None
*/
void EXTI_Init(EXTI_InitTypeDef* EXTI_InitStruct)
{
uint32_t tmp = 0;
/* Check the parameters */
assert_param(IS_EXTI_MODE(EXTI_InitStruct->EXTI_Mode));
assert_param(IS_EXTI_TRIGGER(EXTI_InitStruct->EXTI_Trigger));
assert_param(IS_EXTI_LINE(EXTI_InitStruct->EXTI_Line));
assert_param(IS_FUNCTIONAL_STATE(EXTI_InitStruct->EXTI_LineCmd));
tmp = (uint32_t)EXTI_BASE;
if (EXTI_InitStruct->EXTI_LineCmd != DISABLE)
{
/* Clear EXTI line configuration */
EXTI->IMR &= ~EXTI_InitStruct->EXTI_Line;
EXTI->EMR &= ~EXTI_InitStruct->EXTI_Line;
tmp += EXTI_InitStruct->EXTI_Mode;
*(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
/* Clear Rising Falling edge configuration */
EXTI->RTSR &= ~EXTI_InitStruct->EXTI_Line;
EXTI->FTSR &= ~EXTI_InitStruct->EXTI_Line;
/* Select the trigger for the selected external interrupts */
if (EXTI_InitStruct->EXTI_Trigger == EXTI_Trigger_Rising_Falling)
{
/* Rising Falling edge */
EXTI->RTSR |= EXTI_InitStruct->EXTI_Line;
EXTI->FTSR |= EXTI_InitStruct->EXTI_Line;
}
else
{
tmp = (uint32_t)EXTI_BASE;
tmp += EXTI_InitStruct->EXTI_Trigger;
*(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
}
}
else
{
tmp += EXTI_InitStruct->EXTI_Mode;
/* Disable the selected external lines */
*(__IO uint32_t *) tmp &= ~EXTI_InitStruct->EXTI_Line;
}
}
/**
* @brief Fills each EXTI_InitStruct member with its reset value.
* @param EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure which will
* be initialized.
* @retval None
*/
void EXTI_StructInit(EXTI_InitTypeDef* EXTI_InitStruct)
{
EXTI_InitStruct->EXTI_Line = EXTI_LINENONE;
EXTI_InitStruct->EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStruct->EXTI_Trigger = EXTI_Trigger_Falling;
EXTI_InitStruct->EXTI_LineCmd = DISABLE;
}
/**
* @brief Generates a Software interrupt on selected EXTI line.
* @param EXTI_Line: specifies the EXTI line on which the software interrupt
* will be generated.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_GenerateSWInterrupt(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->SWIER |= EXTI_Line;
}
/**
* @}
*/
/** @defgroup EXTI_Group2 Interrupts and flags management functions
* @brief Interrupts and flags management functions
*
@verbatim
===============================================================================
##### Interrupts and flags management functions #####
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Checks whether the specified EXTI line flag is set or not.
* @param EXTI_Line: specifies the EXTI line flag to check.
* This parameter can be EXTI_Linex where x can be(0..22)
* @retval The new state of EXTI_Line (SET or RESET).
*/
FlagStatus EXTI_GetFlagStatus(uint32_t EXTI_Line)
{
FlagStatus bitstatus = RESET;
/* Check the parameters */
assert_param(IS_GET_EXTI_LINE(EXTI_Line));
if ((EXTI->PR & EXTI_Line) != (uint32_t)RESET)
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
return bitstatus;
}
/**
* @brief Clears the EXTI's line pending flags.
* @param EXTI_Line: specifies the EXTI lines flags to clear.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_ClearFlag(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->PR = EXTI_Line;
}
/**
* @brief Checks whether the specified EXTI line is asserted or not.
* @param EXTI_Line: specifies the EXTI line to check.
* This parameter can be EXTI_Linex where x can be(0..22)
* @retval The new state of EXTI_Line (SET or RESET).
*/
ITStatus EXTI_GetITStatus(uint32_t EXTI_Line)
{
FlagStatus bitstatus = RESET;
2013-10-12 19:42:20 -04:00
/* Check the parameters */
assert_param(IS_GET_EXTI_LINE(EXTI_Line));
if ((EXTI->PR & EXTI_Line) != (uint32_t)RESET)
2013-10-12 19:42:20 -04:00
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
return bitstatus;
2013-10-12 19:42:20 -04:00
}
/**
* @brief Clears the EXTI's line pending bits.
* @param EXTI_Line: specifies the EXTI lines to clear.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_ClearITPendingBit(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->PR = EXTI_Line;
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/