circuitpython/ports/stm32/boards/PYBV3/mpconfigboard.h

93 lines
3.3 KiB
C
Raw Normal View History

#define MICROPY_HW_BOARD_NAME "PYBv3"
2014-06-26 18:35:53 -04:00
#define MICROPY_HW_MCU_NAME "STM32F405RG"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_HAS_MMA7660 (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
// The pyboard has a 32kHz crystal for the RTC
#define MICROPY_HW_RTC_USE_LSE (1)
// UART config
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART3_TX (pin_B10)
#define MICROPY_HW_UART3_RX (pin_B11)
#define MICROPY_HW_UART3_RTS (pin_B14)
#define MICROPY_HW_UART3_CTS (pin_B13)
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
// X-skin: X9=PB6=SCL, X10=PB7=SDA
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
// Y-skin: Y9=PB10=SCL, Y10=PB11=SDA
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// SPI busses
#define MICROPY_HW_SPI1_NAME "X"
#define MICROPY_HW_SPI1_NSS (pin_A4) // X5
#define MICROPY_HW_SPI1_SCK (pin_A5) // X6
#define MICROPY_HW_SPI1_MISO (pin_A6) // X7
#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8
#define MICROPY_HW_SPI2_NAME "Y"
#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5
#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6
#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7
#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8
// CAN busses
#define MICROPY_HW_CAN1_TX (pin_B9) // Y4
#define MICROPY_HW_CAN1_RX (pin_B8) // Y3
#define MICROPY_HW_CAN2_TX (pin_B13) // Y6
#define MICROPY_HW_CAN2_RX (pin_B12) // Y5
// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
#define MICROPY_HW_USRSW_PIN (pin_A13)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED_INVERTED (1) // LEDs are on when pin is driven low
#define MICROPY_HW_LED1 (pin_A8) // R1 - red
#define MICROPY_HW_LED2 (pin_A10) // R2 - red
#define MICROPY_HW_LED3 (pin_C4) // G1 - green
#define MICROPY_HW_LED4 (pin_C5) // G2 - green
#define MICROPY_HW_LED1_PWM { TIM1, 1, TIM_CHANNEL_1, GPIO_AF1_TIM1 }
#define MICROPY_HW_LED2_PWM { TIM1, 1, TIM_CHANNEL_3, GPIO_AF1_TIM1 }
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLDOWN)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_SET)
// USB VBUS detect pin
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
// MMA accelerometer config
#define MICROPY_HW_MMA_AVDD_PIN (pin_B5)