circuitpython/ports/atmel-samd/boards/feather_m0_adalogger/mpconfigboard.h

// LEDs
#define MICROPY_HW_LED_STATUS   (&pin_PA17)

#define MICROPY_HW_BOARD_NAME "Adafruit Feather M0 Adalogger"
#define MICROPY_HW_MCU_NAME "samd21g18"

#define DEFAULT_I2C_BUS_SDA (&pin_PA22)
#define DEFAULT_I2C_BUS_SCL (&pin_PA23)

#define DEFAULT_SPI_BUS_SCK (&pin_PB11)
#define DEFAULT_SPI_BUS_MOSI (&pin_PB10)
#define DEFAULT_SPI_BUS_MISO (&pin_PA12)

#define DEFAULT_UART_BUS_RX (&pin_PA11)
#define DEFAULT_UART_BUS_TX (&pin_PA10)

// USB is always used internally so skip the pin objects for it.
#define IGNORE_PIN_PA24     1
#define IGNORE_PIN_PA25     1
[atmel-samd] add adalogger board definitions 2016-10-16 12:19:08 -04:00			`// LEDs`
Rework safe mode and have heap overwrite trigger it. This creates a common safe mode mechanic that ports can share. As a result, the nRF52 now has safe mode support as well. The common safe mode adds a 700ms delay at startup where a reset during that window will cause a reset into safe mode. This window is designated by a yellow status pixel and flashing the single led three times. A couple NeoPixel fixes are included for the nRF52 as well. Fixes #1034. Fixes #990. Fixes #615. 2018-12-06 17:24:20 -05:00			`#define MICROPY_HW_LED_STATUS (&pin_PA17)`

[atmel-samd] add adalogger board definitions 2016-10-16 12:19:08 -04:00			`#define MICROPY_HW_BOARD_NAME "Adafruit Feather M0 Adalogger"`
			`#define MICROPY_HW_MCU_NAME "samd21g18"`
atmel-samd: Support auto-reset based on USB write activity. It will soft-reboot micropython after a burst of writes to the file system. This means that after you save files on your computer they will be automatically rerun. This can be disabled in the build by unsetting AUTORESET_TIMER in mpconfigboard.h. Using the REPL will also prevent the soft resets until you reset with CTRL-D manually. 2016-10-25 17:27:59 -04:00
Update mpconfigboard.h 2021-04-17 21:15:04 -04:00			`#define DEFAULT_I2C_BUS_SDA (&pin_PA22)`
			`#define DEFAULT_I2C_BUS_SCL (&pin_PA23)`
spi on much 2018-05-16 15:25:24 -04:00
SPI for all boards 2018-05-16 15:36:36 -04:00			`#define DEFAULT_SPI_BUS_SCK (&pin_PB11)`
spi on much 2018-05-16 15:25:24 -04:00			`#define DEFAULT_SPI_BUS_MOSI (&pin_PB10)`
			`#define DEFAULT_SPI_BUS_MISO (&pin_PA12)`
arduino, circuitplayground, feather boards 2018-05-17 13:42:08 -04:00
			`#define DEFAULT_UART_BUS_RX (&pin_PA11)`
			`#define DEFAULT_UART_BUS_TX (&pin_PA10)`
Turn off USB pin objects since they are always used for USB. 2018-06-06 15:07:28 -04:00
			`// USB is always used internally so skip the pin objects for it.`
			`#define IGNORE_PIN_PA24 1`
			`#define IGNORE_PIN_PA25 1`