Update README

README.md

@@ -2,6 +2,7 @@
 
 **Note**: I did not write this driver. I only modified it to clean up compiler warnings/errors. The original can be found here:
 (http://www.librecalc.com/en/wp-content/uploads/sites/4/2014/10/sharp.c)
+
 More information can be found here:
 (http://www.librecalc.com/en/downloads/)
 
@@ -9,29 +10,38 @@ This driver is for the LS027B7DH01. It *should* work with other Sharp Mem LCD di
 
 ## Hookup Guide
 Connect the following pins:
-| Display |   RasPi   |
-| ------- | --------- |
-| VIN     | 3.3V      |
-| 3V3     | N/C       |
-| GND     | GND       |
-| SCLK    | 11 (SCLK) |
-| MOSI    | 10 (MOSI) |
-| CS      | 23        |
-| EXTMD   | 3.3V      |
-| DISP    | 24        |
-| EXTIN   | 25        |
+
+Display | RasPi
+------- | ---------
+VIN     | 3.3V      
+3V3     | N/C       
+GND     | GND       
+SCLK    | 11 (SCLK) 
+MOSI    | 10 (MOSI) 
+CS      | 23        
+EXTMD   | 3.3V      
+DISP    | 24        
+EXTIN   | 25        
 
 ## Compile/Install the driver
 Verify that you have the linux kernel headers for your platform. For the RasPi these can be obtained by:
-```sudo apt-get install raspberrypi-kernel-headers```
+```
+sudo apt-get install raspberrypi-kernel-headers
+```
 or more generally:
-```sudo apt-get install linux-headers-$(uname -r)```
+```
+sudo apt-get install linux-headers-$(uname -r)
+```
 
 To compile the driver, run:
-```make```
+```
+make
+```
 
 To install the driver, run:
-```sudo make modules_install```
+```
+sudo make modules_install
+```
 
 If you want the module to load at boot you'll need to add it to the /etc/modules file, like:
 ```
@@ -43,20 +53,28 @@ sharp
 
 ## Compile/Install the Device Tree Overlay
 The included sharp.dts file is for the Raspberry Pi Zero W. To compile it, run:
-```dtc -@ -I dts -O dtb -o sharp.dtbo sharp.dts```
+```
+dtc -@ -I dts -O dtb -o sharp.dtbo sharp.dts
+```
 
 To load it at runtime, copy it to /boot/overlays:
-```sudo cp sharp.dtbo /boot/overlays```
+```
+sudo cp sharp.dtbo /boot/overlays
+```
 
 And then add the following line to /boot/config.txt:
-```dtoverlay=sharp```
+```
+dtoverlay=sharp
+```
 
 ## Console on Display
 If you want the boot console to show up on the display, you'll need to append `fbcon=map:10` to /boot/cmdline.txt after *rootwait*, like:
-```... rootwait ... fbcon=map:10```
+```
+... rootwait ... fbcon=map:10
+```
 
 To make sure the console fits on screen, uncomment the following lines in /boot/config.txt and set the resolution appropriately:
 ```
 framebuffer_width=400
 framebuffer_height=240
-```
+```