a1fbb1980c
This is a MicroPython-specific module that existed to support the old version of uasyncio. It's undocumented and not enabled on all ports and takes up code size unnecessarily. Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
70 lines
3.1 KiB
C
70 lines
3.1 KiB
C
// MCU config
|
|
#define MICROPY_HW_BOARD_NAME "EK-RA4W1"
|
|
#define MICROPY_HW_MCU_NAME "RA4W1"
|
|
#define MICROPY_HW_MCU_SYSCLK 48000000
|
|
#define MICROPY_HW_MCU_PCLK 48000000
|
|
|
|
// module config
|
|
#define MICROPY_EMIT_THUMB (1)
|
|
#define MICROPY_EMIT_INLINE_THUMB (1)
|
|
#define MICROPY_PY_BUILTINS_COMPLEX (1)
|
|
#define MICROPY_PY_GENERATOR_PEND_THROW (1)
|
|
#define MICROPY_PY_MATH (1)
|
|
#define MICROPY_PY_HEAPQ (1)
|
|
#define MICROPY_PY_THREAD (0) // disable ARM_THUMB_FP using vldr due to RA has single float only
|
|
|
|
// peripheral config
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_RTC_SOURCE (1) // 0: subclock, 1: LOCO (32.768khz)
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
|
|
|
|
// board config
|
|
|
|
// UART
|
|
// #define MICROPY_HW_UART0_TX (pin_P101) // Disable (Conflict with PMOD)
|
|
// #define MICROPY_HW_UART0_RX (pin_P100) // Disable (Conflict with PMOD)
|
|
// #define MICROPY_HW_UART0_CTS (pin_P103) // Disable (Conflict with PMOD)
|
|
#define MICROPY_HW_UART1_TX (pin_P213)
|
|
#define MICROPY_HW_UART1_RX (pin_P212)
|
|
// #define MICROPY_HW_UART1_CTS (pin_P101) // Disable (Conflict with PMOD)
|
|
#define MICROPY_HW_UART4_TX (pin_P205) // REPL
|
|
#define MICROPY_HW_UART4_RX (pin_P206) // REPL
|
|
// #define MICROPY_HW_UART4_CTS (pin_P407) // Conflict with PMOD1-IO1
|
|
#define MICROPY_HW_UART9_TX (pin_P109)
|
|
#define MICROPY_HW_UART9_RX (pin_P110)
|
|
// #define MICROPY_HW_UART9_CTS (pin_P108) // NC
|
|
#define MICROPY_HW_UART_REPL HW_UART_4
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C
|
|
#define MICROPY_HW_I2C0_SCL (pin_P204) // Note that conflict with PMOD IO0
|
|
#define MICROPY_HW_I2C0_SDA (pin_P407) // Note that conflict with PMOD IO1
|
|
// #define MICROPY_HW_I2C1_SCL (pin_P100) // Disable (Conflict with SPI0)
|
|
// #define MICROPY_HW_I2C1_SDA (pin_P101) // Disable (Conflict with SPI0)
|
|
|
|
// SPI
|
|
#define MICROPY_HW_SPI0_SSL (pin_P103) // PMOD
|
|
#define MICROPY_HW_SPI0_RSPCK (pin_P102) // PMOD
|
|
#define MICROPY_HW_SPI0_MISO (pin_P100) // PMOD
|
|
#define MICROPY_HW_SPI0_MOSI (pin_P101) // PMOD
|
|
// #define MICROPY_HW_SPI1_SSL (pin_P108) // Disable (vector not registered)
|
|
// #define MICROPY_HW_SPI1_RSPCK (pin_P111) // Disable (vector not registered)
|
|
// #define MICROPY_HW_SPI1_MISO (pin_P110) // Disable (vector not registered)
|
|
// #define MICROPY_HW_SPI1_MOSI (pin_P109) // Disable (vector not registered)
|
|
|
|
// Switch
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_USRSW_PIN (pin_P402)
|
|
#define MICROPY_HW_USRSW_PULL (MP_HAL_PIN_PULL_NONE)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (MP_HAL_PIN_TRIGGER_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_P106)
|
|
#define MICROPY_HW_LED2 (pin_P404)
|
|
#define MICROPY_HW_LED_ON(pin) mp_hal_pin_low(pin)
|
|
#define MICROPY_HW_LED_OFF(pin) mp_hal_pin_high(pin)
|
|
#define MICROPY_HW_LED_TOGGLE(pin) mp_hal_pin_toggle(pin)
|