circuitpython/ports/stm/peripherals/stm32h7/clocks.c

116 lines
4.8 KiB
C

/*
* This file is part of the Micro Python project, http://micropython.org/
*
* The MIT License (MIT)
*
* Copyright (c) 2020 Lucian Copeland for Adafruit Industries
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
#include "stm32h7xx_hal.h"
#include "supervisor/shared/safe_mode.h"
#include <stdbool.h>
// H7 Series
#ifdef STM32H743xx
#include "stm32h7/stm32h743xx/clocks.h"
#endif
void stm32_peripherals_clocks_init(void) {
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
// Set voltage scaling in accordance with system clock speed
HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);
__HAL_PWR_VOLTAGESCALING_CONFIG(CPY_CLK_VSCALE);
while (!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {
}
// Configure LSE Drive
HAL_PWR_EnableBkUpAccess();
__HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
// Set up primary PLL and HSE clocks
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
#if (BOARD_HAS_LOW_SPEED_CRYSTAL)
RCC_OscInitStruct.OscillatorType |= RCC_OSCILLATORTYPE_LSE;
RCC_OscInitStruct.LSEState = RCC_LSE_ON;
#else
RCC_OscInitStruct.OscillatorType |= RCC_OSCILLATORTYPE_LSI;
RCC_OscInitStruct.LSIState = RCC_LSI_ON;
#endif
#if (CPY_CLK_USB_USES_AUDIOPLL) // Not actually audio PLL in this case, swap macro?
RCC_OscInitStruct.OscillatorType |= RCC_OSCILLATORTYPE_HSI48;
RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
#endif
RCC_OscInitStruct.HSEState = BOARD_HSE_SOURCE;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = HSE_VALUE / 2000000;
RCC_OscInitStruct.PLL.PLLN = CPY_CLK_PLLN;
RCC_OscInitStruct.PLL.PLLP = CPY_CLK_PLLP;
RCC_OscInitStruct.PLL.PLLQ = CPY_CLK_PLLQ;
RCC_OscInitStruct.PLL.PLLR = 2;
RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_1;
RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE;
RCC_OscInitStruct.PLL.PLLFRACN = 0;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
// Clock issues are too problematic to even attempt recovery.
// If you end up here, check whether your LSE settings match your board.
while (1) {
;
}
}
// Configure bus clock sources and divisors
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
| RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2
| RCC_CLOCKTYPE_D3PCLK1 | RCC_CLOCKTYPE_D1PCLK1;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.AHBCLKDivider = CPY_CLK_AHBDIV;
RCC_ClkInitStruct.APB1CLKDivider = CPY_CLK_APB1DIV;
RCC_ClkInitStruct.APB2CLKDivider = CPY_CLK_APB2DIV;
RCC_ClkInitStruct.APB3CLKDivider = CPY_CLK_APB3DIV;
RCC_ClkInitStruct.APB4CLKDivider = CPY_CLK_APB4DIV;
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, CPY_CLK_FLASH_LATENCY);
// Set up non-bus peripherals
// TODO: I2S settings go here
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC | RCC_PERIPHCLK_USART3
| RCC_PERIPHCLK_USB;
#if (BOARD_HAS_LOW_SPEED_CRYSTAL)
PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
#else
PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;
#endif
PeriphClkInitStruct.Usart234578ClockSelection = RCC_USART234578CLKSOURCE_D2PCLK1;
#if (CPY_CLK_USB_USES_AUDIOPLL) // Not actually audio PLL in this case, swap macro?
PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
#else
PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL;
#endif
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
// Enable USB Voltage detector
HAL_PWREx_EnableUSBVoltageDetector();
}