circuitpython/ports/stm32/boards/STM32F429DISC/mpconfigboard.h

145 lines
5.3 KiB
C

#define MICROPY_HW_BOARD_NAME "F429I-DISCO"
#define MICROPY_HW_MCU_NAME "STM32F429"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_USB (1)
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
#define MICROPY_HW_UART_REPL PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD 115200
// UART config
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART2_TX (pin_D8)
#define MICROPY_HW_UART2_RX (pin_D9)
// I2C busses
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_C9)
// SPI busses
//#define MICROPY_HW_SPI1_NSS (pin_A4)
//#define MICROPY_HW_SPI1_SCK (pin_A5)
//#define MICROPY_HW_SPI1_MISO (pin_A6)
//#define MICROPY_HW_SPI1_MOSI (pin_A7)
#if defined(USE_USB_HS_IN_FS)
// The HS USB uses B14 & B15 for D- and D+
#else
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
#endif
//#define MICROPY_HW_SPI4_NSS (pin_E11)
//#define MICROPY_HW_SPI4_SCK (pin_E12)
//#define MICROPY_HW_SPI4_MISO (pin_E13)
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
#define MICROPY_HW_SPI5_NSS (pin_F6)
#define MICROPY_HW_SPI5_SCK (pin_F7)
#define MICROPY_HW_SPI5_MISO (pin_F8)
#define MICROPY_HW_SPI5_MOSI (pin_F9)
//#define MICROPY_HW_SPI6_NSS (pin_G8)
//#define MICROPY_HW_SPI6_SCK (pin_G13)
//#define MICROPY_HW_SPI6_MISO (pin_G12)
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
// CAN busses
#define MICROPY_HW_CAN1_TX (pin_B9)
#define MICROPY_HW_CAN1_RX (pin_B8)
#define MICROPY_HW_CAN2_TX (pin_B13)
#define MICROPY_HW_CAN2_RX (pin_B12)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_G14) // red
#define MICROPY_HW_LED2 (pin_G13) // green
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config
#define MICROPY_HW_USB_HS (1)
#define MICROPY_HW_USB_HS_IN_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_B13)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_B12)
// SDRAM
#define MICROPY_HW_SDRAM_SIZE (64 / 8 * 1024 * 1024) // 64 Mbit
#define MICROPY_HW_SDRAM_STARTUP_TEST (1)
#define MICROPY_HEAP_START sdram_start()
#define MICROPY_HEAP_END sdram_end()
// Timing configuration for 90 Mhz (11.90ns) of SD clock frequency (180Mhz/2)
#define MICROPY_HW_SDRAM_TIMING_TMRD (2)
#define MICROPY_HW_SDRAM_TIMING_TXSR (7)
#define MICROPY_HW_SDRAM_TIMING_TRAS (4)
#define MICROPY_HW_SDRAM_TIMING_TRC (7)
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
#define MICROPY_HW_SDRAM_TIMING_TRP (2)
#define MICROPY_HW_SDRAM_TIMING_TRCD (2)
#define MICROPY_HW_SDRAM_REFRESH_RATE (64) // ms
#define MICROPY_HW_SDRAM_BURST_LENGTH 2
#define MICROPY_HW_SDRAM_CAS_LATENCY 3
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM 8
#define MICROPY_HW_SDRAM_ROW_BITS_NUM 12
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH 16
#define MICROPY_HW_SDRAM_INTERN_BANKS_NUM 4
#define MICROPY_HW_SDRAM_CLOCK_PERIOD 2
#define MICROPY_HW_SDRAM_RPIPE_DELAY 1
#define MICROPY_HW_SDRAM_RBURST (0)
#define MICROPY_HW_SDRAM_WRITE_PROTECTION (0)
#define MICROPY_HW_SDRAM_AUTOREFRESH_NUM (4)
#define MICROPY_HW_FMC_SDCKE1 (pin_B5)
#define MICROPY_HW_FMC_SDNE1 (pin_B6)
#define MICROPY_HW_FMC_SDCLK (pin_G8)
#define MICROPY_HW_FMC_SDNCAS (pin_G15)
#define MICROPY_HW_FMC_SDNRAS (pin_F11)
#define MICROPY_HW_FMC_SDNWE (pin_C0)
#define MICROPY_HW_FMC_BA0 (pin_G4)
#define MICROPY_HW_FMC_BA1 (pin_G5)
#define MICROPY_HW_FMC_NBL0 (pin_E0)
#define MICROPY_HW_FMC_NBL1 (pin_E1)
#define MICROPY_HW_FMC_A0 (pin_F0)
#define MICROPY_HW_FMC_A1 (pin_F1)
#define MICROPY_HW_FMC_A2 (pin_F2)
#define MICROPY_HW_FMC_A3 (pin_F3)
#define MICROPY_HW_FMC_A4 (pin_F4)
#define MICROPY_HW_FMC_A5 (pin_F5)
#define MICROPY_HW_FMC_A6 (pin_F12)
#define MICROPY_HW_FMC_A7 (pin_F13)
#define MICROPY_HW_FMC_A8 (pin_F14)
#define MICROPY_HW_FMC_A9 (pin_F15)
#define MICROPY_HW_FMC_A10 (pin_G0)
#define MICROPY_HW_FMC_A11 (pin_G1)
#define MICROPY_HW_FMC_D0 (pin_D14)
#define MICROPY_HW_FMC_D1 (pin_D15)
#define MICROPY_HW_FMC_D2 (pin_D0)
#define MICROPY_HW_FMC_D3 (pin_D1)
#define MICROPY_HW_FMC_D4 (pin_E7)
#define MICROPY_HW_FMC_D5 (pin_E8)
#define MICROPY_HW_FMC_D6 (pin_E9)
#define MICROPY_HW_FMC_D7 (pin_E10)
#define MICROPY_HW_FMC_D8 (pin_E11)
#define MICROPY_HW_FMC_D9 (pin_E12)
#define MICROPY_HW_FMC_D10 (pin_E13)
#define MICROPY_HW_FMC_D11 (pin_E14)
#define MICROPY_HW_FMC_D12 (pin_E15)
#define MICROPY_HW_FMC_D13 (pin_D8)
#define MICROPY_HW_FMC_D14 (pin_D9)
#define MICROPY_HW_FMC_D15 (pin_D10)