circuitpython/ports/stm32/boards/ARDUINO_GIGA/mpconfigboard.h

319 lines
13 KiB
C

/*
* This file is part of the MicroPython project, http://micropython.org/
* The MIT License (MIT)
* Copyright (c) 2023 Arduino SA
*/
#define MICROPY_HW_BOARD_NAME "GIGA"
#define MICROPY_HW_MCU_NAME "STM32H747"
#define MICROPY_PY_SYS_PLATFORM "Giga"
#define MICROPY_HW_FLASH_FS_LABEL "Giga"
#define MICROPY_OBJ_REPR (MICROPY_OBJ_REPR_C)
#define UINT_FMT "%u"
#define INT_FMT "%d"
typedef int mp_int_t; // must be pointer size
typedef unsigned int mp_uint_t; // must be pointer size
#define MICROPY_FATFS_EXFAT (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_ADC (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SDCARD (0)
#define MICROPY_HW_ENABLE_MMCARD (0)
// Flash storage config
#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1)
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
#define MICROPY_BOARD_STARTUP GIGA_board_startup
void GIGA_board_startup(void);
#define MICROPY_BOARD_EARLY_INIT GIGA_board_early_init
void GIGA_board_early_init(void);
#define MICROPY_BOARD_ENTER_BOOTLOADER(nargs, args) GIGA_board_enter_bootloader()
void GIGA_board_enter_bootloader(void);
void GIGA_board_low_power(int mode);
#define MICROPY_BOARD_LEAVE_STOP GIGA_board_low_power(0);
#define MICROPY_BOARD_ENTER_STOP GIGA_board_low_power(1);
#define MICROPY_BOARD_ENTER_STANDBY GIGA_board_low_power(2);
void GIGA_board_osc_enable(int enable);
#define MICROPY_BOARD_OSC_ENABLE GIGA_board_osc_enable(1);
#define MICROPY_BOARD_OSC_DISABLE GIGA_board_osc_enable(0);
// PLL1 480MHz/48MHz SDMMC and FDCAN
// USB and RNG are clocked from the HSI48
#define MICROPY_HW_CLK_PLLM (4)
#define MICROPY_HW_CLK_PLLN (240)
#define MICROPY_HW_CLK_PLLP (2)
#define MICROPY_HW_CLK_PLLQ (20)
#define MICROPY_HW_CLK_PLLR (2)
#define MICROPY_HW_CLK_PLLVCI (RCC_PLL1VCIRANGE_2)
#define MICROPY_HW_CLK_PLLVCO (RCC_PLL1VCOWIDE)
#define MICROPY_HW_CLK_PLLFRAC (0)
// PLL2 200MHz for FMC and QSPI.
#define MICROPY_HW_CLK_PLL2M (4)
#define MICROPY_HW_CLK_PLL2N (100)
#define MICROPY_HW_CLK_PLL2P (2)
#define MICROPY_HW_CLK_PLL2Q (2)
#define MICROPY_HW_CLK_PLL2R (2)
#define MICROPY_HW_CLK_PLL2VCI (RCC_PLL2VCIRANGE_2)
#define MICROPY_HW_CLK_PLL2VCO (RCC_PLL2VCOWIDE)
#define MICROPY_HW_CLK_PLL2FRAC (0)
// PLL3 160MHz for ADC and SPI123
#define MICROPY_HW_CLK_PLL3M (4)
#define MICROPY_HW_CLK_PLL3N (80)
#define MICROPY_HW_CLK_PLL3P (2)
#define MICROPY_HW_CLK_PLL3Q (2)
#define MICROPY_HW_CLK_PLL3R (2)
#define MICROPY_HW_CLK_PLL3VCI (RCC_PLL3VCIRANGE_2)
#define MICROPY_HW_CLK_PLL3VCO (RCC_PLL3VCOWIDE)
#define MICROPY_HW_CLK_PLL3FRAC (0)
// HSE in BYPASS mode.
#define MICROPY_HW_CLK_USE_BYPASS (0)
// Bus clock divider values
#define MICROPY_HW_CLK_AHB_DIV (RCC_HCLK_DIV2)
#define MICROPY_HW_CLK_APB1_DIV (RCC_APB1_DIV2)
#define MICROPY_HW_CLK_APB2_DIV (RCC_APB2_DIV2)
#define MICROPY_HW_CLK_APB3_DIV (RCC_APB3_DIV2)
#define MICROPY_HW_CLK_APB4_DIV (RCC_APB4_DIV2)
// Peripheral clock sources
#define MICROPY_HW_RCC_HSI48_STATE (RCC_HSI48_ON)
#define MICROPY_HW_RCC_USB_CLKSOURCE (RCC_USBCLKSOURCE_HSI48)
#define MICROPY_HW_RCC_RTC_CLKSOURCE (RCC_RTCCLKSOURCE_LSI)
#define MICROPY_HW_RCC_FMC_CLKSOURCE (RCC_FMCCLKSOURCE_PLL2)
#define MICROPY_HW_RCC_RNG_CLKSOURCE (RCC_RNGCLKSOURCE_HSI48)
#define MICROPY_HW_RCC_ADC_CLKSOURCE (RCC_ADCCLKSOURCE_PLL3)
#define MICROPY_HW_RCC_SDMMC_CLKSOURCE (RCC_SDMMCCLKSOURCE_PLL)
#define MICROPY_HW_RCC_FDCAN_CLKSOURCE (RCC_FDCANCLKSOURCE_PLL)
#define MICROPY_HW_RCC_SPI123_CLKSOURCE (RCC_SPI123CLKSOURCE_PLL3)
#define MICROPY_HW_RCC_I2C123_CLKSOURCE (RCC_I2C123CLKSOURCE_D2PCLK1)
#define MICROPY_HW_RCC_QSPI_CLKSOURCE (RCC_QSPICLKSOURCE_PLL2)
// SMPS configuration
#define MICROPY_HW_PWR_SMPS_CONFIG (PWR_LDO_SUPPLY)
// There is an external 32kHz oscillator
#define RTC_ASYNCH_PREDIV (0)
#define RTC_SYNCH_PREDIV (0x7fff)
#define MICROPY_HW_RTC_USE_BYPASS (0)
#define MICROPY_HW_RTC_USE_US (1)
#define MICROPY_HW_RTC_USE_CALOUT (1)
#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
// QSPI flash #1 for storage
#define MICROPY_HW_QSPI_PRESCALER (2) // 100MHz
#define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (27)
// Reserve 1MiB at the end for compatibility with alternate firmware that places WiFi blob here.
#define MICROPY_HW_SPIFLASH_SIZE_BITS (120 * 1024 * 1024)
#define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS)
#define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK)
#define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0)
#define MICROPY_HW_QSPIFLASH_IO1 (pyb_pin_QSPI2_D1)
#define MICROPY_HW_QSPIFLASH_IO2 (pyb_pin_QSPI2_D2)
#define MICROPY_HW_QSPIFLASH_IO3 (pyb_pin_QSPI2_D3)
// SPI flash #1, block device config
extern const struct _mp_spiflash_config_t spiflash_config;
extern struct _spi_bdev_t spi_bdev;
#define MICROPY_HW_BDEV_IOCTL(op, arg) ( \
(op) == BDEV_IOCTL_NUM_BLOCKS ? (MICROPY_HW_SPIFLASH_SIZE_BITS / 8 / FLASH_BLOCK_SIZE) : \
(op) == BDEV_IOCTL_INIT ? spi_bdev_ioctl(&spi_bdev, (op), (uint32_t)&spiflash_config) : \
spi_bdev_ioctl(&spi_bdev, (op), (arg)) \
)
#define MICROPY_HW_BDEV_READBLOCKS(dest, bl, n) spi_bdev_readblocks(&spi_bdev, (dest), (bl), (n))
#define MICROPY_HW_BDEV_WRITEBLOCKS(src, bl, n) spi_bdev_writeblocks(&spi_bdev, (src), (bl), (n))
#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev)
#endif
// 4 wait states
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_2
// UART config
#define MICROPY_HW_UART1_TX (pyb_pin_UART1_TX)
#define MICROPY_HW_UART1_RX (pyb_pin_UART1_RX)
#define MICROPY_HW_UART_REPL PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD 115200
#define MICROPY_HW_UART2_TX (pyb_pin_UART2_TX)
#define MICROPY_HW_UART2_RX (pyb_pin_UART2_RX)
#define MICROPY_HW_UART4_TX (pyb_pin_UART4_TX)
#define MICROPY_HW_UART4_RX (pyb_pin_UART4_RX)
#define MICROPY_HW_UART6_TX (pyb_pin_UART6_TX)
#define MICROPY_HW_UART6_RX (pyb_pin_UART6_RX)
#define MICROPY_HW_UART7_TX (pyb_pin_BT_TXD)
#define MICROPY_HW_UART7_RX (pyb_pin_BT_RXD)
#define MICROPY_HW_UART7_RTS (pyb_pin_BT_RTS)
#define MICROPY_HW_UART7_CTS (pyb_pin_BT_CTS)
// I2C busses
#define MICROPY_HW_I2C1_SCL (pyb_pin_I2C1_SCL)
#define MICROPY_HW_I2C1_SDA (pyb_pin_I2C1_SDA)
#define MICROPY_HW_I2C2_SCL (pyb_pin_I2C2_SCL)
#define MICROPY_HW_I2C2_SDA (pyb_pin_I2C2_SDA)
#define MICROPY_HW_I2C4_SCL (pyb_pin_I2C4_SCL)
#define MICROPY_HW_I2C4_SDA (pyb_pin_I2C4_SDA)
// SPI config
// #define MICROPY_HW_SPI1_NSS (pyb_pin_SPI1_NSS)
#define MICROPY_HW_SPI1_SCK (pyb_pin_SPI1_SCK)
#define MICROPY_HW_SPI1_MISO (pyb_pin_SPI1_MISO)
#define MICROPY_HW_SPI1_MOSI (pyb_pin_SPI1_MOSI)
#define MICROPY_HW_SPI5_NSS (pyb_pin_SPI5_NSS)
#define MICROPY_HW_SPI5_SCK (pyb_pin_SPI5_SCK)
#define MICROPY_HW_SPI5_MISO (pyb_pin_SPI5_MISO)
#define MICROPY_HW_SPI5_MOSI (pyb_pin_SPI5_MOSI)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLDOWN)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pyb_pin_LEDR) // red
#define MICROPY_HW_LED2 (pyb_pin_LEDG) // green
#define MICROPY_HW_LED3 (pyb_pin_LEDB) // yellow
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
// WiFi SDMMC
#define MICROPY_HW_SDIO_SDMMC (1)
#define MICROPY_HW_SDIO_CK (pyb_pin_WL_SDIO_CLK)
#define MICROPY_HW_SDIO_CMD (pyb_pin_WL_SDIO_CMD)
#define MICROPY_HW_SDIO_D0 (pyb_pin_WL_SDIO_0)
#define MICROPY_HW_SDIO_D1 (pyb_pin_WL_SDIO_1)
#define MICROPY_HW_SDIO_D2 (pyb_pin_WL_SDIO_2)
#define MICROPY_HW_SDIO_D3 (pyb_pin_WL_SDIO_3)
// CYW43 config
#define CYW43_WIFI_NVRAM_INCLUDE_FILE "wifi_nvram_1dx.h"
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (1024)
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (1024)
#define MICROPY_HW_USB_CDC_1200BPS_TOUCH (1)
// Bluetooth config
#define MICROPY_HW_BLE_UART_ID (PYB_UART_7)
#define MICROPY_HW_BLE_UART_BAUDRATE (115200)
#define MICROPY_HW_BLE_UART_BAUDRATE_SECONDARY (3000000)
// SDRAM
#define MICROPY_HW_SDRAM_SIZE (64 / 8 * 1024 * 1024) // 64 Mbit
#define MICROPY_HW_SDRAM_STARTUP_TEST (1)
#define MICROPY_HW_SDRAM_TEST_FAIL_ON_ERROR (true)
// Timing configuration for 200MHz/2=100MHz (10ns)
#define MICROPY_HW_SDRAM_CLOCK_PERIOD 2
#define MICROPY_HW_SDRAM_CAS_LATENCY 2
#define MICROPY_HW_SDRAM_FREQUENCY (100000) // 100 MHz
#define MICROPY_HW_SDRAM_TIMING_TMRD (2)
#define MICROPY_HW_SDRAM_TIMING_TXSR (7)
#define MICROPY_HW_SDRAM_TIMING_TRAS (5)
#define MICROPY_HW_SDRAM_TIMING_TRC (7)
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
#define MICROPY_HW_SDRAM_TIMING_TRP (3)
#define MICROPY_HW_SDRAM_TIMING_TRCD (3)
#define MICROPY_HW_SDRAM_ROW_BITS_NUM 12
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH 16
#define MICROPY_HW_SDRAM_REFRESH_CYCLES 4096
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM 8
#define MICROPY_HW_SDRAM_INTERN_BANKS_NUM 4
#define MICROPY_HW_SDRAM_RPIPE_DELAY 0
#define MICROPY_HW_SDRAM_RBURST (1)
#define MICROPY_HW_SDRAM_WRITE_PROTECTION (0)
#define MICROPY_HW_SDRAM_AUTOREFRESH_NUM (8)
#define MICROPY_HW_SDRAM_BURST_LENGTH 1
#define MICROPY_HW_SDRAM_REFRESH_RATE (64) // ms
// SDRAM configuration
#define MICROPY_HW_FMC_SDCKE0 (pin_H2)
#define MICROPY_HW_FMC_SDNE0 (pin_H3)
#define MICROPY_HW_FMC_SDNBL0 (pin_E0)
#define MICROPY_HW_FMC_SDNBL1 (pin_E1)
#define MICROPY_HW_FMC_SDCLK (pin_G8)
#define MICROPY_HW_FMC_SDNCAS (pin_G15)
#define MICROPY_HW_FMC_SDNRAS (pin_F11)
#define MICROPY_HW_FMC_SDNWE (pin_H5)
#define MICROPY_HW_FMC_BA0 (pin_G4)
#define MICROPY_HW_FMC_BA1 (pin_G5)
#define MICROPY_HW_FMC_NBL0 (pin_E0)
#define MICROPY_HW_FMC_NBL1 (pin_E1)
#define MICROPY_HW_FMC_A0 (pin_F0)
#define MICROPY_HW_FMC_A1 (pin_F1)
#define MICROPY_HW_FMC_A2 (pin_F2)
#define MICROPY_HW_FMC_A3 (pin_F3)
#define MICROPY_HW_FMC_A4 (pin_F4)
#define MICROPY_HW_FMC_A5 (pin_F5)
#define MICROPY_HW_FMC_A6 (pin_F12)
#define MICROPY_HW_FMC_A7 (pin_F13)
#define MICROPY_HW_FMC_A8 (pin_F14)
#define MICROPY_HW_FMC_A9 (pin_F15)
#define MICROPY_HW_FMC_A10 (pin_G0)
#define MICROPY_HW_FMC_A11 (pin_G1)
#define MICROPY_HW_FMC_A12 (pin_G2)
#define MICROPY_HW_FMC_D0 (pin_D14)
#define MICROPY_HW_FMC_D1 (pin_D15)
#define MICROPY_HW_FMC_D2 (pin_D0)
#define MICROPY_HW_FMC_D3 (pin_D1)
#define MICROPY_HW_FMC_D4 (pin_E7)
#define MICROPY_HW_FMC_D5 (pin_E8)
#define MICROPY_HW_FMC_D6 (pin_E9)
#define MICROPY_HW_FMC_D7 (pin_E10)
#define MICROPY_HW_FMC_D8 (pin_E11)
#define MICROPY_HW_FMC_D9 (pin_E12)
#define MICROPY_HW_FMC_D10 (pin_E13)
#define MICROPY_HW_FMC_D11 (pin_E14)
#define MICROPY_HW_FMC_D12 (pin_E15)
#define MICROPY_HW_FMC_D13 (pin_D8)
#define MICROPY_HW_FMC_D14 (pin_D9)
#define MICROPY_HW_FMC_D15 (pin_D10)
#define MICROPY_HW_USB_VID 0x2341
#define MICROPY_HW_USB_PID 0x0566
#define MICROPY_HW_USB_PID_CDC_MSC (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC_HID (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_MSC (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC2_MSC (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC2 (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC3 (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC3_MSC (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC_MSC_HID (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC2_MSC_HID (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_PID_CDC3_MSC_HID (MICROPY_HW_USB_PID)
#define MICROPY_HW_USB_LANGID_STRING 0x409
#define MICROPY_HW_USB_MANUFACTURER_STRING "Arduino"
#define MICROPY_HW_USB_PRODUCT_FS_STRING "Giga Virtual Comm Port in FS Mode"
#define MICROPY_HW_USB_PRODUCT_HS_STRING "Giga Virtual Comm Port in HS Mode"
#define MICROPY_HW_USB_INTERFACE_FS_STRING "Giga Interface"
#define MICROPY_HW_USB_INTERFACE_HS_STRING "Giga Interface"
#define MICROPY_HW_USB_CONFIGURATION_FS_STRING "Giga Config"
#define MICROPY_HW_USB_CONFIGURATION_HS_STRING "Giga Config"