92f54fe8d9
These were commented correctly by their colour, but in the wrong order with respect to the PCB silkscreen. Fixes issue #8054. Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
68 lines
2.7 KiB
C
68 lines
2.7 KiB
C
/* This file is part of the MicroPython project, http://micropython.org/
|
|
* MIT License; Copyright (c) 2019 Damien P. George
|
|
*/
|
|
|
|
#define MICROPY_HW_BOARD_NAME "NUCLEO-WB55"
|
|
#define MICROPY_HW_MCU_NAME "STM32WB55RGV6"
|
|
|
|
#define MICROPY_PY_PYB_LEGACY (0)
|
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
// There is an external 32kHz oscillator
|
|
#define RTC_ASYNCH_PREDIV (0)
|
|
#define RTC_SYNCH_PREDIV (0x7fff)
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
#define MICROPY_HW_RTC_USE_US (1)
|
|
|
|
// UART buses
|
|
#define MICROPY_HW_UART1_TX (pin_B6)
|
|
#define MICROPY_HW_UART1_RX (pin_B7)
|
|
#define MICROPY_HW_LPUART1_TX (pin_A2)
|
|
#define MICROPY_HW_LPUART1_RX (pin_A3)
|
|
// USART 1 is connected to the virtual com port on the ST-LINK
|
|
#define MICROPY_HW_UART_REPL PYB_UART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino D15, pin 3 on CN10
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9) // Arduino D14, pin 5 on CN10
|
|
#define MICROPY_HW_I2C3_SCL (pin_C0) // Arduino A0, pin 28 on CN7
|
|
#define MICROPY_HW_I2C3_SDA (pin_C1) // Arduino A1, pin 30 on CN7
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4) // Arduino D10 pin 17 on CN10
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12) // pin 16 on CN10
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13) // pin 30 on CN10
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14) // pin 28 on CN10
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15) // pin 26 on CN10
|
|
|
|
// User switch; pressing the button makes the input go low
|
|
#define MICROPY_HW_USRSW_PIN (pin_C4)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_B5) // blue
|
|
#define MICROPY_HW_LED2 (pin_B0) // green
|
|
#define MICROPY_HW_LED3 (pin_B1) // red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (512)
|
|
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (512)
|
|
|
|
// Bluetooth config
|
|
#define MICROPY_HW_BLE_UART_ID (0)
|
|
#define MICROPY_HW_BLE_UART_BAUDRATE (115200)
|