circuitpython/ports/stm32/usbd_conf.c
Damien George a03e6c1e05 stm32/irq: Define IRQ priorities directly as encoded hardware values.
For a given IRQn (eg UART) there's no need to carry around both a PRI and
SUBPRI value (eg IRQ_PRI_UART, IRQ_SUBPRI_UART).  Instead, the IRQ_PRI_UART
value has been changed in this patch to be the encoded hardware value,
using NVIC_EncodePriority.  This way the NVIC_SetPriority function can be
used directly, instead of going through HAL_NVIC_SetPriority which must do
extra processing to encode the PRI+SUBPRI.

For a priority grouping of 4 (4 bits for preempt priority, 0 bits for the
sub-priority), which is used in the stm32 port, the IRQ_PRI_xxx constants
remain unchanged in their value.

This patch also "fixes" the use of raise_irq_pri() which should be passed
the encoded value (but as mentioned above the unencoded value is the same
as the encoded value for priority grouping 4, so there was no bug from this
error).
2018-05-02 14:41:02 +10:00

693 lines
21 KiB
C

/*
* This file is part of the MicroPython project, http://micropython.org/
*/
/**
******************************************************************************
* @file USB_Device/CDC_Standalone/Src/usbd_conf.c
* @author MCD Application Team
* @version V1.0.1
* @date 26-February-2014
* @brief This file implements the USB Device library callbacks and MSP
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "usbd_core.h"
#include "py/obj.h"
#include "py/mphal.h"
#include "irq.h"
#include "usb.h"
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
#if MICROPY_HW_USB_FS
PCD_HandleTypeDef pcd_fs_handle;
#endif
#if MICROPY_HW_USB_HS
PCD_HandleTypeDef pcd_hs_handle;
#endif
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/*******************************************************************************
PCD BSP Routines
*******************************************************************************/
/**
* @brief Initializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd)
{
if(hpcd->Instance == USB_OTG_FS)
{
#if defined(STM32H7)
const uint32_t otg_alt = GPIO_AF10_OTG1_FS;
#else
const uint32_t otg_alt = GPIO_AF10_OTG_FS;
#endif
mp_hal_pin_config(pin_A11, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_A11, GPIO_SPEED_FREQ_VERY_HIGH);
mp_hal_pin_config(pin_A12, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_A12, GPIO_SPEED_FREQ_VERY_HIGH);
/* Configure VBUS Pin */
#if defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
// USB VBUS detect pin is always A9
mp_hal_pin_config(MICROPY_HW_USB_VBUS_DETECT_PIN, MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0);
#endif
#if defined(MICROPY_HW_USB_OTG_ID_PIN)
// USB ID pin is always A10
mp_hal_pin_config(MICROPY_HW_USB_OTG_ID_PIN, MP_HAL_PIN_MODE_ALT_OPEN_DRAIN, MP_HAL_PIN_PULL_UP, otg_alt);
#endif
#if defined(STM32H7)
// Keep USB clock running during sleep or else __WFI() will disable the USB
__HAL_RCC_USB2_OTG_FS_CLK_SLEEP_ENABLE();
__HAL_RCC_USB2_OTG_FS_ULPI_CLK_SLEEP_DISABLE();
#endif
/* Enable USB FS Clocks */
__USB_OTG_FS_CLK_ENABLE();
#if defined(STM32L4)
/* Enable VDDUSB */
if(__HAL_RCC_PWR_IS_CLK_DISABLED())
{
__HAL_RCC_PWR_CLK_ENABLE();
HAL_PWREx_EnableVddUSB();
__HAL_RCC_PWR_CLK_DISABLE();
}
else
{
HAL_PWREx_EnableVddUSB();
}
#endif
/* Set USBFS Interrupt priority */
NVIC_SetPriority(OTG_FS_IRQn, IRQ_PRI_OTG_FS);
/* Enable USBFS Interrupt */
HAL_NVIC_EnableIRQ(OTG_FS_IRQn);
}
#if MICROPY_HW_USB_HS
else if(hpcd->Instance == USB_OTG_HS)
{
#if MICROPY_HW_USB_HS_IN_FS
/* Configure USB FS GPIOs */
mp_hal_pin_config(pin_B14, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, GPIO_AF12_OTG_HS_FS);
mp_hal_pin_config_speed(pin_B14, GPIO_SPEED_FREQ_VERY_HIGH);
mp_hal_pin_config(pin_B15, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, GPIO_AF12_OTG_HS_FS);
mp_hal_pin_config_speed(pin_B15, GPIO_SPEED_FREQ_VERY_HIGH);
#if defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
/* Configure VBUS Pin */
mp_hal_pin_config(MICROPY_HW_USB_VBUS_DETECT_PIN, MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0);
#endif
#if defined(MICROPY_HW_USB_OTG_ID_PIN)
/* Configure ID pin */
mp_hal_pin_config(MICROPY_HW_USB_OTG_ID_PIN, MP_HAL_PIN_MODE_ALT_OPEN_DRAIN, MP_HAL_PIN_PULL_UP, GPIO_AF12_OTG_HS_FS);
#endif
/*
* Enable calling WFI and correct
* function of the embedded USB_FS_IN_HS phy
*/
__HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE();
__HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE();
/* Enable USB HS Clocks */
#if defined(STM32F723xx) || defined(STM32F733xx)
// Needs to remain awake during sleep or else __WFI() will disable the USB
__HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE();
__HAL_RCC_OTGPHYC_CLK_ENABLE();
__HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
#endif
__HAL_RCC_USB_OTG_HS_CLK_ENABLE();
#else // !MICROPY_HW_USB_HS_IN_FS
GPIO_InitTypeDef GPIO_InitStruct;
/* Configure USB HS GPIOs */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOH_CLK_ENABLE();
__HAL_RCC_GPIOI_CLK_ENABLE();
/* CLK */
GPIO_InitStruct.Pin = GPIO_PIN_5;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* D0 */
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* D1 D2 D3 D4 D5 D6 D7 */
GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_5 |\
GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* STP */
GPIO_InitStruct.Pin = GPIO_PIN_0;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* NXT */
GPIO_InitStruct.Pin = GPIO_PIN_4;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
/* DIR */
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
/* Enable USB HS Clocks */
__USB_OTG_HS_CLK_ENABLE();
__USB_OTG_HS_ULPI_CLK_ENABLE();
#endif // !MICROPY_HW_USB_HS_IN_FS
/* Set USBHS Interrupt to the lowest priority */
NVIC_SetPriority(OTG_HS_IRQn, IRQ_PRI_OTG_HS);
/* Enable USBHS Interrupt */
HAL_NVIC_EnableIRQ(OTG_HS_IRQn);
}
#endif // MICROPY_HW_USB_HS
}
/**
* @brief DeInitializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspDeInit(PCD_HandleTypeDef *hpcd)
{
if(hpcd->Instance == USB_OTG_FS)
{
/* Disable USB FS Clocks */
__USB_OTG_FS_CLK_DISABLE();
__SYSCFG_CLK_DISABLE();
}
#if MICROPY_HW_USB_HS
else if(hpcd->Instance == USB_OTG_HS)
{
/* Disable USB FS Clocks */
__USB_OTG_HS_CLK_DISABLE();
__SYSCFG_CLK_DISABLE();
}
#endif
}
/*******************************************************************************
LL Driver Callbacks (PCD -> USB Device Library)
*******************************************************************************/
/**
* @brief Setup stage callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_SetupStageCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_SetupStage(hpcd->pData, (uint8_t *)hpcd->Setup);
}
/**
* @brief Data Out stage callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_DataOutStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
USBD_LL_DataOutStage(hpcd->pData, epnum, hpcd->OUT_ep[epnum].xfer_buff);
}
/**
* @brief Data In stage callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_DataInStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
USBD_LL_DataInStage(hpcd->pData, epnum, hpcd->IN_ep[epnum].xfer_buff);
}
/**
* @brief SOF callback.
* @param hpcd: PCD handle
* @retval None
*/
/*
This is now handled by the USB CDC interface.
void HAL_PCD_SOFCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_SOF(hpcd->pData);
}
*/
/**
* @brief Reset callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ResetCallback(PCD_HandleTypeDef *hpcd)
{
USBD_SpeedTypeDef speed = USBD_SPEED_FULL;
/* Set USB Current Speed */
switch(hpcd->Init.speed)
{
#if defined(PCD_SPEED_HIGH)
case PCD_SPEED_HIGH:
speed = USBD_SPEED_HIGH;
break;
#endif
case PCD_SPEED_FULL:
speed = USBD_SPEED_FULL;
break;
default:
speed = USBD_SPEED_FULL;
break;
}
USBD_LL_SetSpeed(hpcd->pData, speed);
/* Reset Device */
USBD_LL_Reset(hpcd->pData);
}
/**
* @brief Suspend callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_SuspendCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_Suspend(hpcd->pData);
}
/**
* @brief Resume callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ResumeCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_Resume(hpcd->pData);
}
/**
* @brief ISOC Out Incomplete callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_ISOOUTIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
USBD_LL_IsoOUTIncomplete(hpcd->pData, epnum);
}
/**
* @brief ISOC In Incomplete callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_ISOINIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum)
{
USBD_LL_IsoINIncomplete(hpcd->pData, epnum);
}
/**
* @brief Connect callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ConnectCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_DevConnected(hpcd->pData);
}
/**
* @brief Disconnect callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_DisconnectCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_DevDisconnected(hpcd->pData);
}
/*******************************************************************************
LL Driver Interface (USB Device Library --> PCD)
*******************************************************************************/
/**
* @brief Initializes the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Init (USBD_HandleTypeDef *pdev, int high_speed)
{
#if MICROPY_HW_USB_FS
if (pdev->id == USB_PHY_FS_ID)
{
/*Set LL Driver parameters */
pcd_fs_handle.Instance = USB_OTG_FS;
pcd_fs_handle.Init.dev_endpoints = 4;
pcd_fs_handle.Init.use_dedicated_ep1 = 0;
pcd_fs_handle.Init.ep0_mps = 0x40;
pcd_fs_handle.Init.dma_enable = 0;
pcd_fs_handle.Init.low_power_enable = 0;
pcd_fs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
pcd_fs_handle.Init.Sof_enable = 1;
pcd_fs_handle.Init.speed = PCD_SPEED_FULL;
#if defined(STM32L4)
pcd_fs_handle.Init.lpm_enable = DISABLE;
pcd_fs_handle.Init.battery_charging_enable = DISABLE;
#endif
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
pcd_fs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
pcd_fs_handle.Init.vbus_sensing_enable = 1;
#endif
/* Link The driver to the stack */
pcd_fs_handle.pData = pdev;
pdev->pData = &pcd_fs_handle;
/*Initialize LL Driver */
HAL_PCD_Init(&pcd_fs_handle);
HAL_PCD_SetRxFiFo(&pcd_fs_handle, 0x80);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 0, 0x20);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 1, 0x40);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 2, 0x20);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 3, 0x40);
}
#endif
#if MICROPY_HW_USB_HS
if (pdev->id == USB_PHY_HS_ID)
{
#if MICROPY_HW_USB_HS_IN_FS
/*Set LL Driver parameters */
pcd_hs_handle.Instance = USB_OTG_HS;
pcd_hs_handle.Init.dev_endpoints = 4;
pcd_hs_handle.Init.use_dedicated_ep1 = 0;
pcd_hs_handle.Init.ep0_mps = 0x40;
pcd_hs_handle.Init.dma_enable = 0;
pcd_hs_handle.Init.low_power_enable = 0;
#if defined(STM32F723xx) || defined(STM32F733xx)
pcd_hs_handle.Init.phy_itface = USB_OTG_HS_EMBEDDED_PHY;
#else
pcd_hs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
#endif
pcd_hs_handle.Init.Sof_enable = 1;
if (high_speed) {
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH;
} else {
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH_IN_FULL;
}
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
pcd_hs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
pcd_hs_handle.Init.vbus_sensing_enable = 1;
#endif
pcd_hs_handle.Init.use_external_vbus = 0;
/* Link The driver to the stack */
pcd_hs_handle.pData = pdev;
pdev->pData = &pcd_hs_handle;
/*Initialize LL Driver */
HAL_PCD_Init(&pcd_hs_handle);
HAL_PCD_SetRxFiFo(&pcd_hs_handle, 0x200);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 0, 0x20);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 1, 0x100);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 2, 0x20);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 3, 0xc0);
#else // !MICROPY_HW_USB_HS_IN_FS
/*Set LL Driver parameters */
pcd_hs_handle.Instance = USB_OTG_HS;
pcd_hs_handle.Init.dev_endpoints = 6;
pcd_hs_handle.Init.use_dedicated_ep1 = 0;
pcd_hs_handle.Init.ep0_mps = 0x40;
/* Be aware that enabling USB-DMA mode will result in data being sent only by
multiple of 4 packet sizes. This is due to the fact that USB-DMA does
not allow sending data from non word-aligned addresses.
For this specific application, it is advised to not enable this option
unless required. */
pcd_hs_handle.Init.dma_enable = 0;
pcd_hs_handle.Init.low_power_enable = 0;
pcd_hs_handle.Init.phy_itface = PCD_PHY_ULPI;
pcd_hs_handle.Init.Sof_enable = 1;
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH;
pcd_hs_handle.Init.vbus_sensing_enable = 1;
/* Link The driver to the stack */
pcd_hs_handle.pData = pdev;
pdev->pData = &pcd_hs_handle;
/*Initialize LL Driver */
HAL_PCD_Init(&pcd_hs_handle);
HAL_PCD_SetRxFiFo(&pcd_hs_handle, 0x200);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 0, 0x80);
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 1, 0x174);
#endif // !MICROPY_HW_USB_HS_IN_FS
}
#endif // MICROPY_HW_USB_HS
return USBD_OK;
}
/**
* @brief De-Initializes the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_DeInit(USBD_HandleTypeDef *pdev)
{
HAL_PCD_DeInit(pdev->pData);
return USBD_OK;
}
/**
* @brief Starts the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Start(USBD_HandleTypeDef *pdev)
{
HAL_PCD_Start(pdev->pData);
return USBD_OK;
}
/**
* @brief Stops the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Stop(USBD_HandleTypeDef *pdev)
{
HAL_PCD_Stop(pdev->pData);
return USBD_OK;
}
/**
* @brief Opens an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param ep_type: Endpoint Type
* @param ep_mps: Endpoint Max Packet Size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_OpenEP(USBD_HandleTypeDef *pdev,
uint8_t ep_addr,
uint8_t ep_type,
uint16_t ep_mps)
{
HAL_PCD_EP_Open(pdev->pData, ep_addr, ep_mps, ep_type);
return USBD_OK;
}
/**
* @brief Closes an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_CloseEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
HAL_PCD_EP_Close(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Flushes an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_FlushEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
HAL_PCD_EP_Flush(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Sets a Stall condition on an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_StallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
HAL_PCD_EP_SetStall(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Clears a Stall condition on an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_ClearStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
HAL_PCD_EP_ClrStall(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Returns Stall condition.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval Stall (1: yes, 0: No)
*/
uint8_t USBD_LL_IsStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
PCD_HandleTypeDef *hpcd = pdev->pData;
if((ep_addr & 0x80) == 0x80)
{
return hpcd->IN_ep[ep_addr & 0x7F].is_stall;
}
else
{
return hpcd->OUT_ep[ep_addr & 0x7F].is_stall;
}
}
/**
* @brief Assigns an USB address to the device
* @param pdev: Device handle
* @param dev_addr: USB address
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_SetUSBAddress(USBD_HandleTypeDef *pdev, uint8_t dev_addr)
{
HAL_PCD_SetAddress(pdev->pData, dev_addr);
return USBD_OK;
}
/**
* @brief Transmits data over an endpoint
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param pbuf: Pointer to data to be sent
* @param size: Data size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Transmit(USBD_HandleTypeDef *pdev,
uint8_t ep_addr,
uint8_t *pbuf,
uint16_t size)
{
HAL_PCD_EP_Transmit(pdev->pData, ep_addr, pbuf, size);
return USBD_OK;
}
/**
* @brief Prepares an endpoint for reception
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param pbuf:pointer to data to be received
* @param size: data size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_PrepareReceive(USBD_HandleTypeDef *pdev,
uint8_t ep_addr,
uint8_t *pbuf,
uint16_t size)
{
HAL_PCD_EP_Receive(pdev->pData, ep_addr, pbuf, size);
return USBD_OK;
}
/**
* @brief Returns the last transfered packet size.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval Recived Data Size
*/
uint32_t USBD_LL_GetRxDataSize(USBD_HandleTypeDef *pdev, uint8_t ep_addr)
{
return HAL_PCD_EP_GetRxCount(pdev->pData, ep_addr);
}
/**
* @brief Delay routine for the USB Device Library
* @param Delay: Delay in ms
* @retval None
*/
void USBD_LL_Delay(uint32_t Delay)
{
HAL_Delay(Delay);
}
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/