circuitpython/ports/stm32/boards/HYDRABUS/mpconfigboard.h

75 lines
2.7 KiB
C

#define MICROPY_HW_BOARD_NAME "HydraBus1.0"
#define MICROPY_HW_MCU_NAME "STM32F4"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_ENABLE_SDCARD (1)
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
// UART config
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
#define MICROPY_HW_UART3_RTS (pin_D12)
#define MICROPY_HW_UART3_CTS (pin_D11)
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
#define MICROPY_HW_SPI3_NSS (pin_A4)
#define MICROPY_HW_SPI3_SCK (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)
// USRSW/UBTN (Needs Jumper UBTN) is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// The HydraBus has 1 LED (Needs jumper on ULED)
#define MICROPY_HW_LED1 (pin_A4) // green
#define MICROPY_HW_LED2 (pin_A4) // same as LED1
#define MICROPY_HW_LED3 (pin_A4) // same as LED1
#define MICROPY_HW_LED4 (pin_A4) // same as LED1
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// SD card detect switch (not used, always on)
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)