338635ccc6
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined by a board then the default values will be used (maximum heap from SRAM as defined by linker symbols). As part of this commit the SDRAM initialisation is moved to much earlier in main() to potentially make it available to other peripherals and avoid re-initialisation on soft-reboot. On boards with SDRAM enabled the heap has been set to use that.
142 lines
5.2 KiB
C
142 lines
5.2 KiB
C
#define MICROPY_HW_BOARD_NAME "F429I-DISCO"
|
|
#define MICROPY_HW_MCU_NAME "STM32F429"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
// HSE is 8MHz
|
|
#define MICROPY_HW_CLK_PLLM (8)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
#define MICROPY_HW_UART2_TX (pin_D8)
|
|
#define MICROPY_HW_UART2_RX (pin_D9)
|
|
|
|
// I2C busses
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
|
|
|
// SPI busses
|
|
//#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
//#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
//#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
//#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
#if defined(USE_USB_HS_IN_FS)
|
|
// The HS USB uses B14 & B15 for D- and D+
|
|
#else
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
#endif
|
|
//#define MICROPY_HW_SPI4_NSS (pin_E11)
|
|
//#define MICROPY_HW_SPI4_SCK (pin_E12)
|
|
//#define MICROPY_HW_SPI4_MISO (pin_E13)
|
|
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
|
|
#define MICROPY_HW_SPI5_NSS (pin_F6)
|
|
#define MICROPY_HW_SPI5_SCK (pin_F7)
|
|
#define MICROPY_HW_SPI5_MISO (pin_F8)
|
|
#define MICROPY_HW_SPI5_MOSI (pin_F9)
|
|
//#define MICROPY_HW_SPI6_NSS (pin_G8)
|
|
//#define MICROPY_HW_SPI6_SCK (pin_G13)
|
|
//#define MICROPY_HW_SPI6_MISO (pin_G12)
|
|
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
|
|
|
|
// CAN busses
|
|
#define MICROPY_HW_CAN1_TX (pin_B9)
|
|
#define MICROPY_HW_CAN1_RX (pin_B8)
|
|
#define MICROPY_HW_CAN2_TX (pin_B13)
|
|
#define MICROPY_HW_CAN2_RX (pin_B12)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_G14) // red
|
|
#define MICROPY_HW_LED2 (pin_G13) // green
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_HS (1)
|
|
#define MICROPY_HW_USB_HS_IN_FS (1)
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_B13)
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_B12)
|
|
|
|
// SDRAM
|
|
#define MICROPY_HW_SDRAM_SIZE (64 / 8 * 1024 * 1024) // 64 Mbit
|
|
#define MICROPY_HW_SDRAM_STARTUP_TEST (1)
|
|
#define MICROPY_HEAP_START sdram_start()
|
|
#define MICROPY_HEAP_END sdram_end()
|
|
|
|
// Timing configuration for 90 Mhz (11.90ns) of SD clock frequency (180Mhz/2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TMRD (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TXSR (7)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRAS (4)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRC (7)
|
|
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRP (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRCD (2)
|
|
#define MICROPY_HW_SDRAM_REFRESH_RATE (64) // ms
|
|
|
|
#define MICROPY_HW_SDRAM_BURST_LENGTH 2
|
|
#define MICROPY_HW_SDRAM_CAS_LATENCY 3
|
|
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM 8
|
|
#define MICROPY_HW_SDRAM_ROW_BITS_NUM 12
|
|
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH 16
|
|
#define MICROPY_HW_SDRAM_INTERN_BANKS_NUM 4
|
|
#define MICROPY_HW_SDRAM_CLOCK_PERIOD 2
|
|
#define MICROPY_HW_SDRAM_RPIPE_DELAY 1
|
|
#define MICROPY_HW_SDRAM_RBURST (0)
|
|
#define MICROPY_HW_SDRAM_WRITE_PROTECTION (0)
|
|
#define MICROPY_HW_SDRAM_AUTOREFRESH_NUM (4)
|
|
|
|
#define MICROPY_HW_FMC_SDCKE1 (pin_B5)
|
|
#define MICROPY_HW_FMC_SDNE1 (pin_B6)
|
|
#define MICROPY_HW_FMC_SDCLK (pin_G8)
|
|
#define MICROPY_HW_FMC_SDNCAS (pin_G15)
|
|
#define MICROPY_HW_FMC_SDNRAS (pin_F11)
|
|
#define MICROPY_HW_FMC_SDNWE (pin_C0)
|
|
#define MICROPY_HW_FMC_BA0 (pin_G4)
|
|
#define MICROPY_HW_FMC_BA1 (pin_G5)
|
|
#define MICROPY_HW_FMC_NBL0 (pin_E0)
|
|
#define MICROPY_HW_FMC_NBL1 (pin_E1)
|
|
#define MICROPY_HW_FMC_A0 (pin_F0)
|
|
#define MICROPY_HW_FMC_A1 (pin_F1)
|
|
#define MICROPY_HW_FMC_A2 (pin_F2)
|
|
#define MICROPY_HW_FMC_A3 (pin_F3)
|
|
#define MICROPY_HW_FMC_A4 (pin_F4)
|
|
#define MICROPY_HW_FMC_A5 (pin_F5)
|
|
#define MICROPY_HW_FMC_A6 (pin_F12)
|
|
#define MICROPY_HW_FMC_A7 (pin_F13)
|
|
#define MICROPY_HW_FMC_A8 (pin_F14)
|
|
#define MICROPY_HW_FMC_A9 (pin_F15)
|
|
#define MICROPY_HW_FMC_A10 (pin_G0)
|
|
#define MICROPY_HW_FMC_A11 (pin_G1)
|
|
#define MICROPY_HW_FMC_D0 (pin_D14)
|
|
#define MICROPY_HW_FMC_D1 (pin_D15)
|
|
#define MICROPY_HW_FMC_D2 (pin_D0)
|
|
#define MICROPY_HW_FMC_D3 (pin_D1)
|
|
#define MICROPY_HW_FMC_D4 (pin_E7)
|
|
#define MICROPY_HW_FMC_D5 (pin_E8)
|
|
#define MICROPY_HW_FMC_D6 (pin_E9)
|
|
#define MICROPY_HW_FMC_D7 (pin_E10)
|
|
#define MICROPY_HW_FMC_D8 (pin_E11)
|
|
#define MICROPY_HW_FMC_D9 (pin_E12)
|
|
#define MICROPY_HW_FMC_D10 (pin_E13)
|
|
#define MICROPY_HW_FMC_D11 (pin_E14)
|
|
#define MICROPY_HW_FMC_D12 (pin_E15)
|
|
#define MICROPY_HW_FMC_D13 (pin_D8)
|
|
#define MICROPY_HW_FMC_D14 (pin_D9)
|
|
#define MICROPY_HW_FMC_D15 (pin_D10)
|