djsundog/circuitpython
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
79e57473b2
circuitpython/ports/stm32/main.c
David Grayson c046b23ea2 shared/runtime/pyexec: Don't allow Ctrl+C to interrupt frozen boot code. 
Helps prevent the filesystem from getting formatted by mistake, among other
things.  For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).

Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state.  If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application.  The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it.  But defining
"long enough" is impossible for all the different boards and their possible
behaviour.  The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C.  That code then effectively
acts like normal C start-up code, which also cannot be interrupted.

Note: on the stm32 port this was never seen as an issue because all
start-up code is in C.  But now other ports start to put more things in
_boot.py and so this problem crops up.

Signed-off-by: David Grayson <davidegrayson@gmail.com>
2023-04-05 10:38:50 +10:00

671 lines
20 KiB
C
Raw Blame History

/*
* This file is part of the MicroPython project, http://micropython.org/
*
* The MIT License (MIT)
*
* Copyright (c) 2013-2020 Damien P. George
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
#include <stdio.h>
#include <string.h>
#include "py/runtime.h"
#include "py/stackctrl.h"
#include "py/gc.h"
#include "py/mperrno.h"
#include "py/mphal.h"
#include "shared/readline/readline.h"
#include "shared/runtime/pyexec.h"
#include "shared/runtime/softtimer.h"
#include "lib/oofatfs/ff.h"
#include "lib/littlefs/lfs1.h"
#include "lib/littlefs/lfs1_util.h"
#include "lib/littlefs/lfs2.h"
#include "lib/littlefs/lfs2_util.h"
#include "extmod/modnetwork.h"
#include "extmod/vfs.h"
#include "extmod/vfs_fat.h"
#include "extmod/vfs_lfs.h"
#if MICROPY_PY_LWIP
#include "lwip/init.h"
#include "lwip/apps/mdns.h"
#if MICROPY_PY_NETWORK_CYW43
#include "lib/cyw43-driver/src/cyw43.h"
#endif
#endif
#if MICROPY_PY_BLUETOOTH
#include "extmod/modbluetooth.h"
#endif
#include "boardctrl.h"
#include "mpbthciport.h"
#include "mpu.h"
#include "rfcore.h"
#include "systick.h"
#include "pendsv.h"
#include "powerctrl.h"
#include "pybthread.h"
#include "gccollect.h"
#include "factoryreset.h"
#include "modmachine.h"
#include "i2c.h"
#include "spi.h"
#include "uart.h"
#include "timer.h"
#include "led.h"
#include "pin.h"
#include "extint.h"
#include "usrsw.h"
#include "usb.h"
#include "rtc.h"
#include "storage.h"
#include "sdcard.h"
#include "sdram.h"
#include "rng.h"
#include "accel.h"
#include "servo.h"
#include "dac.h"
#include "can.h"
#if MICROPY_PY_THREAD
STATIC pyb_thread_t pyb_thread_main;
#endif
#if defined(MICROPY_HW_UART_REPL)
#ifndef MICROPY_HW_UART_REPL_RXBUF
#define MICROPY_HW_UART_REPL_RXBUF (260)
#endif
STATIC pyb_uart_obj_t pyb_uart_repl_obj;
STATIC uint8_t pyb_uart_repl_rxbuf[MICROPY_HW_UART_REPL_RXBUF];
#endif
void nlr_jump_fail(void *val) {
printf("FATAL: uncaught exception %p\n", val);
mp_obj_print_exception(&mp_plat_print, MP_OBJ_FROM_PTR(val));
MICROPY_BOARD_FATAL_ERROR("");
}
void abort(void) {
MICROPY_BOARD_FATAL_ERROR("abort");
}
#ifndef NDEBUG
void MP_WEAK __assert_func(const char *file, int line, const char *func, const char *expr) {
(void)func;
printf("Assertion '%s' failed, at file %s:%d\n", expr, file, line);
MICROPY_BOARD_FATAL_ERROR("");
}
#endif
STATIC mp_obj_t pyb_main(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
static const mp_arg_t allowed_args[] = {
{ MP_QSTR_opt, MP_ARG_INT, {.u_int = 0} }
};
if (mp_obj_is_str(pos_args[0])) {
MP_STATE_PORT(pyb_config_main) = pos_args[0];
// parse args
mp_arg_val_t args[MP_ARRAY_SIZE(allowed_args)];
mp_arg_parse_all(n_args - 1, pos_args + 1, kw_args, MP_ARRAY_SIZE(allowed_args), allowed_args, args);
#if MICROPY_ENABLE_COMPILER
MP_STATE_VM(mp_optimise_value) = args[0].u_int;
#endif
}
return mp_const_none;
}
MP_DEFINE_CONST_FUN_OBJ_KW(pyb_main_obj, 1, pyb_main);
#if MICROPY_HW_FLASH_MOUNT_AT_BOOT
// avoid inlining to avoid stack usage within main()
MP_NOINLINE STATIC bool init_flash_fs(uint reset_mode) {
if (reset_mode == BOARDCTRL_RESET_MODE_FACTORY_FILESYSTEM) {
// Asked by user to reset filesystem
factory_reset_create_filesystem();
}
// Default block device to entire flash storage
mp_obj_t bdev = MP_OBJ_FROM_PTR(&pyb_flash_obj);
int ret;
#if MICROPY_VFS_LFS1 || MICROPY_VFS_LFS2
// Try to detect the block device used for the main filesystem based on the
// contents of the superblock, which can be the first or second block.
mp_int_t len = -1;
uint8_t buf[64];
for (size_t block_num = 0; block_num <= 1; ++block_num) {
ret = storage_readblocks_ext(buf, block_num, 0, sizeof(buf));
#if MICROPY_VFS_LFS1
if (ret == 0 && memcmp(&buf[40], "littlefs", 8) == 0) {
// LFS1
lfs1_superblock_t *superblock = (void *)&buf[12];
uint32_t block_size = lfs1_fromle32(superblock->d.block_size);
uint32_t block_count = lfs1_fromle32(superblock->d.block_count);
len = block_count * block_size;
break;
}
#endif
#if MICROPY_VFS_LFS2
if (ret == 0 && memcmp(&buf[8], "littlefs", 8) == 0) {
// LFS2
lfs2_superblock_t *superblock = (void *)&buf[20];
uint32_t block_size = lfs2_fromle32(superblock->block_size);
uint32_t block_count = lfs2_fromle32(superblock->block_count);
len = block_count * block_size;
break;
}
#endif
}
if (len != -1) {
// Detected a littlefs filesystem so create correct block device for it
mp_obj_t args[] = { MP_OBJ_NEW_QSTR(MP_QSTR_len), MP_OBJ_NEW_SMALL_INT(len) };
bdev = MP_OBJ_TYPE_GET_SLOT(&pyb_flash_type, make_new)(&pyb_flash_type, 0, 1, args);
}
#endif
// Try to mount the flash on "/flash" and chdir to it for the boot-up directory.
mp_obj_t mount_point = MP_OBJ_NEW_QSTR(MP_QSTR__slash_flash);
ret = mp_vfs_mount_and_chdir_protected(bdev, mount_point);
if (ret == -MP_ENODEV && bdev == MP_OBJ_FROM_PTR(&pyb_flash_obj)
&& reset_mode != BOARDCTRL_RESET_MODE_FACTORY_FILESYSTEM) {
// No filesystem, bdev is still the default (so didn't detect a possibly corrupt littlefs),
// and didn't already create a filesystem, so try to create a fresh one now.
ret = factory_reset_create_filesystem();
if (ret == 0) {
ret = mp_vfs_mount_and_chdir_protected(bdev, mount_point);
}
}
if (ret != 0) {
mp_printf(&mp_plat_print, "MPY: can't mount flash\n");
return false;
}
return true;
}
#endif
#if MICROPY_HW_SDCARD_MOUNT_AT_BOOT
STATIC bool init_sdcard_fs(void) {
bool first_part = true;
for (int part_num = 1; part_num <= 5; ++part_num) {
// create vfs object
fs_user_mount_t *vfs_fat = m_new_obj_maybe(fs_user_mount_t);
mp_vfs_mount_t *vfs = m_new_obj_maybe(mp_vfs_mount_t);
if (vfs == NULL || vfs_fat == NULL) {
break;
}
vfs_fat->blockdev.flags = MP_BLOCKDEV_FLAG_FREE_OBJ;
if (part_num == 5) {
if (!first_part) {
break;
}
// partitions 1-4 couldn't be mounted, so try FATFS auto-detect mode
// which will work if there is no partition table, just a filesystem
sdcard_init_vfs(vfs_fat, 0);
} else {
sdcard_init_vfs(vfs_fat, part_num);
}
// try to mount the partition
FRESULT res = f_mount(&vfs_fat->fatfs);
if (res != FR_OK) {
// couldn't mount
m_del_obj(fs_user_mount_t, vfs_fat);
m_del_obj(mp_vfs_mount_t, vfs);
} else {
// mounted via FatFs, now mount the SD partition in the VFS
if (first_part) {
// the first available partition is traditionally called "sd" for simplicity
vfs->str = "/sd";
vfs->len = 3;
} else {
// subsequent partitions are numbered by their index in the partition table
if (part_num == 2) {
vfs->str = "/sd2";
} else if (part_num == 3) {
vfs->str = "/sd3";
} else {
vfs->str = "/sd4";
}
vfs->len = 4;
}
vfs->obj = MP_OBJ_FROM_PTR(vfs_fat);
vfs->next = NULL;
for (mp_vfs_mount_t **m = &MP_STATE_VM(vfs_mount_table);; m = &(*m)->next) {
if (*m == NULL) {
*m = vfs;
break;
}
}
#if MICROPY_HW_ENABLE_USB
if (pyb_usb_storage_medium == PYB_USB_STORAGE_MEDIUM_NONE) {
// if no USB MSC medium is selected then use the SD card
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_SDCARD;
}
#endif
#if MICROPY_HW_ENABLE_USB
// only use SD card as current directory if that's what the USB medium is
if (pyb_usb_storage_medium == PYB_USB_STORAGE_MEDIUM_SDCARD)
#endif
{
if (first_part) {
// use SD card as current directory
MP_STATE_PORT(vfs_cur) = vfs;
}
}
first_part = false;
}
}
if (first_part) {
mp_printf(&mp_plat_print, "MPY: can't mount SD card\n");
return false;
} else {
return true;
}
}
#endif
void stm32_main(uint32_t reset_mode) {
// Low-level MCU initialisation.
stm32_system_init();
#if !defined(STM32F0) && defined(MICROPY_HW_VTOR)
// Change IRQ vector table if configured differently
SCB->VTOR = MICROPY_HW_VTOR;
#endif
// Enable 8-byte stack alignment for IRQ handlers, in accord with EABI
SCB->CCR |= SCB_CCR_STKALIGN_Msk;
// Hook for a board to run code at start up, for example check if a
// bootloader should be entered instead of the main application.
MICROPY_BOARD_STARTUP();
// Enable caches and prefetch buffers
#if defined(STM32F4)
#if INSTRUCTION_CACHE_ENABLE
__HAL_FLASH_INSTRUCTION_CACHE_ENABLE();
#endif
#if DATA_CACHE_ENABLE
__HAL_FLASH_DATA_CACHE_ENABLE();
#endif
#if PREFETCH_ENABLE
__HAL_FLASH_PREFETCH_BUFFER_ENABLE();
#endif
#elif defined(STM32F7) || defined(STM32H7)
#if ART_ACCLERATOR_ENABLE
__HAL_FLASH_ART_ENABLE();
#endif
SCB_EnableICache();
SCB_EnableDCache();
#elif defined(STM32L4)
#if !INSTRUCTION_CACHE_ENABLE
__HAL_FLASH_INSTRUCTION_CACHE_DISABLE();
#endif
#if !DATA_CACHE_ENABLE
__HAL_FLASH_DATA_CACHE_DISABLE();
#endif
#if PREFETCH_ENABLE
__HAL_FLASH_PREFETCH_BUFFER_ENABLE();
#endif
#endif
mpu_init();
#if __CORTEX_M >= 0x03
// Set the priority grouping
NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);
#endif
// SysTick is needed by HAL_RCC_ClockConfig (called in SystemClock_Config)
HAL_InitTick(TICK_INT_PRIORITY);
// set the system clock to be HSE
SystemClock_Config();
#if defined(STM32F4) || defined(STM32F7)
#if defined(__HAL_RCC_DTCMRAMEN_CLK_ENABLE)
// The STM32F746 doesn't really have CCM memory, but it does have DTCM,
// which behaves more or less like normal SRAM.
__HAL_RCC_DTCMRAMEN_CLK_ENABLE();
#elif defined(CCMDATARAM_BASE)
// enable the CCM RAM
__HAL_RCC_CCMDATARAMEN_CLK_ENABLE();
#endif
#elif defined(STM32H7A3xx) || defined(STM32H7A3xxQ) || defined(STM32H7B3xx) || defined(STM32H7B3xxQ)
// Enable SRAM clock.
__HAL_RCC_SRDSRAM_CLK_ENABLE();
#elif defined(STM32H7)
// Enable D2 SRAM1/2/3 clocks.
__HAL_RCC_D2SRAM1_CLK_ENABLE();
__HAL_RCC_D2SRAM2_CLK_ENABLE();
#if defined(__HAL_RCC_D2SRAM3_CLK_ENABLE)
__HAL_RCC_D2SRAM3_CLK_ENABLE();
#endif
#endif
MICROPY_BOARD_EARLY_INIT();
// basic sub-system init
#if defined(STM32WB)
rfcore_init();
#endif
#if MICROPY_HW_SDRAM_SIZE
sdram_init();
bool sdram_valid = true;
UNUSED(sdram_valid);
#if MICROPY_HW_SDRAM_STARTUP_TEST
sdram_valid = sdram_test(false);
#endif
#endif
#if MICROPY_PY_THREAD
pyb_thread_init(&pyb_thread_main);
#endif
pendsv_init();
led_init();
#if MICROPY_HW_HAS_SWITCH
switch_init0();
#endif
machine_init();
#if MICROPY_HW_ENABLE_RTC
rtc_init_start(false);
#endif
uart_init0();
spi_init0();
#if MICROPY_PY_PYB_LEGACY && MICROPY_HW_ENABLE_HW_I2C
i2c_init0();
#endif
#if MICROPY_HW_ENABLE_SDCARD || MICROPY_HW_ENABLE_MMCARD
sdcard_init();
#endif
#if MICROPY_HW_ENABLE_STORAGE
storage_init();
#endif
#if MICROPY_PY_LWIP
// lwIP doesn't allow to reinitialise itself by subsequent calls to this function
// because the system timeout list (next_timeout) is only ever reset by BSS clearing.
// So for now we only init the lwIP stack once on power-up.
lwip_init();
#if LWIP_MDNS_RESPONDER
mdns_resp_init();
#endif
systick_enable_dispatch(SYSTICK_DISPATCH_LWIP, mod_network_lwip_poll_wrapper);
#endif
#if MICROPY_PY_BLUETOOTH
mp_bluetooth_hci_init();
#endif
#if MICROPY_PY_NETWORK_CYW43
{
cyw43_init(&cyw43_state);
uint8_t buf[8];
memcpy(&buf[0], "PYBD", 4);
mp_hal_get_mac_ascii(MP_HAL_MAC_WLAN0, 8, 4, (char *)&buf[4]);
cyw43_wifi_ap_set_ssid(&cyw43_state, 8, buf);
cyw43_wifi_ap_set_password(&cyw43_state, 8, (const uint8_t *)"pybd0123");
}
#endif
#if defined(MICROPY_HW_UART_REPL)
// Set up a UART REPL using a statically allocated object
pyb_uart_repl_obj.base.type = &pyb_uart_type;
pyb_uart_repl_obj.uart_id = MICROPY_HW_UART_REPL;
pyb_uart_repl_obj.is_static = true;
pyb_uart_repl_obj.timeout = 0;
pyb_uart_repl_obj.timeout_char = 2;
uart_init(&pyb_uart_repl_obj, MICROPY_HW_UART_REPL_BAUD, UART_WORDLENGTH_8B, UART_PARITY_NONE, UART_STOPBITS_1, 0);
uart_set_rxbuf(&pyb_uart_repl_obj, sizeof(pyb_uart_repl_rxbuf), pyb_uart_repl_rxbuf);
uart_attach_to_repl(&pyb_uart_repl_obj, true);
MP_STATE_PORT(pyb_uart_obj_all)[MICROPY_HW_UART_REPL - 1] = &pyb_uart_repl_obj;
#endif
boardctrl_state_t state;
state.reset_mode = reset_mode;
state.log_soft_reset = false;
MICROPY_BOARD_BEFORE_SOFT_RESET_LOOP(&state);
soft_reset:
MICROPY_BOARD_TOP_SOFT_RESET_LOOP(&state);
// Python threading init
#if MICROPY_PY_THREAD
mp_thread_init();
#endif
// Stack limit should be less than real stack size, so we have a chance
// to recover from limit hit. (Limit is measured in bytes.)
// Note: stack control relies on main thread being initialised above
mp_stack_set_top(&_estack);
mp_stack_set_limit((char *)&_estack - (char *)&_sstack - 1024);
// GC init
gc_init(MICROPY_HEAP_START, MICROPY_HEAP_END);
#if MICROPY_ENABLE_PYSTACK
static mp_obj_t pystack[384];
mp_pystack_init(pystack, &pystack[384]);
#endif
// MicroPython init
mp_init();
// Initialise low-level sub-systems. Here we need to very basic things like
// zeroing out memory and resetting any of the sub-systems. Following this
// we can run Python scripts (eg boot.py), but anything that is configurable
// by boot.py must be set after boot.py is run.
#if defined(MICROPY_HW_UART_REPL)
MP_STATE_PORT(pyb_stdio_uart) = &pyb_uart_repl_obj;
#else
MP_STATE_PORT(pyb_stdio_uart) = NULL;
#endif
readline_init0();
pin_init0();
extint_init0();
timer_init0();
#if MICROPY_HW_ENABLE_CAN
can_init0();
#endif
#if MICROPY_HW_ENABLE_USB
pyb_usb_init0();
#endif
#if MICROPY_HW_ENABLE_I2S
machine_i2s_init0();
#endif
// Initialise the local flash filesystem.
// Create it if needed, mount in on /flash, and set it as current dir.
bool mounted_flash = false;
#if MICROPY_HW_FLASH_MOUNT_AT_BOOT
mounted_flash = init_flash_fs(state.reset_mode);
#endif
bool mounted_sdcard = false;
#if MICROPY_HW_SDCARD_MOUNT_AT_BOOT
// if an SD card is present then mount it on /sd/
if (sdcard_is_present()) {
// if there is a file in the flash called "SKIPSD", then we don't mount the SD card
if (!mounted_flash || mp_vfs_import_stat("SKIPSD") == MP_IMPORT_STAT_NO_EXIST) {
mounted_sdcard = init_sdcard_fs();
}
}
#endif
#if MICROPY_HW_ENABLE_USB
// if the SD card isn't used as the USB MSC medium then use the internal flash
if (pyb_usb_storage_medium == PYB_USB_STORAGE_MEDIUM_NONE) {
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_FLASH;
}
#endif
// set sys.path based on mounted filesystems (/sd is first so it can override /flash)
if (mounted_sdcard) {
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_sd));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_sd_slash_lib));
}
if (mounted_flash) {
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_flash));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_flash_slash_lib));
}
// reset config variables; they should be set by boot.py
MP_STATE_PORT(pyb_config_main) = MP_OBJ_NULL;
// Run optional frozen boot code.
#ifdef MICROPY_BOARD_FROZEN_BOOT_FILE
pyexec_frozen_module(MICROPY_BOARD_FROZEN_BOOT_FILE, false);
#endif
// Run boot.py (or whatever else a board configures at this stage).
if (MICROPY_BOARD_RUN_BOOT_PY(&state) == BOARDCTRL_GOTO_SOFT_RESET_EXIT) {
goto soft_reset_exit;
}
// Now we initialise sub-systems that need configuration from boot.py,
// or whose initialisation can be safely deferred until after running
// boot.py.
#if MICROPY_HW_ENABLE_USB
// init USB device to default setting if it was not already configured
if (!(pyb_usb_flags & PYB_USB_FLAG_USB_MODE_CALLED)) {
#if MICROPY_HW_USB_MSC
const uint16_t pid = MICROPY_HW_USB_PID_CDC_MSC;
const uint8_t mode = USBD_MODE_CDC_MSC;
#else
const uint16_t pid = MICROPY_HW_USB_PID_CDC;
const uint8_t mode = USBD_MODE_CDC;
#endif
pyb_usb_dev_init(pyb_usb_dev_detect(), MICROPY_HW_USB_VID, pid, mode, 0, NULL, NULL);
}
#endif
#if MICROPY_HW_HAS_MMA7660
// MMA accel: init and reset
accel_init();
#endif
#if MICROPY_HW_ENABLE_SERVO
servo_init();
#endif
#if MICROPY_PY_NETWORK
mod_network_init();
#endif
// At this point everything is fully configured and initialised.
// Run main.py (or whatever else a board configures at this stage).
if (MICROPY_BOARD_RUN_MAIN_PY(&state) == BOARDCTRL_GOTO_SOFT_RESET_EXIT) {
goto soft_reset_exit;
}
#if MICROPY_ENABLE_COMPILER
// Main script is finished, so now go into REPL mode.
// The REPL mode can change, or it can request a soft reset.
for (;;) {
if (pyexec_mode_kind == PYEXEC_MODE_RAW_REPL) {
if (pyexec_raw_repl() != 0) {
break;
}
} else {
if (pyexec_friendly_repl() != 0) {
break;
}
}
}
#endif
soft_reset_exit:
// soft reset
MICROPY_BOARD_START_SOFT_RESET(&state);
#if MICROPY_HW_ENABLE_STORAGE
if (state.log_soft_reset) {
mp_printf(&mp_plat_print, "MPY: sync filesystems\n");
}
storage_flush();
#endif
if (state.log_soft_reset) {
mp_printf(&mp_plat_print, "MPY: soft reboot\n");
}
#if MICROPY_PY_BLUETOOTH
mp_bluetooth_deinit();
#endif
#if MICROPY_PY_NETWORK
mod_network_deinit();
#endif
soft_timer_deinit();
timer_deinit();
uart_deinit_all();
#if MICROPY_HW_ENABLE_CAN
can_deinit_all();
#endif
#if MICROPY_HW_ENABLE_DAC
dac_deinit_all();
#endif
machine_deinit();
#if MICROPY_PY_THREAD
pyb_thread_deinit();
#endif
MICROPY_BOARD_END_SOFT_RESET(&state);
gc_sweep_all();
mp_deinit();
goto soft_reset;
}
MP_REGISTER_ROOT_POINTER(mp_obj_t pyb_config_main);
Reference in New Issue View Git Blame Copy Permalink