6ef8639971
This creates a common safe mode mechanic that ports can share. As a result, the nRF52 now has safe mode support as well. The common safe mode adds a 700ms delay at startup where a reset during that window will cause a reset into safe mode. This window is designated by a yellow status pixel and flashing the single led three times. A couple NeoPixel fixes are included for the nRF52 as well. Fixes #1034. Fixes #990. Fixes #615.
68 lines
2.8 KiB
C
68 lines
2.8 KiB
C
/*
|
|
* This file is part of the MicroPython project, http://micropython.org/
|
|
*
|
|
* The MIT License (MIT)
|
|
*
|
|
* Copyright (c) 2016 Glenn Ruben Bakke
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*/
|
|
|
|
#include "nrfx/hal/nrf_gpio.h"
|
|
|
|
#define MICROPY_HW_BOARD_NAME "PCA10056 nRF52840-DK"
|
|
#define MICROPY_HW_MCU_NAME "nRF52840"
|
|
#define MICROPY_PY_SYS_PLATFORM "nRF52840-DK"
|
|
|
|
#define PORT_HEAP_SIZE (128 * 1024)
|
|
#define CIRCUITPY_AUTORELOAD_DELAY_MS 500
|
|
|
|
#define MICROPY_HW_LED_STATUS (&pin_P0_13)
|
|
|
|
#define DEFAULT_I2C_BUS_SCL (&pin_P0_27)
|
|
#define DEFAULT_I2C_BUS_SDA (&pin_P0_26)
|
|
|
|
#define DEFAULT_SPI_BUS_SCK (&pin_P1_15)
|
|
#define DEFAULT_SPI_BUS_MOSI (&pin_P1_13)
|
|
#define DEFAULT_SPI_BUS_MISO (&pin_P1_14)
|
|
|
|
#define DEFAULT_UART_BUS_RX (&pin_P1_01)
|
|
#define DEFAULT_UART_BUS_TX (&pin_P1_02)
|
|
|
|
// Flash operation mode is determined by MICROPY_QSPI_DATAn pin configuration.
|
|
// A pin config is valid if it is defined and its value is not 0xFF.
|
|
// Quad mode: If all DATA0 --> DATA3 are valid
|
|
// Dual mode: If DATA0 and DATA1 are valid while either DATA2 and/or DATA3 are invalid
|
|
// Single mode: If only DATA0 is valid
|
|
#ifdef QSPI_FLASH_FILESYSTEM
|
|
#define MICROPY_QSPI_DATA0 NRF_GPIO_PIN_MAP(0, 20)
|
|
#define MICROPY_QSPI_DATA1 NRF_GPIO_PIN_MAP(0, 21)
|
|
#define MICROPY_QSPI_DATA2 NRF_GPIO_PIN_MAP(0, 22)
|
|
#define MICROPY_QSPI_DATA3 NRF_GPIO_PIN_MAP(0, 23)
|
|
#define MICROPY_QSPI_SCK NRF_GPIO_PIN_MAP(0, 19)
|
|
#define MICROPY_QSPI_CS NRF_GPIO_PIN_MAP(0, 17)
|
|
#endif
|
|
|
|
#ifdef SPI_FLASH_FILESYSTEM
|
|
#define SPI_FLASH_MOSI_PIN &pin_P0_20
|
|
#define SPI_FLASH_MISO_PIN &pin_P0_21
|
|
#define SPI_FLASH_SCK_PIN &pin_P0_19
|
|
#define SPI_FLASH_CS_PIN &pin_P0_17
|
|
#endif
|