758 lines
26 KiB
ReStructuredText
758 lines
26 KiB
ReStructuredText
.. _esp32_quickref:
|
||
|
||
Quick reference for the ESP32
|
||
=============================
|
||
|
||
.. image:: img/esp32.jpg
|
||
:alt: ESP32 board
|
||
:width: 640px
|
||
|
||
The Espressif ESP32 Development Board (image attribution: Adafruit).
|
||
|
||
Below is a quick reference for ESP32-based boards. If it is your first time
|
||
working with this board it may be useful to get an overview of the microcontroller:
|
||
|
||
.. toctree::
|
||
:maxdepth: 1
|
||
|
||
general.rst
|
||
tutorial/index.rst
|
||
|
||
Installing MicroPython
|
||
----------------------
|
||
|
||
See the corresponding section of tutorial: :ref:`esp32_intro`. It also includes
|
||
a troubleshooting subsection.
|
||
|
||
General board control
|
||
---------------------
|
||
|
||
The MicroPython REPL is on UART0 (GPIO1=TX, GPIO3=RX) at baudrate 115200.
|
||
Tab-completion is useful to find out what methods an object has.
|
||
Paste mode (ctrl-E) is useful to paste a large slab of Python code into
|
||
the REPL.
|
||
|
||
The :mod:`machine` module::
|
||
|
||
import machine
|
||
|
||
machine.freq() # get the current frequency of the CPU
|
||
machine.freq(240000000) # set the CPU frequency to 240 MHz
|
||
|
||
The :mod:`esp` module::
|
||
|
||
import esp
|
||
|
||
esp.osdebug(None) # turn off vendor O/S debugging messages
|
||
esp.osdebug(0) # redirect vendor O/S debugging messages to UART(0)
|
||
|
||
# low level methods to interact with flash storage
|
||
esp.flash_size()
|
||
esp.flash_user_start()
|
||
esp.flash_erase(sector_no)
|
||
esp.flash_write(byte_offset, buffer)
|
||
esp.flash_read(byte_offset, buffer)
|
||
|
||
The :mod:`esp32` module::
|
||
|
||
import esp32
|
||
|
||
esp32.hall_sensor() # read the internal hall sensor
|
||
esp32.raw_temperature() # read the internal temperature of the MCU, in Fahrenheit
|
||
esp32.ULP() # access to the Ultra-Low-Power Co-processor
|
||
|
||
Note that the temperature sensor in the ESP32 will typically read higher than
|
||
ambient due to the IC getting warm while it runs. This effect can be minimised
|
||
by reading the temperature sensor immediately after waking up from sleep.
|
||
|
||
Networking
|
||
----------
|
||
|
||
The :mod:`network` module::
|
||
|
||
import network
|
||
|
||
wlan = network.WLAN(network.STA_IF) # create station interface
|
||
wlan.active(True) # activate the interface
|
||
wlan.scan() # scan for access points
|
||
wlan.isconnected() # check if the station is connected to an AP
|
||
wlan.connect('ssid', 'key') # connect to an AP
|
||
wlan.config('mac') # get the interface's MAC address
|
||
wlan.ifconfig() # get the interface's IP/netmask/gw/DNS addresses
|
||
|
||
ap = network.WLAN(network.AP_IF) # create access-point interface
|
||
ap.config(ssid='ESP-AP') # set the SSID of the access point
|
||
ap.config(max_clients=10) # set how many clients can connect to the network
|
||
ap.active(True) # activate the interface
|
||
|
||
A useful function for connecting to your local WiFi network is::
|
||
|
||
def do_connect():
|
||
import network
|
||
wlan = network.WLAN(network.STA_IF)
|
||
wlan.active(True)
|
||
if not wlan.isconnected():
|
||
print('connecting to network...')
|
||
wlan.connect('ssid', 'key')
|
||
while not wlan.isconnected():
|
||
pass
|
||
print('network config:', wlan.ifconfig())
|
||
|
||
Once the network is established the :mod:`socket <socket>` module can be used
|
||
to create and use TCP/UDP sockets as usual, and the ``urequests`` module for
|
||
convenient HTTP requests.
|
||
|
||
After a call to ``wlan.connect()``, the device will by default retry to connect
|
||
**forever**, even when the authentication failed or no AP is in range.
|
||
``wlan.status()`` will return ``network.STAT_CONNECTING`` in this state until a
|
||
connection succeeds or the interface gets disabled. This can be changed by
|
||
calling ``wlan.config(reconnects=n)``, where n are the number of desired reconnect
|
||
attempts (0 means it won't retry, -1 will restore the default behaviour of trying
|
||
to reconnect forever).
|
||
|
||
Delay and timing
|
||
----------------
|
||
|
||
Use the :mod:`time <time>` module::
|
||
|
||
import time
|
||
|
||
time.sleep(1) # sleep for 1 second
|
||
time.sleep_ms(500) # sleep for 500 milliseconds
|
||
time.sleep_us(10) # sleep for 10 microseconds
|
||
start = time.ticks_ms() # get millisecond counter
|
||
delta = time.ticks_diff(time.ticks_ms(), start) # compute time difference
|
||
|
||
Timers
|
||
------
|
||
|
||
The ESP32 port has four hardware timers. Use the :ref:`machine.Timer <machine.Timer>` class
|
||
with a timer ID from 0 to 3 (inclusive)::
|
||
|
||
from machine import Timer
|
||
|
||
tim0 = Timer(0)
|
||
tim0.init(period=5000, mode=Timer.ONE_SHOT, callback=lambda t:print(0))
|
||
|
||
tim1 = Timer(1)
|
||
tim1.init(period=2000, mode=Timer.PERIODIC, callback=lambda t:print(1))
|
||
|
||
The period is in milliseconds.
|
||
|
||
Virtual timers are not currently supported on this port.
|
||
|
||
.. _Pins_and_GPIO:
|
||
|
||
Pins and GPIO
|
||
-------------
|
||
|
||
Use the :ref:`machine.Pin <machine.Pin>` class::
|
||
|
||
from machine import Pin
|
||
|
||
p0 = Pin(0, Pin.OUT) # create output pin on GPIO0
|
||
p0.on() # set pin to "on" (high) level
|
||
p0.off() # set pin to "off" (low) level
|
||
p0.value(1) # set pin to on/high
|
||
|
||
p2 = Pin(2, Pin.IN) # create input pin on GPIO2
|
||
print(p2.value()) # get value, 0 or 1
|
||
|
||
p4 = Pin(4, Pin.IN, Pin.PULL_UP) # enable internal pull-up resistor
|
||
p5 = Pin(5, Pin.OUT, value=1) # set pin high on creation
|
||
p6 = Pin(6, Pin.OUT, drive=Pin.DRIVE_3) # set maximum drive strength
|
||
|
||
Available Pins are from the following ranges (inclusive): 0-19, 21-23, 25-27, 32-39.
|
||
These correspond to the actual GPIO pin numbers of ESP32 chip. Note that many
|
||
end-user boards use their own adhoc pin numbering (marked e.g. D0, D1, ...).
|
||
For mapping between board logical pins and physical chip pins consult your board
|
||
documentation.
|
||
|
||
Four drive strengths are supported, using the ``drive`` keyword argument to the
|
||
``Pin()`` constructor or ``Pin.init()`` method, with different corresponding
|
||
safe maximum source/sink currents and approximate internal driver resistances:
|
||
|
||
- ``Pin.DRIVE_0``: 5mA / 130 ohm
|
||
- ``Pin.DRIVE_1``: 10mA / 60 ohm
|
||
- ``Pin.DRIVE_2``: 20mA / 30 ohm (default strength if not configured)
|
||
- ``Pin.DRIVE_3``: 40mA / 15 ohm
|
||
|
||
The ``hold=`` keyword argument to ``Pin()`` and ``Pin.init()`` will enable the
|
||
ESP32 "pad hold" feature. When set to ``True``, the pin configuration
|
||
(direction, pull resistors and output value) will be held and any further
|
||
changes (including changing the output level) will not be applied. Setting
|
||
``hold=False`` will immediately apply any outstanding pin configuration changes
|
||
and release the pin. Using ``hold=True`` while a pin is already held will apply
|
||
any configuration changes and then immediately reapply the hold.
|
||
|
||
Notes:
|
||
|
||
* Pins 1 and 3 are REPL UART TX and RX respectively
|
||
|
||
* Pins 6, 7, 8, 11, 16, and 17 are used for connecting the embedded flash,
|
||
and are not recommended for other uses
|
||
|
||
* Pins 34-39 are input only, and also do not have internal pull-up resistors
|
||
|
||
* See :ref:`Deep_sleep_Mode` for a discussion of pin behaviour during sleep
|
||
|
||
There's a higher-level abstraction :ref:`machine.Signal <machine.Signal>`
|
||
which can be used to invert a pin. Useful for illuminating active-low LEDs
|
||
using ``on()`` or ``value(1)``.
|
||
|
||
UART (serial bus)
|
||
-----------------
|
||
|
||
See :ref:`machine.UART <machine.UART>`. ::
|
||
|
||
from machine import UART
|
||
|
||
uart1 = UART(1, baudrate=9600, tx=33, rx=32)
|
||
uart1.write('hello') # write 5 bytes
|
||
uart1.read(5) # read up to 5 bytes
|
||
|
||
The ESP32 has three hardware UARTs: UART0, UART1 and UART2.
|
||
They each have default GPIO assigned to them, however depending on your
|
||
ESP32 variant and board, these pins may conflict with embedded flash,
|
||
onboard PSRAM or peripherals.
|
||
|
||
Any GPIO can be used for hardware UARTs using the GPIO matrix, except for
|
||
input-only pins 34-39 that can be used as ``rx``. To avoid conflicts simply
|
||
provide ``tx`` and ``rx`` pins when constructing. The default pins listed
|
||
below.
|
||
|
||
===== ===== ===== =====
|
||
\ UART0 UART1 UART2
|
||
===== ===== ===== =====
|
||
tx 1 10 17
|
||
rx 3 9 16
|
||
===== ===== ===== =====
|
||
|
||
PWM (pulse width modulation)
|
||
----------------------------
|
||
|
||
PWM can be enabled on all output-enabled pins. The base frequency can
|
||
range from 1Hz to 40MHz but there is a tradeoff; as the base frequency
|
||
*increases* the duty resolution *decreases*. See
|
||
`LED Control <https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/peripherals/ledc.html>`_
|
||
for more details.
|
||
|
||
Use the :ref:`machine.PWM <machine.PWM>` class::
|
||
|
||
from machine import Pin, PWM
|
||
|
||
pwm0 = PWM(Pin(0)) # create PWM object from a pin
|
||
freq = pwm0.freq() # get current frequency (default 5kHz)
|
||
pwm0.freq(1000) # set PWM frequency from 1Hz to 40MHz
|
||
|
||
duty = pwm0.duty() # get current duty cycle, range 0-1023 (default 512, 50%)
|
||
pwm0.duty(256) # set duty cycle from 0 to 1023 as a ratio duty/1023, (now 25%)
|
||
|
||
duty_u16 = pwm0.duty_u16() # get current duty cycle, range 0-65535
|
||
pwm0.duty_u16(2**16*3//4) # set duty cycle from 0 to 65535 as a ratio duty_u16/65535, (now 75%)
|
||
|
||
duty_ns = pwm0.duty_ns() # get current pulse width in ns
|
||
pwm0.duty_ns(250_000) # set pulse width in nanoseconds from 0 to 1_000_000_000/freq, (now 25%)
|
||
|
||
pwm0.deinit() # turn off PWM on the pin
|
||
|
||
pwm2 = PWM(Pin(2), freq=20000, duty=512) # create and configure in one go
|
||
print(pwm2) # view PWM settings
|
||
|
||
ESP chips have different hardware peripherals:
|
||
|
||
===================================================== ======== ======== ========
|
||
Hardware specification ESP32 ESP32-S2 ESP32-C3
|
||
----------------------------------------------------- -------- -------- --------
|
||
Number of groups (speed modes) 2 1 1
|
||
Number of timers per group 4 4 4
|
||
Number of channels per group 8 8 6
|
||
----------------------------------------------------- -------- -------- --------
|
||
Different PWM frequencies (groups * timers) 8 4 4
|
||
Total PWM channels (Pins, duties) (groups * channels) 16 8 6
|
||
===================================================== ======== ======== ========
|
||
|
||
A maximum number of PWM channels (Pins) are available on the ESP32 - 16 channels,
|
||
but only 8 different PWM frequencies are available, the remaining 8 channels must
|
||
have the same frequency. On the other hand, 16 independent PWM duty cycles are
|
||
possible at the same frequency.
|
||
|
||
See more examples in the :ref:`esp32_pwm` tutorial.
|
||
|
||
ADC (analog to digital conversion)
|
||
----------------------------------
|
||
|
||
On the ESP32, ADC functionality is available on pins 32-39 (ADC block 1) and
|
||
pins 0, 2, 4, 12-15 and 25-27 (ADC block 2).
|
||
|
||
Use the :ref:`machine.ADC <machine.ADC>` class::
|
||
|
||
from machine import ADC
|
||
|
||
adc = ADC(pin) # create an ADC object acting on a pin
|
||
val = adc.read_u16() # read a raw analog value in the range 0-65535
|
||
val = adc.read_uv() # read an analog value in microvolts
|
||
|
||
ADC block 2 is also used by WiFi and so attempting to read analog values from
|
||
block 2 pins when WiFi is active will raise an exception.
|
||
|
||
The internal ADC reference voltage is typically 1.1V, but varies slightly from
|
||
package to package. The ADC is less linear close to the reference voltage
|
||
(particularly at higher attenuations) and has a minimum measurement voltage
|
||
around 100mV, voltages at or below this will read as 0. To read voltages
|
||
accurately, it is recommended to use the ``read_uv()`` method (see below).
|
||
|
||
ESP32-specific ADC class method reference:
|
||
|
||
.. class:: ADC(pin, *, atten)
|
||
|
||
Return the ADC object for the specified pin. ESP32 does not support
|
||
different timings for ADC sampling and so the ``sample_ns`` keyword argument
|
||
is not supported.
|
||
|
||
To read voltages above the reference voltage, apply input attenuation with
|
||
the ``atten`` keyword argument. Valid values (and approximate linear
|
||
measurement ranges) are:
|
||
|
||
- ``ADC.ATTN_0DB``: No attenuation (100mV - 950mV)
|
||
- ``ADC.ATTN_2_5DB``: 2.5dB attenuation (100mV - 1250mV)
|
||
- ``ADC.ATTN_6DB``: 6dB attenuation (150mV - 1750mV)
|
||
- ``ADC.ATTN_11DB``: 11dB attenuation (150mV - 2450mV)
|
||
|
||
.. Warning::
|
||
Note that the absolute maximum voltage rating for input pins is 3.6V. Going
|
||
near to this boundary risks damage to the IC!
|
||
|
||
.. method:: ADC.read_uv()
|
||
|
||
This method uses the known characteristics of the ADC and per-package eFuse
|
||
values - set during manufacture - to return a calibrated input voltage
|
||
(before attenuation) in microvolts. The returned value has only millivolt
|
||
resolution (i.e., will always be a multiple of 1000 microvolts).
|
||
|
||
The calibration is only valid across the linear range of the ADC. In
|
||
particular, an input tied to ground will read as a value above 0 microvolts.
|
||
Within the linear range, however, more accurate and consistent results will
|
||
be obtained than using `read_u16()` and scaling the result with a constant.
|
||
|
||
The ESP32 port also supports the :ref:`machine.ADC <machine.ADCBlock>` API:
|
||
|
||
.. class:: ADCBlock(id, *, bits)
|
||
|
||
Return the ADC block object with the given ``id`` (1 or 2) and initialize
|
||
it to the specified resolution (9 to 12-bits depending on the ESP32 series)
|
||
or the highest supported resolution if not specified.
|
||
|
||
.. method:: ADCBlock.connect(pin)
|
||
ADCBlock.connect(channel)
|
||
ADCBlock.connect(channel, pin)
|
||
|
||
Return the ``ADC`` object for the specified ADC pin or channel number.
|
||
Arbitrary connection of ADC channels to GPIO is not supported and so
|
||
specifying a pin that is not connected to this block, or specifying a
|
||
mismatched channel and pin, will raise an exception.
|
||
|
||
Legacy methods:
|
||
|
||
.. method:: ADC.read()
|
||
|
||
This method returns the raw ADC value ranged according to the resolution of
|
||
the block, e.g., 0-4095 for 12-bit resolution.
|
||
|
||
.. method:: ADC.atten(atten)
|
||
|
||
Equivalent to ``ADC.init(atten=atten)``.
|
||
|
||
.. method:: ADC.width(bits)
|
||
|
||
Equivalent to ``ADC.block().init(bits=bits)``.
|
||
|
||
For compatibility, the ``ADC`` object also provides constants matching the
|
||
supported ADC resolutions:
|
||
|
||
- ``ADC.WIDTH_9BIT`` = 9
|
||
- ``ADC.WIDTH_10BIT`` = 10
|
||
- ``ADC.WIDTH_11BIT`` = 11
|
||
- ``ADC.WIDTH_12BIT`` = 12
|
||
|
||
|
||
Software SPI bus
|
||
----------------
|
||
|
||
Software SPI (using bit-banging) works on all pins, and is accessed via the
|
||
:ref:`machine.SoftSPI <machine.SoftSPI>` class::
|
||
|
||
from machine import Pin, SoftSPI
|
||
|
||
# construct a SoftSPI bus on the given pins
|
||
# polarity is the idle state of SCK
|
||
# phase=0 means sample on the first edge of SCK, phase=1 means the second
|
||
spi = SoftSPI(baudrate=100000, polarity=1, phase=0, sck=Pin(0), mosi=Pin(2), miso=Pin(4))
|
||
|
||
spi.init(baudrate=200000) # set the baudrate
|
||
|
||
spi.read(10) # read 10 bytes on MISO
|
||
spi.read(10, 0xff) # read 10 bytes while outputting 0xff on MOSI
|
||
|
||
buf = bytearray(50) # create a buffer
|
||
spi.readinto(buf) # read into the given buffer (reads 50 bytes in this case)
|
||
spi.readinto(buf, 0xff) # read into the given buffer and output 0xff on MOSI
|
||
|
||
spi.write(b'12345') # write 5 bytes on MOSI
|
||
|
||
buf = bytearray(4) # create a buffer
|
||
spi.write_readinto(b'1234', buf) # write to MOSI and read from MISO into the buffer
|
||
spi.write_readinto(buf, buf) # write buf to MOSI and read MISO back into buf
|
||
|
||
.. Warning::
|
||
Currently *all* of ``sck``, ``mosi`` and ``miso`` *must* be specified when
|
||
initialising Software SPI.
|
||
|
||
Hardware SPI bus
|
||
----------------
|
||
|
||
There are two hardware SPI channels that allow faster transmission
|
||
rates (up to 80Mhz). These may be used on any IO pins that support the
|
||
required direction and are otherwise unused (see :ref:`Pins_and_GPIO`)
|
||
but if they are not configured to their default pins then they need to
|
||
pass through an extra layer of GPIO multiplexing, which can impact
|
||
their reliability at high speeds. Hardware SPI channels are limited
|
||
to 40MHz when used on pins other than the default ones listed below.
|
||
|
||
===== =========== ============
|
||
\ HSPI (id=1) VSPI (id=2)
|
||
===== =========== ============
|
||
sck 14 18
|
||
mosi 13 23
|
||
miso 12 19
|
||
===== =========== ============
|
||
|
||
Hardware SPI is accessed via the :ref:`machine.SPI <machine.SPI>` class and
|
||
has the same methods as software SPI above::
|
||
|
||
from machine import Pin, SPI
|
||
|
||
hspi = SPI(1, 10000000)
|
||
hspi = SPI(1, 10000000, sck=Pin(14), mosi=Pin(13), miso=Pin(12))
|
||
vspi = SPI(2, baudrate=80000000, polarity=0, phase=0, bits=8, firstbit=0, sck=Pin(18), mosi=Pin(23), miso=Pin(19))
|
||
|
||
Software I2C bus
|
||
----------------
|
||
|
||
Software I2C (using bit-banging) works on all output-capable pins, and is
|
||
accessed via the :ref:`machine.SoftI2C <machine.SoftI2C>` class::
|
||
|
||
from machine import Pin, SoftI2C
|
||
|
||
i2c = SoftI2C(scl=Pin(5), sda=Pin(4), freq=100000)
|
||
|
||
i2c.scan() # scan for devices
|
||
|
||
i2c.readfrom(0x3a, 4) # read 4 bytes from device with address 0x3a
|
||
i2c.writeto(0x3a, '12') # write '12' to device with address 0x3a
|
||
|
||
buf = bytearray(10) # create a buffer with 10 bytes
|
||
i2c.writeto(0x3a, buf) # write the given buffer to the peripheral
|
||
|
||
Hardware I2C bus
|
||
----------------
|
||
|
||
There are two hardware I2C peripherals with identifiers 0 and 1. Any available
|
||
output-capable pins can be used for SCL and SDA but the defaults are given
|
||
below.
|
||
|
||
===== =========== ============
|
||
\ I2C(0) I2C(1)
|
||
===== =========== ============
|
||
scl 18 25
|
||
sda 19 26
|
||
===== =========== ============
|
||
|
||
The driver is accessed via the :ref:`machine.I2C <machine.I2C>` class and
|
||
has the same methods as software I2C above::
|
||
|
||
from machine import Pin, I2C
|
||
|
||
i2c = I2C(0)
|
||
i2c = I2C(1, scl=Pin(5), sda=Pin(4), freq=400000)
|
||
|
||
I2S bus
|
||
-------
|
||
|
||
See :ref:`machine.I2S <machine.I2S>`. ::
|
||
|
||
from machine import I2S, Pin
|
||
|
||
i2s = I2S(0, sck=Pin(13), ws=Pin(14), sd=Pin(34), mode=I2S.TX, bits=16, format=I2S.STEREO, rate=44100, ibuf=40000) # create I2S object
|
||
i2s.write(buf) # write buffer of audio samples to I2S device
|
||
|
||
i2s = I2S(1, sck=Pin(33), ws=Pin(25), sd=Pin(32), mode=I2S.RX, bits=16, format=I2S.MONO, rate=22050, ibuf=40000) # create I2S object
|
||
i2s.readinto(buf) # fill buffer with audio samples from I2S device
|
||
|
||
The I2S class is currently available as a Technical Preview. During the preview period, feedback from
|
||
users is encouraged. Based on this feedback, the I2S class API and implementation may be changed.
|
||
|
||
ESP32 has two I2S buses with id=0 and id=1
|
||
|
||
Real time clock (RTC)
|
||
---------------------
|
||
|
||
See :ref:`machine.RTC <machine.RTC>` ::
|
||
|
||
from machine import RTC
|
||
|
||
rtc = RTC()
|
||
rtc.datetime((2017, 8, 23, 1, 12, 48, 0, 0)) # set a specific date and time
|
||
rtc.datetime() # get date and time
|
||
|
||
WDT (Watchdog timer)
|
||
--------------------
|
||
|
||
See :ref:`machine.WDT <machine.WDT>`. ::
|
||
|
||
from machine import WDT
|
||
|
||
# enable the WDT with a timeout of 5s (1s is the minimum)
|
||
wdt = WDT(timeout=5000)
|
||
wdt.feed()
|
||
|
||
.. _Deep_sleep_mode:
|
||
|
||
Deep-sleep mode
|
||
---------------
|
||
|
||
The following code can be used to sleep, wake and check the reset cause::
|
||
|
||
import machine
|
||
|
||
# check if the device woke from a deep sleep
|
||
if machine.reset_cause() == machine.DEEPSLEEP_RESET:
|
||
print('woke from a deep sleep')
|
||
|
||
# put the device to sleep for 10 seconds
|
||
machine.deepsleep(10000)
|
||
|
||
Notes:
|
||
|
||
* Calling ``deepsleep()`` without an argument will put the device to sleep
|
||
indefinitely
|
||
* A software reset does not change the reset cause
|
||
|
||
Some ESP32 pins (0, 2, 4, 12-15, 25-27, 32-39) are connected to the RTC during
|
||
deep-sleep and can be used to wake the device with the ``wake_on_`` functions in
|
||
the :mod:`esp32` module. The output-capable RTC pins (all except 34-39) will
|
||
also retain their pull-up or pull-down resistor configuration when entering
|
||
deep-sleep.
|
||
|
||
If the pull resistors are not actively required during deep-sleep and are likely
|
||
to cause current leakage (for example a pull-up resistor is connected to ground
|
||
through a switch), then they should be disabled to save power before entering
|
||
deep-sleep mode::
|
||
|
||
from machine import Pin, deepsleep
|
||
|
||
# configure input RTC pin with pull-up on boot
|
||
pin = Pin(2, Pin.IN, Pin.PULL_UP)
|
||
|
||
# disable pull-up and put the device to sleep for 10 seconds
|
||
pin.init(pull=None)
|
||
machine.deepsleep(10000)
|
||
|
||
Output-configured RTC pins will also retain their output direction and level in
|
||
deep-sleep if pad hold is enabled with the ``hold=True`` argument to
|
||
``Pin.init()``.
|
||
|
||
Non-RTC GPIO pins will be disconnected by default on entering deep-sleep.
|
||
Configuration of non-RTC pins - including output level - can be retained by
|
||
enabling pad hold on the pin and enabling GPIO pad hold during deep-sleep::
|
||
|
||
from machine import Pin, deepsleep
|
||
import esp32
|
||
|
||
opin = Pin(19, Pin.OUT, value=1, hold=True) # hold output level
|
||
ipin = Pin(21, Pin.IN, Pin.PULL_UP, hold=True) # hold pull-up
|
||
|
||
# enable pad hold in deep-sleep for non-RTC GPIO
|
||
esp32.gpio_deep_sleep_hold(True)
|
||
|
||
# put the device to sleep for 10 seconds
|
||
deepsleep(10000)
|
||
|
||
The pin configuration - including the pad hold - will be retained on wake from
|
||
sleep. See :ref:`Pins_and_GPIO` above for a further discussion of pad holding.
|
||
|
||
SD card
|
||
-------
|
||
|
||
See :ref:`machine.SDCard <machine.SDCard>`. ::
|
||
|
||
import machine, os
|
||
|
||
# Slot 2 uses pins sck=18, cs=5, miso=19, mosi=23
|
||
sd = machine.SDCard(slot=2)
|
||
os.mount(sd, '/sd') # mount
|
||
|
||
os.listdir('/sd') # list directory contents
|
||
|
||
os.umount('/sd') # eject
|
||
|
||
RMT
|
||
---
|
||
|
||
The RMT is ESP32-specific and allows generation of accurate digital pulses with
|
||
12.5ns resolution. See :ref:`esp32.RMT <esp32.RMT>` for details. Usage is::
|
||
|
||
import esp32
|
||
from machine import Pin
|
||
|
||
r = esp32.RMT(0, pin=Pin(18), clock_div=8)
|
||
r # RMT(channel=0, pin=18, source_freq=80000000, clock_div=8)
|
||
# The channel resolution is 100ns (1/(source_freq/clock_div)).
|
||
r.write_pulses((1, 20, 2, 40), 0) # Send 0 for 100ns, 1 for 2000ns, 0 for 200ns, 1 for 4000ns
|
||
|
||
OneWire driver
|
||
--------------
|
||
|
||
The OneWire driver is implemented in software and works on all pins::
|
||
|
||
from machine import Pin
|
||
import onewire
|
||
|
||
ow = onewire.OneWire(Pin(12)) # create a OneWire bus on GPIO12
|
||
ow.scan() # return a list of devices on the bus
|
||
ow.reset() # reset the bus
|
||
ow.readbyte() # read a byte
|
||
ow.writebyte(0x12) # write a byte on the bus
|
||
ow.write('123') # write bytes on the bus
|
||
ow.select_rom(b'12345678') # select a specific device by its ROM code
|
||
|
||
There is a specific driver for DS18S20 and DS18B20 devices::
|
||
|
||
import time, ds18x20
|
||
ds = ds18x20.DS18X20(ow)
|
||
roms = ds.scan()
|
||
ds.convert_temp()
|
||
time.sleep_ms(750)
|
||
for rom in roms:
|
||
print(ds.read_temp(rom))
|
||
|
||
Be sure to put a 4.7k pull-up resistor on the data line. Note that
|
||
the ``convert_temp()`` method must be called each time you want to
|
||
sample the temperature.
|
||
|
||
NeoPixel and APA106 driver
|
||
--------------------------
|
||
|
||
Use the ``neopixel`` and ``apa106`` modules::
|
||
|
||
from machine import Pin
|
||
from neopixel import NeoPixel
|
||
|
||
pin = Pin(0, Pin.OUT) # set GPIO0 to output to drive NeoPixels
|
||
np = NeoPixel(pin, 8) # create NeoPixel driver on GPIO0 for 8 pixels
|
||
np[0] = (255, 255, 255) # set the first pixel to white
|
||
np.write() # write data to all pixels
|
||
r, g, b = np[0] # get first pixel colour
|
||
|
||
|
||
The APA106 driver extends NeoPixel, but internally uses a different colour order::
|
||
|
||
from apa106 import APA106
|
||
ap = APA106(pin, 8)
|
||
r, g, b = ap[0]
|
||
|
||
.. Warning::
|
||
By default ``NeoPixel`` is configured to control the more popular *800kHz*
|
||
units. It is possible to use alternative timing to control other (typically
|
||
400kHz) devices by passing ``timing=0`` when constructing the
|
||
``NeoPixel`` object.
|
||
|
||
For low-level driving of a NeoPixel see `machine.bitstream`.
|
||
This low-level driver uses an RMT channel by default. To configure this see
|
||
`RMT.bitstream_channel`.
|
||
|
||
APA102 (DotStar) uses a different driver as it has an additional clock pin.
|
||
|
||
Capacitive touch
|
||
----------------
|
||
|
||
Use the ``TouchPad`` class in the ``machine`` module::
|
||
|
||
from machine import TouchPad, Pin
|
||
|
||
t = TouchPad(Pin(14))
|
||
t.read() # Returns a smaller number when touched
|
||
|
||
``TouchPad.read`` returns a value relative to the capacitive variation. Small numbers (typically in
|
||
the *tens*) are common when a pin is touched, larger numbers (above *one thousand*) when
|
||
no touch is present. However the values are *relative* and can vary depending on the board
|
||
and surrounding composition so some calibration may be required.
|
||
|
||
There are ten capacitive touch-enabled pins that can be used on the ESP32: 0, 2, 4, 12, 13
|
||
14, 15, 27, 32, 33. Trying to assign to any other pins will result in a ``ValueError``.
|
||
|
||
Note that TouchPads can be used to wake an ESP32 from sleep::
|
||
|
||
import machine
|
||
from machine import TouchPad, Pin
|
||
import esp32
|
||
|
||
t = TouchPad(Pin(14))
|
||
t.config(500) # configure the threshold at which the pin is considered touched
|
||
esp32.wake_on_touch(True)
|
||
machine.lightsleep() # put the MCU to sleep until a touchpad is touched
|
||
|
||
For more details on touchpads refer to `Espressif Touch Sensor
|
||
<https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/peripherals/touch_pad.html>`_.
|
||
|
||
|
||
DHT driver
|
||
----------
|
||
|
||
The DHT driver is implemented in software and works on all pins::
|
||
|
||
import dht
|
||
import machine
|
||
|
||
d = dht.DHT11(machine.Pin(4))
|
||
d.measure()
|
||
d.temperature() # eg. 23 (°C)
|
||
d.humidity() # eg. 41 (% RH)
|
||
|
||
d = dht.DHT22(machine.Pin(4))
|
||
d.measure()
|
||
d.temperature() # eg. 23.6 (°C)
|
||
d.humidity() # eg. 41.3 (% RH)
|
||
|
||
WebREPL (web browser interactive prompt)
|
||
----------------------------------------
|
||
|
||
WebREPL (REPL over WebSockets, accessible via a web browser) is an
|
||
experimental feature available in ESP32 port. Download web client
|
||
from https://github.com/micropython/webrepl (hosted version available
|
||
at http://micropython.org/webrepl), and configure it by executing::
|
||
|
||
import webrepl_setup
|
||
|
||
and following on-screen instructions. After reboot, it will be available
|
||
for connection. If you disabled automatic start-up on boot, you may
|
||
run configured daemon on demand using::
|
||
|
||
import webrepl
|
||
webrepl.start()
|
||
|
||
# or, start with a specific password
|
||
webrepl.start(password='mypass')
|
||
|
||
The WebREPL daemon listens on all active interfaces, which can be STA or
|
||
AP. This allows you to connect to the ESP32 via a router (the STA
|
||
interface) or directly when connected to its access point.
|
||
|
||
In addition to terminal/command prompt access, WebREPL also has provision
|
||
for file transfer (both upload and download). The web client has buttons for
|
||
the corresponding functions, or you can use the command-line client
|
||
``webrepl_cli.py`` from the repository above.
|
||
|
||
See the MicroPython forum for other community-supported alternatives
|
||
to transfer files to an ESP32 board.
|