9d91111b1b
This started while adding USB MIDI support (and descriptor support is in this change.) When seeing that I'd have to implement the MIDI class logic twice, once for atmel-samd and once for nrf, I decided to refactor the USB stack so its shared across ports. This has led to a number of changes that remove items from the ports folder and move them into supervisor. Furthermore, we had external SPI flash support for nrf pending so I factored out the connection between the usb stack and the flash API as well. This PR also includes the QSPI support for nRF.
355 lines
12 KiB
C
355 lines
12 KiB
C
/*
|
|
* This file is part of the MicroPython project, http://micropython.org/
|
|
*
|
|
* The MIT License (MIT)
|
|
*
|
|
* Copyright (c) 2016 Scott Shawcroft
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*/
|
|
|
|
#include "shared-bindings/busio/SPI.h"
|
|
#include "py/mperrno.h"
|
|
#include "py/runtime.h"
|
|
|
|
#include "hpl_sercom_config.h"
|
|
#include "peripheral_clk_config.h"
|
|
|
|
#include "boards/board.h"
|
|
#include "common-hal/microcontroller/Pin.h"
|
|
#include "hal/include/hal_gpio.h"
|
|
#include "hal/include/hal_spi_m_sync.h"
|
|
#include "hal/include/hpl_spi_m_sync.h"
|
|
#include "supervisor/shared/rgb_led_status.h"
|
|
|
|
#include "samd/dma.h"
|
|
#include "samd/sercom.h"
|
|
|
|
bool never_reset_sercoms[SERCOM_INST_NUM];
|
|
|
|
void never_reset_sercom(Sercom* sercom) {
|
|
// Reset all SERCOMs except the ones being used by on-board devices.
|
|
Sercom *sercom_instances[SERCOM_INST_NUM] = SERCOM_INSTS;
|
|
for (int i = 0; i < SERCOM_INST_NUM; i++) {
|
|
if (sercom_instances[i] == sercom) {
|
|
never_reset_sercoms[i] = true;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
void reset_sercoms(void) {
|
|
// Reset all SERCOMs except the ones being used by on-board devices.
|
|
Sercom *sercom_instances[SERCOM_INST_NUM] = SERCOM_INSTS;
|
|
for (int i = 0; i < SERCOM_INST_NUM; i++) {
|
|
if (never_reset_sercoms[i]) {
|
|
continue;
|
|
}
|
|
#ifdef MICROPY_HW_APA102_SERCOM
|
|
if (sercom_instances[i] == MICROPY_HW_APA102_SERCOM) {
|
|
continue;
|
|
}
|
|
#endif
|
|
#ifdef CIRCUITPY_DISPLAYIO
|
|
// TODO(tannewt): Make this dynamic.
|
|
if (sercom_instances[i] == board_display_obj.bus.spi_desc.dev.prvt) {
|
|
continue;
|
|
}
|
|
#endif
|
|
// SWRST is same for all modes of SERCOMs.
|
|
sercom_instances[i]->SPI.CTRLA.bit.SWRST = 1;
|
|
}
|
|
}
|
|
|
|
|
|
void common_hal_busio_spi_construct(busio_spi_obj_t *self,
|
|
const mcu_pin_obj_t * clock, const mcu_pin_obj_t * mosi,
|
|
const mcu_pin_obj_t * miso) {
|
|
Sercom* sercom = NULL;
|
|
uint8_t sercom_index;
|
|
uint32_t clock_pinmux = 0;
|
|
bool mosi_none = mosi == mp_const_none;
|
|
bool miso_none = miso == mp_const_none;
|
|
uint32_t mosi_pinmux = 0;
|
|
uint32_t miso_pinmux = 0;
|
|
uint8_t clock_pad = 0;
|
|
uint8_t mosi_pad = 0;
|
|
uint8_t miso_pad = 0;
|
|
uint8_t dopo = 255;
|
|
#ifdef PIN_PC19
|
|
if (miso == &pin_PC19) {
|
|
if (mosi == &pin_PB30 && clock == &pin_PC18) {
|
|
sercom = SERCOM4;
|
|
sercom_index = 4;
|
|
clock_pinmux = MUX_F;
|
|
mosi_pinmux = MUX_F;
|
|
miso_pinmux = MUX_F;
|
|
clock_pad = 3;
|
|
mosi_pad = 2;
|
|
miso_pad = 0;
|
|
dopo = samd_peripherals_get_spi_dopo(clock_pad, mosi_pad);
|
|
}
|
|
// Error, leave SERCOM unset to throw an exception later.
|
|
} else {
|
|
#endif
|
|
for (int i = 0; i < NUM_SERCOMS_PER_PIN; i++) {
|
|
sercom_index = clock->sercom[i].index; // 2 for SERCOM2, etc.
|
|
if (sercom_index >= SERCOM_INST_NUM) {
|
|
continue;
|
|
}
|
|
Sercom* potential_sercom = sercom_insts[sercom_index];
|
|
if (
|
|
#if defined(MICROPY_HW_APA102_SCK) && defined(MICROPY_HW_APA102_MOSI) && !defined(CIRCUITPY_BITBANG_APA102)
|
|
(potential_sercom->SPI.CTRLA.bit.ENABLE != 0 &&
|
|
potential_sercom != status_apa102.spi_desc.dev.prvt &&
|
|
!apa102_sck_in_use)) {
|
|
#else
|
|
potential_sercom->SPI.CTRLA.bit.ENABLE != 0) {
|
|
#endif
|
|
continue;
|
|
}
|
|
clock_pinmux = PINMUX(clock->number, (i == 0) ? MUX_C : MUX_D);
|
|
clock_pad = clock->sercom[i].pad;
|
|
if (!samd_peripherals_valid_spi_clock_pad(clock_pad)) {
|
|
continue;
|
|
}
|
|
for (int j = 0; j < NUM_SERCOMS_PER_PIN; j++) {
|
|
if (!mosi_none) {
|
|
if (sercom_index == mosi->sercom[j].index) {
|
|
mosi_pinmux = PINMUX(mosi->number, (j == 0) ? MUX_C : MUX_D);
|
|
mosi_pad = mosi->sercom[j].pad;
|
|
dopo = samd_peripherals_get_spi_dopo(clock_pad, mosi_pad);
|
|
if (dopo > 0x3) {
|
|
continue; // pad combination not possible
|
|
}
|
|
if (miso_none) {
|
|
sercom = potential_sercom;
|
|
break;
|
|
}
|
|
} else {
|
|
continue;
|
|
}
|
|
}
|
|
if (!miso_none) {
|
|
for (int k = 0; k < NUM_SERCOMS_PER_PIN; k++) {
|
|
if (sercom_index == miso->sercom[k].index) {
|
|
miso_pinmux = PINMUX(miso->number, (k == 0) ? MUX_C : MUX_D);
|
|
miso_pad = miso->sercom[k].pad;
|
|
sercom = potential_sercom;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
if (sercom != NULL) {
|
|
break;
|
|
}
|
|
}
|
|
if (sercom != NULL) {
|
|
break;
|
|
}
|
|
}
|
|
#ifdef PIN_PC19
|
|
}
|
|
#endif
|
|
if (sercom == NULL) {
|
|
mp_raise_ValueError(translate("Invalid pins"));
|
|
}
|
|
|
|
// Set up SPI clocks on SERCOM.
|
|
samd_peripherals_sercom_clock_init(sercom, sercom_index);
|
|
|
|
#if defined(MICROPY_HW_APA102_SCK) && defined(MICROPY_HW_APA102_MOSI) && !defined(CIRCUITPY_BITBANG_APA102)
|
|
// if we're re-using the dotstar sercom, make sure it is disabled or the init will fail out
|
|
hri_sercomspi_clear_CTRLA_ENABLE_bit(sercom);
|
|
#endif
|
|
if (spi_m_sync_init(&self->spi_desc, sercom) != ERR_NONE) {
|
|
mp_raise_OSError(MP_EIO);
|
|
}
|
|
|
|
// Pads must be set after spi_m_sync_init(), which uses default values from
|
|
// the prototypical SERCOM.
|
|
hri_sercomspi_write_CTRLA_DOPO_bf(sercom, dopo);
|
|
hri_sercomspi_write_CTRLA_DIPO_bf(sercom, miso_pad);
|
|
|
|
// Always start at 250khz which is what SD cards need. They are sensitive to
|
|
// SPI bus noise before they are put into SPI mode.
|
|
uint8_t baud_value = samd_peripherals_spi_baudrate_to_baud_reg_value(250000);
|
|
if (spi_m_sync_set_baudrate(&self->spi_desc, baud_value) != ERR_NONE) {
|
|
// spi_m_sync_set_baudrate does not check for validity, just whether the device is
|
|
// busy or not
|
|
mp_raise_OSError(MP_EIO);
|
|
}
|
|
|
|
gpio_set_pin_direction(clock->number, GPIO_DIRECTION_OUT);
|
|
gpio_set_pin_pull_mode(clock->number, GPIO_PULL_OFF);
|
|
gpio_set_pin_function(clock->number, clock_pinmux);
|
|
claim_pin(clock);
|
|
self->clock_pin = clock->number;
|
|
|
|
if (mosi_none) {
|
|
self->MOSI_pin = NO_PIN;
|
|
} else {
|
|
gpio_set_pin_direction(mosi->number, GPIO_DIRECTION_OUT);
|
|
gpio_set_pin_pull_mode(mosi->number, GPIO_PULL_OFF);
|
|
gpio_set_pin_function(mosi->number, mosi_pinmux);
|
|
self->MOSI_pin = mosi->number;
|
|
claim_pin(mosi);
|
|
}
|
|
|
|
if (miso_none) {
|
|
self->MISO_pin = NO_PIN;
|
|
} else {
|
|
gpio_set_pin_direction(miso->number, GPIO_DIRECTION_IN);
|
|
gpio_set_pin_pull_mode(miso->number, GPIO_PULL_OFF);
|
|
gpio_set_pin_function(miso->number, miso_pinmux);
|
|
self->MISO_pin = miso->number;
|
|
claim_pin(miso);
|
|
}
|
|
|
|
spi_m_sync_enable(&self->spi_desc);
|
|
}
|
|
|
|
void common_hal_busio_spi_never_reset(busio_spi_obj_t *self) {
|
|
never_reset_sercom(self->spi_desc.dev.prvt);
|
|
|
|
never_reset_pin_number(self->clock_pin);
|
|
never_reset_pin_number(self->MOSI_pin);
|
|
never_reset_pin_number(self->MISO_pin);
|
|
}
|
|
|
|
bool common_hal_busio_spi_deinited(busio_spi_obj_t *self) {
|
|
return self->clock_pin == NO_PIN;
|
|
}
|
|
|
|
void common_hal_busio_spi_deinit(busio_spi_obj_t *self) {
|
|
if (common_hal_busio_spi_deinited(self)) {
|
|
return;
|
|
}
|
|
spi_m_sync_disable(&self->spi_desc);
|
|
spi_m_sync_deinit(&self->spi_desc);
|
|
reset_pin_number(self->clock_pin);
|
|
reset_pin_number(self->MOSI_pin);
|
|
reset_pin_number(self->MISO_pin);
|
|
self->clock_pin = NO_PIN;
|
|
}
|
|
|
|
bool common_hal_busio_spi_configure(busio_spi_obj_t *self,
|
|
uint32_t baudrate, uint8_t polarity, uint8_t phase, uint8_t bits) {
|
|
uint8_t baud_reg_value = samd_peripherals_spi_baudrate_to_baud_reg_value(baudrate);
|
|
|
|
void * hw = self->spi_desc.dev.prvt;
|
|
// If the settings are already what we want then don't reset them.
|
|
if (hri_sercomspi_get_CTRLA_CPHA_bit(hw) == phase &&
|
|
hri_sercomspi_get_CTRLA_CPOL_bit(hw) == polarity &&
|
|
hri_sercomspi_read_CTRLB_CHSIZE_bf(hw) == ((uint32_t)bits - 8) &&
|
|
hri_sercomspi_read_BAUD_BAUD_bf(hw) == baud_reg_value) {
|
|
return true;
|
|
}
|
|
|
|
// Disable, set values (most or all are enable-protected), and re-enable.
|
|
spi_m_sync_disable(&self->spi_desc);
|
|
hri_sercomspi_wait_for_sync(hw, SERCOM_SPI_SYNCBUSY_MASK);
|
|
|
|
hri_sercomspi_write_CTRLA_CPHA_bit(hw, phase);
|
|
hri_sercomspi_write_CTRLA_CPOL_bit(hw, polarity);
|
|
hri_sercomspi_write_CTRLB_CHSIZE_bf(hw, bits - 8);
|
|
hri_sercomspi_write_BAUD_BAUD_bf(hw, baud_reg_value);
|
|
hri_sercomspi_wait_for_sync(hw, SERCOM_SPI_SYNCBUSY_MASK);
|
|
|
|
spi_m_sync_enable(&self->spi_desc);
|
|
hri_sercomspi_wait_for_sync(hw, SERCOM_SPI_SYNCBUSY_MASK);
|
|
|
|
return true;
|
|
}
|
|
|
|
bool common_hal_busio_spi_try_lock(busio_spi_obj_t *self) {
|
|
bool grabbed_lock = false;
|
|
CRITICAL_SECTION_ENTER()
|
|
if (!self->has_lock) {
|
|
grabbed_lock = true;
|
|
self->has_lock = true;
|
|
}
|
|
CRITICAL_SECTION_LEAVE();
|
|
return grabbed_lock;
|
|
}
|
|
|
|
bool common_hal_busio_spi_has_lock(busio_spi_obj_t *self) {
|
|
return self->has_lock;
|
|
}
|
|
|
|
void common_hal_busio_spi_unlock(busio_spi_obj_t *self) {
|
|
self->has_lock = false;
|
|
}
|
|
|
|
bool common_hal_busio_spi_write(busio_spi_obj_t *self,
|
|
const uint8_t *data, size_t len) {
|
|
if (len == 0) {
|
|
return true;
|
|
}
|
|
int32_t status;
|
|
if (len >= 16) {
|
|
status = sercom_dma_write(self->spi_desc.dev.prvt, data, len);
|
|
} else {
|
|
struct io_descriptor *spi_io;
|
|
spi_m_sync_get_io_descriptor(&self->spi_desc, &spi_io);
|
|
status = spi_io->write(spi_io, data, len);
|
|
}
|
|
return status >= 0; // Status is number of chars read or an error code < 0.
|
|
}
|
|
|
|
bool common_hal_busio_spi_read(busio_spi_obj_t *self,
|
|
uint8_t *data, size_t len, uint8_t write_value) {
|
|
if (len == 0) {
|
|
return true;
|
|
}
|
|
int32_t status;
|
|
if (len >= 16) {
|
|
status = sercom_dma_read(self->spi_desc.dev.prvt, data, len, write_value);
|
|
} else {
|
|
self->spi_desc.dev.dummy_byte = write_value;
|
|
|
|
struct io_descriptor *spi_io;
|
|
spi_m_sync_get_io_descriptor(&self->spi_desc, &spi_io);
|
|
|
|
status = spi_io->read(spi_io, data, len);
|
|
}
|
|
return status >= 0; // Status is number of chars read or an error code < 0.
|
|
}
|
|
|
|
bool common_hal_busio_spi_transfer(busio_spi_obj_t *self, uint8_t *data_out, uint8_t *data_in, size_t len) {
|
|
if (len == 0) {
|
|
return true;
|
|
}
|
|
int32_t status;
|
|
if (len >= 16) {
|
|
status = sercom_dma_transfer(self->spi_desc.dev.prvt, data_out, data_in, len);
|
|
} else {
|
|
struct spi_xfer xfer;
|
|
xfer.txbuf = data_out;
|
|
xfer.rxbuf = data_in;
|
|
xfer.size = len;
|
|
status = spi_m_sync_transfer(&self->spi_desc, &xfer);
|
|
}
|
|
return status >= 0; // Status is number of chars read or an error code < 0.
|
|
}
|
|
|
|
uint32_t common_hal_busio_spi_get_frequency(busio_spi_obj_t* self) {
|
|
return samd_peripherals_spi_baud_reg_value_to_baudrate(hri_sercomspi_read_BAUD_reg(self->spi_desc.dev.prvt));
|
|
}
|