circuitpython/stmhal/boards/STM32F439/mpconfigboard.h

86 lines
3.2 KiB
C

#define MICROPY_HW_BOARD_NAME "CustomPCB"
#define MICROPY_HW_MCU_NAME "STM32F439"
#define MICROPY_HW_HAS_SWITCH (0)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1) //works with no SD card too
#define MICROPY_HW_HAS_MMA7660 (0)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (0)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_CAN (1)
// SD card detect switch
#if MICROPY_HW_HAS_SDCARD
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)
#endif
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8) //divide external clock by this to get 1MHz
#define MICROPY_HW_CLK_PLLN (384) //this number is the PLL clock in MHz
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) //divide PLL clock by this to get core clock
#define MICROPY_HW_CLK_PLLQ (8) //divide core clock by this to get 48MHz
// UART config
#define MICROPY_HW_UART1_PORT (GPIOA)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
#define MICROPY_HW_UART2_PORT (GPIOD)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_5 | GPIO_PIN_6)
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
#define MICROPY_HW_UART3_PORT (GPIOD)
#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9)
#define MICROPY_HW_UART3_RTS (GPIO_PIN_12)
#define MICROPY_HW_UART3_CTS (GPIO_PIN_11)
#define MICROPY_HW_UART4_PORT (GPIOA)
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
#define MICROPY_HW_UART6_PORT (GPIOC)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_A8)
#define MICROPY_HW_I2C1_SDA (pin_C9)
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#if defined(USE_USB_HS_IN_FS)
// The HS USB uses B14 & B15 for D- and D+
#else
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
#endif
#define MICROPY_HW_SPI3_NSS (pin_E11)
#define MICROPY_HW_SPI3_SCK (pin_E12)
#define MICROPY_HW_SPI3_MISO (pin_E13)
#define MICROPY_HW_SPI3_MOSI (pin_E14)
//#define MICROPY_HW_SPI4_NSS (pin_E11)
//#define MICROPY_HW_SPI4_SCK (pin_E12)
//#define MICROPY_HW_SPI4_MISO (pin_E13)
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
//#define MICROPY_HW_SPI5_NSS (pin_F6)
//#define MICROPY_HW_SPI5_SCK (pin_F7)
//#define MICROPY_HW_SPI5_MISO (pin_F8)
//#define MICROPY_HW_SPI5_MOSI (pin_F9)
//#define MICROPY_HW_SPI6_NSS (pin_G8)
//#define MICROPY_HW_SPI6_SCK (pin_G13)
//#define MICROPY_HW_SPI6_MISO (pin_G12)
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)