173 lines
6.4 KiB
ReStructuredText
173 lines
6.4 KiB
ReStructuredText
.. currentmodule:: machine
|
|
.. _machine.I2C:
|
|
|
|
class I2C -- a two-wire serial protocol
|
|
=======================================
|
|
|
|
I2C is a two-wire protocol for communicating between devices. At the physical
|
|
level it consists of 2 wires: SCL and SDA, the clock and data lines respectively.
|
|
|
|
I2C objects are created attached to a specific bus. They can be initialised
|
|
when created, or initialised later on.
|
|
|
|
Printing the I2C object gives you information about its configuration.
|
|
|
|
Example usage::
|
|
|
|
from machine import I2C
|
|
|
|
i2c = I2C(freq=400000) # create I2C peripheral at frequency of 400kHz
|
|
# depending on the port, extra parameters may be required
|
|
# to select the peripheral and/or pins to use
|
|
|
|
i2c.scan() # scan for slaves, returning a list of 7-bit addresses
|
|
|
|
i2c.writeto(42, b'123') # write 3 bytes to slave with 7-bit address 42
|
|
i2c.readfrom(42, 4) # read 4 bytes from slave with 7-bit address 42
|
|
|
|
i2c.readfrom_mem(42, 8, 3) # read 3 bytes from memory of slave 42,
|
|
# starting at memory-address 8 in the slave
|
|
i2c.writeto_mem(42, 2, b'\x10') # write 1 byte to memory of slave 42
|
|
# starting at address 2 in the slave
|
|
|
|
Constructors
|
|
------------
|
|
|
|
.. class:: I2C(id=-1, \*, scl, sda, freq=400000)
|
|
|
|
Construct and return a new I2C object using the following parameters:
|
|
|
|
- `id` identifies the particular I2C peripheral. The default
|
|
value of -1 selects a software implementation of I2C which can
|
|
work (in most cases) with arbitrary pins for SCL and SDA.
|
|
If `id` is -1 then `scl` and `sda` must be specified. Other
|
|
allowed values for `id` depend on the particular port/board,
|
|
and specifying `scl` and `sda` may or may not be required or
|
|
allowed in this case.
|
|
- `scl` should be a pin object specifying the pin to use for SCL.
|
|
- `sda` should be a pin object specifying the pin to use for SDA.
|
|
- `freq` should be an integer which sets the maximum frequency
|
|
for SCL.
|
|
|
|
General Methods
|
|
---------------
|
|
|
|
.. method:: I2C.init(scl, sda, \*, freq=400000)
|
|
|
|
Initialise the I2C bus with the given arguments:
|
|
|
|
- `scl` is a pin object for the SCL line
|
|
- `sda` is a pin object for the SDA line
|
|
- `freq` is the SCL clock rate
|
|
|
|
.. method:: I2C.deinit()
|
|
|
|
Turn off the I2C bus.
|
|
|
|
Availability: WiPy.
|
|
|
|
.. method:: I2C.scan()
|
|
|
|
Scan all I2C addresses between 0x08 and 0x77 inclusive and return a list of
|
|
those that respond. A device responds if it pulls the SDA line low after
|
|
its address (including a write bit) is sent on the bus.
|
|
|
|
Primitive I2C operations
|
|
------------------------
|
|
|
|
The following methods implement the primitive I2C master bus operations and can
|
|
be combined to make any I2C transaction. They are provided if you need more
|
|
control over the bus, otherwise the standard methods (see below) can be used.
|
|
|
|
.. method:: I2C.start()
|
|
|
|
Generate a START condition on the bus (SDA transitions to low while SCL is high).
|
|
|
|
Availability: ESP8266.
|
|
|
|
.. method:: I2C.stop()
|
|
|
|
Generate a STOP condition on the bus (SDA transitions to high while SCL is high).
|
|
|
|
Availability: ESP8266.
|
|
|
|
.. method:: I2C.readinto(buf, nack=True)
|
|
|
|
Reads bytes from the bus and stores them into `buf`. The number of bytes
|
|
read is the length of `buf`. An ACK will be sent on the bus after
|
|
receiving all but the last byte. After the last byte is received, if `nack`
|
|
is true then a NACK will be sent, otherwise an ACK will be sent (and in this
|
|
case the slave assumes more bytes are going to be read in a later call).
|
|
|
|
Availability: ESP8266.
|
|
|
|
.. method:: I2C.write(buf)
|
|
|
|
Write the bytes from `buf` to the bus. Checks that an ACK is received
|
|
after each byte and stops transmitting the remaining bytes if a NACK is
|
|
received. The function returns the number of ACKs that were received.
|
|
|
|
Availability: ESP8266.
|
|
|
|
Standard bus operations
|
|
-----------------------
|
|
|
|
The following methods implement the standard I2C master read and write
|
|
operations that target a given slave device.
|
|
|
|
.. method:: I2C.readfrom(addr, nbytes, stop=True)
|
|
|
|
Read `nbytes` from the slave specified by `addr`.
|
|
If `stop` is true then a STOP condition is generated at the end of the transfer.
|
|
Returns a `bytes` object with the data read.
|
|
|
|
.. method:: I2C.readfrom_into(addr, buf, stop=True)
|
|
|
|
Read into `buf` from the slave specified by `addr`.
|
|
The number of bytes read will be the length of `buf`.
|
|
If `stop` is true then a STOP condition is generated at the end of the transfer.
|
|
|
|
The method returns `None`.
|
|
|
|
.. method:: I2C.writeto(addr, buf, stop=True)
|
|
|
|
Write the bytes from `buf` to the slave specified by `addr`. If a
|
|
NACK is received following the write of a byte from `buf` then the
|
|
remaining bytes are not sent. If `stop` is true then a STOP condition is
|
|
generated at the end of the transfer, even if a NACK is received.
|
|
The function returns the number of ACKs that were received.
|
|
|
|
Memory operations
|
|
-----------------
|
|
|
|
Some I2C devices act as a memory device (or set of registers) that can be read
|
|
from and written to. In this case there are two addresses associated with an
|
|
I2C transaction: the slave address and the memory address. The following
|
|
methods are convenience functions to communicate with such devices.
|
|
|
|
.. method:: I2C.readfrom_mem(addr, memaddr, nbytes, \*, addrsize=8)
|
|
|
|
Read `nbytes` from the slave specified by `addr` starting from the memory
|
|
address specified by `memaddr`.
|
|
The argument `addrsize` specifies the address size in bits.
|
|
Returns a `bytes` object with the data read.
|
|
|
|
.. method:: I2C.readfrom_mem_into(addr, memaddr, buf, \*, addrsize=8)
|
|
|
|
Read into `buf` from the slave specified by `addr` starting from the
|
|
memory address specified by `memaddr`. The number of bytes read is the
|
|
length of `buf`.
|
|
The argument `addrsize` specifies the address size in bits (on ESP8266
|
|
this argument is not recognised and the address size is always 8 bits).
|
|
|
|
The method returns `None`.
|
|
|
|
.. method:: I2C.writeto_mem(addr, memaddr, buf, \*, addrsize=8)
|
|
|
|
Write `buf` to the slave specified by `addr` starting from the
|
|
memory address specified by `memaddr`.
|
|
The argument `addrsize` specifies the address size in bits (on ESP8266
|
|
this argument is not recognised and the address size is always 8 bits).
|
|
|
|
The method returns `None`.
|