162 lines
6.2 KiB
C
162 lines
6.2 KiB
C
#define MICROPY_HW_BOARD_NAME "F7DISC"
|
|
#define MICROPY_HW_MCU_NAME "STM32F746"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_ENABLE_SDCARD (1)
|
|
|
|
#define MICROPY_BOARD_EARLY_INIT STM32F7DISC_board_early_init
|
|
void STM32F7DISC_board_early_init(void);
|
|
|
|
// HSE is 25MHz
|
|
// VCOClock = HSE * PLLN / PLLM = 25 MHz * 384 / 25 = 384 MHz
|
|
// SYSCLK = VCOClock / PLLP = 384 MHz / 2 = 192 MHz
|
|
// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 384 MHz / 8 = 48 MHz
|
|
// Note: SDRAM requires SYSCLK <= 200MHz
|
|
// SYSCLK can be increased to 216MHz if SDRAM is disabled
|
|
#define MICROPY_HW_CLK_PLLM (25)
|
|
#define MICROPY_HW_CLK_PLLN (384)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (8)
|
|
|
|
// From the reference manual, for 2.7V to 3.6V
|
|
// 151-180 MHz => 5 wait states
|
|
// 181-210 MHz => 6 wait states
|
|
// 211-216 MHz => 7 wait states
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_6 // 181-210 MHz => 6 wait states
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_B7)
|
|
#define MICROPY_HW_UART6_TX (pin_C6)
|
|
#define MICROPY_HW_UART6_RX (pin_C7)
|
|
#define MICROPY_HW_UART7_TX (pin_F6)
|
|
#define MICROPY_HW_UART7_RX (pin_F7)
|
|
#define MICROPY_HW_UART_REPL PYB_UART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
|
|
#define MICROPY_HW_I2C3_SCL (pin_H7)
|
|
#define MICROPY_HW_I2C3_SDA (pin_H8)
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI2_NSS (pin_I0)
|
|
#define MICROPY_HW_SPI2_SCK (pin_I1)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
// CAN buses
|
|
#define MICROPY_HW_CAN1_TX (pin_B9)
|
|
#define MICROPY_HW_CAN1_RX (pin_B8)
|
|
#define MICROPY_HW_CAN2_TX (pin_B13)
|
|
#define MICROPY_HW_CAN2_RX (pin_B12)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_I11)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_I1) // green
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// SD card detect switch
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13)
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
|
|
|
|
// USB config (CN13 - USB OTG FS)
|
|
// The Hardware VBUS detect only works on pin PA9. The STM32F7 Discovery uses
|
|
// PA9 for VCP_TX functionality and connects the VBUS to pin J12 (so software
|
|
// only detect). So we don't define the VBUS detect pin since that requires PA9.
|
|
#define MICROPY_HW_USB_FS (1)
|
|
/*#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_J12)*/
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|
|
|
|
// Ethernet via RMII
|
|
#define MICROPY_HW_ETH_MDC (pin_C1)
|
|
#define MICROPY_HW_ETH_MDIO (pin_A2)
|
|
#define MICROPY_HW_ETH_RMII_REF_CLK (pin_A1)
|
|
#define MICROPY_HW_ETH_RMII_CRS_DV (pin_A7)
|
|
#define MICROPY_HW_ETH_RMII_RXD0 (pin_C4)
|
|
#define MICROPY_HW_ETH_RMII_RXD1 (pin_C5)
|
|
#define MICROPY_HW_ETH_RMII_RXER (pin_G2)
|
|
#define MICROPY_HW_ETH_RMII_TX_EN (pin_G11)
|
|
#define MICROPY_HW_ETH_RMII_TXD0 (pin_G13)
|
|
#define MICROPY_HW_ETH_RMII_TXD1 (pin_G14)
|
|
|
|
// SDRAM
|
|
#define MICROPY_HW_SDRAM_SIZE (64 / 8 * 1024 * 1024) // 64 Mbit
|
|
#define MICROPY_HW_SDRAM_STARTUP_TEST (1)
|
|
#define MICROPY_HEAP_START sdram_start()
|
|
#define MICROPY_HEAP_END sdram_end()
|
|
|
|
// Timing configuration for 90 Mhz (11.90ns) of SD clock frequency (180Mhz/2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TMRD (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TXSR (7)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRAS (4)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRC (7)
|
|
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRP (2)
|
|
#define MICROPY_HW_SDRAM_TIMING_TRCD (2)
|
|
#define MICROPY_HW_SDRAM_REFRESH_RATE (64) // ms
|
|
|
|
#define MICROPY_HW_SDRAM_BURST_LENGTH 1
|
|
#define MICROPY_HW_SDRAM_CAS_LATENCY 2
|
|
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM 8
|
|
#define MICROPY_HW_SDRAM_ROW_BITS_NUM 12
|
|
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH 16
|
|
#define MICROPY_HW_SDRAM_INTERN_BANKS_NUM 4
|
|
#define MICROPY_HW_SDRAM_CLOCK_PERIOD 2
|
|
#define MICROPY_HW_SDRAM_RPIPE_DELAY 0
|
|
#define MICROPY_HW_SDRAM_RBURST (1)
|
|
#define MICROPY_HW_SDRAM_WRITE_PROTECTION (0)
|
|
#define MICROPY_HW_SDRAM_AUTOREFRESH_NUM (8)
|
|
|
|
#define MICROPY_HW_FMC_SDCKE0 (pin_C3)
|
|
#define MICROPY_HW_FMC_SDNE0 (pin_H3)
|
|
#define MICROPY_HW_FMC_SDCLK (pin_G8)
|
|
#define MICROPY_HW_FMC_SDNCAS (pin_G15)
|
|
#define MICROPY_HW_FMC_SDNRAS (pin_F11)
|
|
#define MICROPY_HW_FMC_SDNWE (pin_H5)
|
|
#define MICROPY_HW_FMC_BA0 (pin_G4)
|
|
#define MICROPY_HW_FMC_BA1 (pin_G5)
|
|
#define MICROPY_HW_FMC_NBL0 (pin_E0)
|
|
#define MICROPY_HW_FMC_NBL1 (pin_E1)
|
|
#define MICROPY_HW_FMC_A0 (pin_F0)
|
|
#define MICROPY_HW_FMC_A1 (pin_F1)
|
|
#define MICROPY_HW_FMC_A2 (pin_F2)
|
|
#define MICROPY_HW_FMC_A3 (pin_F3)
|
|
#define MICROPY_HW_FMC_A4 (pin_F4)
|
|
#define MICROPY_HW_FMC_A5 (pin_F5)
|
|
#define MICROPY_HW_FMC_A6 (pin_F12)
|
|
#define MICROPY_HW_FMC_A7 (pin_F13)
|
|
#define MICROPY_HW_FMC_A8 (pin_F14)
|
|
#define MICROPY_HW_FMC_A9 (pin_F15)
|
|
#define MICROPY_HW_FMC_A10 (pin_G0)
|
|
#define MICROPY_HW_FMC_A11 (pin_G1)
|
|
#define MICROPY_HW_FMC_D0 (pin_D14)
|
|
#define MICROPY_HW_FMC_D1 (pin_D15)
|
|
#define MICROPY_HW_FMC_D2 (pin_D0)
|
|
#define MICROPY_HW_FMC_D3 (pin_D1)
|
|
#define MICROPY_HW_FMC_D4 (pin_E7)
|
|
#define MICROPY_HW_FMC_D5 (pin_E8)
|
|
#define MICROPY_HW_FMC_D6 (pin_E9)
|
|
#define MICROPY_HW_FMC_D7 (pin_E10)
|
|
#define MICROPY_HW_FMC_D8 (pin_E11)
|
|
#define MICROPY_HW_FMC_D9 (pin_E12)
|
|
#define MICROPY_HW_FMC_D10 (pin_E13)
|
|
#define MICROPY_HW_FMC_D11 (pin_E14)
|
|
#define MICROPY_HW_FMC_D12 (pin_E15)
|
|
#define MICROPY_HW_FMC_D13 (pin_D8)
|
|
#define MICROPY_HW_FMC_D14 (pin_D9)
|
|
#define MICROPY_HW_FMC_D15 (pin_D10)
|