0dbd928cee
Scenario: module1 depends on some common file from lib/, so specifies it in its SRC_MOD, and the same situation with module2, then common file from lib/ eventually ends up listed twice in $(OBJ), which leads to link errors. Make is equipped to deal with such situation easily, quoting the manual: "The value of $^ omits duplicate prerequisites, while $+ retains them and preserves their order." So, just use $^ consistently in all link targets. |
||
|---|---|---|
| .. | ||
| core | ||
| memzip_files | ||
| Makefile | ||
| README.md | ||
| add-memzip.sh | ||
| hal_ftm.c | ||
| hal_ftm.h | ||
| hal_gpio.c | ||
| help.c | ||
| import.c | ||
| lcd.c | ||
| led.c | ||
| led.h | ||
| lexerfatfs.c | ||
| lexermemzip.c | ||
| lexermemzip.h | ||
| main.c | ||
| make-pins.py | ||
| memzip.c | ||
| memzip.h | ||
| mk20dx256.ld | ||
| mk20dx256_af.csv | ||
| mk20dx256_prefix.c | ||
| modpyb.c | ||
| mpconfigport.h | ||
| pin_defs_teensy.c | ||
| pin_defs_teensy.h | ||
| qstrdefsport.h | ||
| reg.c | ||
| reg.h | ||
| servo.c | ||
| servo.h | ||
| std.h | ||
| teensy_hal.c | ||
| teensy_hal.h | ||
| teensy_pins.csv | ||
| timer.c | ||
| timer.h | ||
| uart.c | ||
| usb.c | ||
| usb.h | ||
README.md
Build Instructions for Teensy 3.1
Currently the Teensy 3.1 port of MicroPython builds under Linux and not under Windows.
The tool chain required for the build can be found at https://launchpad.net/gcc-arm-embedded.
Download the current Linux *.tar.bz2 file. Instructions regarding unpacking the file and moving it to the correct location as well as adding the extracted folders to the enviroment variable can be found at http://eliaselectronics.com/stm32f4-tutorials/setting-up-the-stm32f4-arm-development-toolchain/
In order to download the firmware image to the teensy, you'll need to use the downloader included with TeensyDuino. The following assumes that you have TeensyDuino installed and set the ARDUINO environment variable pointing to the where Arduino with TeensyDuino is installed.
cd teensy
ARDUINO=~/arduino-1.0.5 make
To upload micropython to the Teensy 3.1.
Press the Program button on the Teensy 3.1
sudo ARDUINO=~/arduino-1.0.5/ make deploy
Currently, the Python prompt is through the USB serial interface, i.e.
minicom -D /dev/ttyACM0
TIPS
Install 49-teensy.rules into /etc/udev/rules.d
If you install the 49-teensy.rules file from http://www.pjrc.com/teensy/49-teensy.rules
into your /etc/udev/rules.d folder then you won't need to use sudo:
sudo cp ~/Downloads/49-teensy.rules /etc/udev/rules.d
sudo udevadm control --reload-rules
Unplug and replug the teensy board, and then you can use: ARDUINO=~/arduino-1.0.5/ make deploy
Create a GNUmakefile to hold your ARDUINO setting.
Create a file call GNUmakefile (note the lowercase m) in the teensy folder with the following contents:
$(info Executing GNUmakefile)
ARDUINO=${HOME}/arduino-1.0.5
$(info ARDUINO=${ARDUINO})
include Makefile
GNUmakefile is not checked into the source code control system, so it will retain your settings when updating your source tree. You can also add additional Makefile customizations this way.