5ca56aaf16
- Move the qspi_xxxx_flash_config.c files to hal. It turned out that they are less board than flash type specific. - Change to a common flexspi_flash_config.h header file.
264 lines
12 KiB
C
264 lines
12 KiB
C
/*
|
|
* Copyright 2018 NXP
|
|
* All rights reserved.
|
|
*
|
|
* SPDX-License-Identifier: BSD-3-Clause
|
|
*/
|
|
|
|
#ifndef __FLEXSPI_FLASH_CONFIG__
|
|
#define __FLEXSPI_FLASH_CONFIG__
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
#include "fsl_flexspi.h"
|
|
|
|
/*! @name Driver version */
|
|
/*@{*/
|
|
/*! @brief XIP_BOARD driver version 2.0.0. */
|
|
#define FSL_XIP_BOARD_DRIVER_VERSION (MAKE_VERSION(2, 0, 0))
|
|
/*@}*/
|
|
|
|
/* FLEXSPI memory config block related defintions */
|
|
#define FLEXSPI_CFG_BLK_TAG (0x42464346UL) // ascii "FCFB" Big Endian
|
|
#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0
|
|
#define FLEXSPI_CFG_BLK_SIZE (512)
|
|
|
|
/* FLEXSPI Feature related definitions */
|
|
#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1
|
|
|
|
/* Lookup table related defintions */
|
|
#define CMD_INDEX_READ 0
|
|
#define CMD_INDEX_READSTATUS 1
|
|
#define CMD_INDEX_WRITEENABLE 2
|
|
#define CMD_INDEX_WRITE 4
|
|
|
|
#define CMD_LUT_SEQ_IDX_READ 0
|
|
#define CMD_LUT_SEQ_IDX_READSTATUS 1
|
|
#define CMD_LUT_SEQ_IDX_WRITEENABLE 3
|
|
#define CMD_LUT_SEQ_IDX_WRITE 9
|
|
|
|
#define CMD_SDR 0x01
|
|
#define CMD_DDR 0x21
|
|
#define RADDR_SDR 0x02
|
|
#define RADDR_DDR 0x22
|
|
#define CADDR_SDR 0x03
|
|
#define CADDR_DDR 0x23
|
|
#define MODE1_SDR 0x04
|
|
#define MODE1_DDR 0x24
|
|
#define MODE2_SDR 0x05
|
|
#define MODE2_DDR 0x25
|
|
#define MODE4_SDR 0x06
|
|
#define MODE4_DDR 0x26
|
|
#define MODE8_SDR 0x07
|
|
#define MODE8_DDR 0x27
|
|
#define WRITE_SDR 0x08
|
|
#define WRITE_DDR 0x28
|
|
#define READ_SDR 0x09
|
|
#define READ_DDR 0x29
|
|
#define LEARN_SDR 0x0A
|
|
#define LEARN_DDR 0x2A
|
|
#define DATSZ_SDR 0x0B
|
|
#define DATSZ_DDR 0x2B
|
|
#define DUMMY_SDR 0x0C
|
|
#define DUMMY_DDR 0x2C
|
|
#define DUMMY_RWDS_SDR 0x0D
|
|
#define DUMMY_RWDS_DDR 0x2D
|
|
#define JMP_ON_CS 0x1F
|
|
#define STOP 0
|
|
|
|
#define FLEXSPI_1PAD 0
|
|
#define FLEXSPI_2PAD 1
|
|
#define FLEXSPI_4PAD 2
|
|
#define FLEXSPI_8PAD 3
|
|
|
|
#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1) \
|
|
(FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \
|
|
FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1))
|
|
|
|
// !@brief Definitions for FlexSPI Serial Clock Frequency
|
|
typedef enum _FlexSpiSerialClockFreq
|
|
{
|
|
kFlexSpiSerialClk_30MHz = 1,
|
|
kFlexSpiSerialClk_50MHz = 2,
|
|
kFlexSpiSerialClk_60MHz = 3,
|
|
kFlexSpiSerialClk_75MHz = 4,
|
|
kFlexSpiSerialClk_80MHz = 5,
|
|
kFlexSpiSerialClk_100MHz = 6,
|
|
kFlexSpiSerialClk_133MHz = 7,
|
|
kFlexSpiSerialClk_166MHz = 8,
|
|
} flexspi_serial_clk_freq_t;
|
|
|
|
// !@brief FlexSPI clock configuration type
|
|
enum
|
|
{
|
|
kFlexSpiClk_SDR, // !< Clock configure for SDR mode
|
|
kFlexSpiClk_DDR, // !< Clock configurat for DDR mode
|
|
};
|
|
|
|
// !@brief FlexSPI Read Sample Clock Source definition
|
|
typedef enum _FlashReadSampleClkSource
|
|
{
|
|
kFlexSPIReadSampleClk_LoopbackInternally = 0,
|
|
kFlexSPIReadSampleClk_LoopbackFromDqsPad = 1,
|
|
kFlexSPIReadSampleClk_LoopbackFromSckPad = 2,
|
|
kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3,
|
|
} flexspi_read_sample_clk_t;
|
|
|
|
// !@brief Misc feature bit definitions
|
|
enum
|
|
{
|
|
kFlexSpiMiscOffset_DiffClkEnable = 0, // !< Bit for Differential clock enable
|
|
kFlexSpiMiscOffset_Ck2Enable = 1, // !< Bit for CK2 enable
|
|
kFlexSpiMiscOffset_ParallelEnable = 2, // !< Bit for Parallel mode enable
|
|
kFlexSpiMiscOffset_WordAddressableEnable = 3, // !< Bit for Word Addressable enable
|
|
kFlexSpiMiscOffset_SafeConfigFreqEnable = 4, // !< Bit for Safe Configuration Frequency enable
|
|
kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, // !< Bit for Pad setting override enable
|
|
kFlexSpiMiscOffset_DdrModeEnable = 6, // !< Bit for DDR clock confiuration indication.
|
|
};
|
|
|
|
// !@brief Flash Type Definition
|
|
enum
|
|
{
|
|
kFlexSpiDeviceType_SerialNOR = 1, // !< Flash devices are Serial NOR
|
|
kFlexSpiDeviceType_SerialNAND = 2, // !< Flash devices are Serial NAND
|
|
kFlexSpiDeviceType_SerialRAM = 3, // !< Flash devices are Serial RAM/HyperFLASH
|
|
kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, // !< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND
|
|
kFlexSpiDeviceType_MCP_NOR_RAM = 0x13, // !< Flash deivce is MCP device, A1 is Serial NOR, A2 is Serial RAMs
|
|
};
|
|
|
|
// !@brief Flash Pad Definitions
|
|
enum
|
|
{
|
|
kSerialFlash_1Pad = 1,
|
|
kSerialFlash_2Pads = 2,
|
|
kSerialFlash_4Pads = 4,
|
|
kSerialFlash_8Pads = 8,
|
|
};
|
|
|
|
// !@brief FlexSPI LUT Sequence structure
|
|
typedef struct _lut_sequence
|
|
{
|
|
uint8_t seqNum; // !< Sequence Number, valid number: 1-16
|
|
uint8_t seqId; // !< Sequence Index, valid number: 0-15
|
|
uint16_t reserved;
|
|
} flexspi_lut_seq_t;
|
|
|
|
// !@brief Flash Configuration Command Type
|
|
enum
|
|
{
|
|
kDeviceConfigCmdType_Generic, // !< Generic command, for example: configure dummy cycles, drive strength, etc
|
|
kDeviceConfigCmdType_QuadEnable, // !< Quad Enable command
|
|
kDeviceConfigCmdType_Spi2Xpi, // !< Switch from SPI to DPI/QPI/OPI mode
|
|
kDeviceConfigCmdType_Xpi2Spi, // !< Switch from DPI/QPI/OPI to SPI mode
|
|
kDeviceConfigCmdType_Spi2NoCmd, // !< Switch to 0-4-4/0-8-8 mode
|
|
kDeviceConfigCmdType_Reset, // !< Reset device command
|
|
};
|
|
|
|
// !@brief FlexSPI Memory Configuration Block
|
|
typedef struct _FlexSPIConfig
|
|
{
|
|
uint32_t tag; // !< [0x000-0x003] Tag, fixed value 0x42464346UL
|
|
uint32_t version; // !< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
|
|
uint32_t reserved0; // !< [0x008-0x00b] Reserved for future use
|
|
uint8_t readSampleClkSrc; // !< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
|
|
uint8_t csHoldTime; // !< [0x00d-0x00d] CS hold time, default value: 3
|
|
uint8_t csSetupTime; // !< [0x00e-0x00e] CS setup time, default value: 3
|
|
uint8_t columnAddressWidth; // !< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For
|
|
// ! Serial NAND, need to refer to datasheet
|
|
uint8_t deviceModeCfgEnable; // !< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
|
|
uint8_t deviceModeType; // !< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch,
|
|
// ! Generic configuration, etc.
|
|
uint16_t waitTimeCfgCommands; // !< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for
|
|
// ! DPI/QPI/OPI switch or reset command
|
|
flexspi_lut_seq_t deviceModeSeq; // !< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt
|
|
// ! sequence number, [31:16] Reserved
|
|
uint32_t deviceModeArg; // !< [0x018-0x01b] Argument/Parameter for device configuration
|
|
uint8_t configCmdEnable; // !< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
|
|
uint8_t configModeType[3]; // !< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
|
|
flexspi_lut_seq_t
|
|
configCmdSeqs[3]; // !< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
|
|
uint32_t reserved1; // !< [0x02c-0x02f] Reserved for future use
|
|
uint32_t configCmdArgs[3]; // !< [0x030-0x03b] Arguments/Parameters for device Configuration commands
|
|
uint32_t reserved2; // !< [0x03c-0x03f] Reserved for future use
|
|
uint32_t controllerMiscOption; // !< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more
|
|
// ! details
|
|
uint8_t deviceType; // !< [0x044-0x044] Device Type: See Flash Type Definition for more details
|
|
uint8_t sflashPadType; // !< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
|
|
uint8_t serialClkFreq; // !< [0x046-0x046] Serial Flash Frequencey, device specific definitions, See System Boot
|
|
// ! Chapter for more details
|
|
uint8_t lutCustomSeqEnable; // !< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot
|
|
// ! be done using 1 LUT sequence, currently, only applicable to HyperFLASH
|
|
uint32_t reserved3[2]; // !< [0x048-0x04f] Reserved for future use
|
|
uint32_t sflashA1Size; // !< [0x050-0x053] Size of Flash connected to A1
|
|
uint32_t sflashA2Size; // !< [0x054-0x057] Size of Flash connected to A2
|
|
uint32_t sflashB1Size; // !< [0x058-0x05b] Size of Flash connected to B1
|
|
uint32_t sflashB2Size; // !< [0x05c-0x05f] Size of Flash connected to B2
|
|
uint32_t csPadSettingOverride; // !< [0x060-0x063] CS pad setting override value
|
|
uint32_t sclkPadSettingOverride; // !< [0x064-0x067] SCK pad setting override value
|
|
uint32_t dataPadSettingOverride; // !< [0x068-0x06b] data pad setting override value
|
|
uint32_t dqsPadSettingOverride; // !< [0x06c-0x06f] DQS pad setting override value
|
|
uint32_t timeoutInMs; // !< [0x070-0x073] Timeout threshold for read status command
|
|
uint32_t commandInterval; // !< [0x074-0x077] CS deselect interval between two commands
|
|
uint16_t dataValidTime[2]; // !< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns
|
|
uint16_t busyOffset; // !< [0x07c-0x07d] Busy offset, valid value: 0-31
|
|
uint16_t busyBitPolarity; // !< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 -
|
|
// ! busy flag is 0 when flash device is busy
|
|
uint32_t lookupTable[64]; // !< [0x080-0x17f] Lookup table holds Flash command sequences
|
|
flexspi_lut_seq_t lutCustomSeq[12]; // !< [0x180-0x1af] Customizable LUT Sequences
|
|
uint32_t reserved4[4]; // !< [0x1b0-0x1bf] Reserved for future use
|
|
} flexspi_mem_config_t;
|
|
|
|
/* */
|
|
#define NOR_CMD_LUT_SEQ_IDX_READ_NORMAL 0
|
|
#define NOR_CMD_LUT_SEQ_IDX_READSTATUSREG 1
|
|
#define NOR_CMD_LUT_SEQ_IDX_READ_FAST_QUAD 2
|
|
#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE 3
|
|
#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI 4
|
|
#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5
|
|
#define NOR_CMD_LUT_SEQ_IDX_WRITESTATUSREG 6
|
|
#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM_QUAD 7
|
|
#define NOR_CMD_LUT_SEQ_IDX_READID 8
|
|
#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM 9
|
|
#define NOR_CMD_LUT_SEQ_IDX_ENTERQPI 10
|
|
#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11
|
|
#define NOR_CMD_LUT_SEQ_IDX_EXITQPI 12
|
|
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_READDATA 0
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_WRITEDATA 1
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_READSTATUS 2
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_WRITEENABLE 4
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_ERASESECTOR 6
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_PAGEPROGRAM 10
|
|
#define HYPERFLASH_CMD_LUT_SEQ_IDX_ERASECHIP 12
|
|
|
|
/*
|
|
* Serial NOR configuration block
|
|
*/
|
|
typedef struct _flexspi_nor_config
|
|
{
|
|
flexspi_mem_config_t memConfig; // !< Common memory configuration info via FlexSPI
|
|
uint32_t pageSize; // !< Page size of Serial NOR
|
|
uint32_t sectorSize; // !< Sector size of Serial NOR
|
|
uint8_t ipcmdSerialClkFreq; // !< Clock frequency for IP command
|
|
uint8_t isUniformBlockSize; // !< Sector/Block size is the same
|
|
uint8_t reserved0[2]; // !< Reserved for future use
|
|
uint8_t serialNorType; // !< Serial NOR Flash type: 0/1/2/3
|
|
uint8_t needExitNoCmdMode; // !< Need to exit NoCmd mode before other IP command
|
|
uint8_t halfClkForNonReadCmd; // !< Half the Serial Clock for non-read command: true/false
|
|
uint8_t needRestoreNoCmdMode; // !< Need to Restore NoCmd mode after IP commmand execution
|
|
uint32_t blockSize; // !< Block size
|
|
uint32_t reserve2[11]; // !< Reserved for future use
|
|
} flexspi_nor_config_t;
|
|
|
|
#define FLASH_BUSY_STATUS_POL 0
|
|
#define FLASH_BUSY_STATUS_OFFSET 0
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
#endif /* __FLEXSPI_FLASH_CONFIG__ */
|