circuitpython/ports/stm32/boards/B_L072Z_LRWAN1/mpconfigboard.h

74 lines
2.7 KiB
C

/* This file is part of the MicroPython project, http://micropython.org/
* MIT License; Copyright (c) 2019 Damien P. George
*/
#define MICROPY_HW_BOARD_NAME "B-L072Z-LRWAN1"
#define MICROPY_HW_MCU_NAME "STM32L072CZ"
#define MICROPY_EMIT_THUMB (0)
#define MICROPY_EMIT_INLINE_THUMB (0)
#define MICROPY_OPT_COMPUTED_GOTO (0)
#define MICROPY_PY_BUILTINS_COMPLEX (0)
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
#define MICROPY_PY_MATH (0)
#define MICROPY_PY_IO_FILEIO (0)
#define MICROPY_PY_FRAMEBUF (0)
#define MICROPY_PY_USOCKET (0)
#define MICROPY_PY_NETWORK (0)
#define MICROPY_PY_ONEWIRE (0)
#define MICROPY_PY_STM (0)
#define MICROPY_PY_PYB_LEGACY (0)
#define MICROPY_PY_UHEAPQ (0)
#define MICROPY_PY_UTIMEQ (0)
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_ADC (0)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_HAS_SWITCH (1)
// UART config
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
// USART2 is connected to the ST-LINK USB VCP
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C buses
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
// SPI buses
#define MICROPY_HW_SPI1_NSS (pin_A15)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// USER B1 has a pull-up and is active low
#define MICROPY_HW_USRSW_PIN (pin_B2)
#define MICROPY_HW_USRSW_PULL (0)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// 4 user LEDs
#define MICROPY_HW_LED1 (pin_B5) // Green
#define MICROPY_HW_LED2 (pin_A5) // Green (next to power LED)
#define MICROPY_HW_LED3 (pin_B6) // Blue
#define MICROPY_HW_LED4 (pin_B7) // Red
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config (need to bridge SB15/SB16)
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_MSC (0)
#define MICROPY_HW_USB_HID (0)
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (256)
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (256)