djsundog
/
circuitpython
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
circuitpython/ports/cc3200/hal/inc/hw_ocp_shared.h

3446 lines
215 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

//*****************************************************************************
//
// Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
//
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//
// Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the
// distribution.
//
// Neither the name of Texas Instruments Incorporated nor the names of
// its contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//*****************************************************************************
#ifndef __HW_OCP_SHARED_H__
#define __HW_OCP_SHARED_H__
//*****************************************************************************
//
// The following are defines for the OCP_SHARED register offsets.
//
//*****************************************************************************
#define OCP_SHARED_O_SEMAPHORE1 0x00000000
#define OCP_SHARED_O_SEMAPHORE2 0x00000004
#define OCP_SHARED_O_SEMAPHORE3 0x00000008
#define OCP_SHARED_O_SEMAPHORE4 0x0000000C
#define OCP_SHARED_O_SEMAPHORE5 0x00000010
#define OCP_SHARED_O_SEMAPHORE6 0x00000014
#define OCP_SHARED_O_SEMAPHORE7 0x00000018
#define OCP_SHARED_O_SEMAPHORE8 0x0000001C
#define OCP_SHARED_O_SEMAPHORE9 0x00000020
#define OCP_SHARED_O_SEMAPHORE10 \
0x00000024
#define OCP_SHARED_O_SEMAPHORE11 \
0x00000028
#define OCP_SHARED_O_SEMAPHORE12 \
0x0000002C
#define OCP_SHARED_O_IC_LOCKER_ID \
0x00000030
#define OCP_SHARED_O_MCU_SEMAPHORE_PEND \
0x00000034
#define OCP_SHARED_O_WL_SEMAPHORE_PEND \
0x00000038
#define OCP_SHARED_O_PLATFORM_DETECTION_RD_ONLY \
0x0000003C
#define OCP_SHARED_O_SEMAPHORES_STATUS_RD_ONLY \
0x00000040
#define OCP_SHARED_O_CC3XX_CONFIG_CTRL \
0x00000044
#define OCP_SHARED_O_CC3XX_SHARED_MEM_SEL_LSB \
0x00000048
#define OCP_SHARED_O_CC3XX_SHARED_MEM_SEL_MSB \
0x0000004C
#define OCP_SHARED_O_WLAN_ELP_WAKE_EN \
0x00000050
#define OCP_SHARED_O_DEVINIT_ROM_START_ADDR \
0x00000054
#define OCP_SHARED_O_DEVINIT_ROM_END_ADDR \
0x00000058
#define OCP_SHARED_O_SSBD_SEED 0x0000005C
#define OCP_SHARED_O_SSBD_CHK 0x00000060
#define OCP_SHARED_O_SSBD_POLY_SEL \
0x00000064
#define OCP_SHARED_O_SPARE_REG_0 \
0x00000068
#define OCP_SHARED_O_SPARE_REG_1 \
0x0000006C
#define OCP_SHARED_O_SPARE_REG_2 \
0x00000070
#define OCP_SHARED_O_SPARE_REG_3 \
0x00000074
#define OCP_SHARED_O_GPIO_PAD_CONFIG_0 \
0x000000A0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_1 \
0x000000A4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_2 \
0x000000A8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_3 \
0x000000AC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_4 \
0x000000B0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_5 \
0x000000B4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_6 \
0x000000B8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_7 \
0x000000BC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_8 \
0x000000C0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_9 \
0x000000C4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_10 \
0x000000C8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_11 \
0x000000CC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_12 \
0x000000D0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_13 \
0x000000D4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_14 \
0x000000D8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_15 \
0x000000DC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_16 \
0x000000E0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_17 \
0x000000E4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_18 \
0x000000E8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_19 \
0x000000EC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_20 \
0x000000F0
#define OCP_SHARED_O_GPIO_PAD_CONFIG_21 \
0x000000F4
#define OCP_SHARED_O_GPIO_PAD_CONFIG_22 \
0x000000F8
#define OCP_SHARED_O_GPIO_PAD_CONFIG_23 \
0x000000FC
#define OCP_SHARED_O_GPIO_PAD_CONFIG_24 \
0x00000100
#define OCP_SHARED_O_GPIO_PAD_CONFIG_25 \
0x00000104
#define OCP_SHARED_O_GPIO_PAD_CONFIG_26 \
0x00000108
#define OCP_SHARED_O_GPIO_PAD_CONFIG_27 \
0x0000010C
#define OCP_SHARED_O_GPIO_PAD_CONFIG_28 \
0x00000110
#define OCP_SHARED_O_GPIO_PAD_CONFIG_29 \
0x00000114
#define OCP_SHARED_O_GPIO_PAD_CONFIG_30 \
0x00000118
#define OCP_SHARED_O_GPIO_PAD_CONFIG_31 \
0x0000011C
#define OCP_SHARED_O_GPIO_PAD_CONFIG_32 \
0x00000120
#define OCP_SHARED_O_GPIO_PAD_CONFIG_33 \
0x00000124
#define OCP_SHARED_O_GPIO_PAD_CONFIG_34 \
0x00000128
#define OCP_SHARED_O_GPIO_PAD_CONFIG_35 \
0x0000012C
#define OCP_SHARED_O_GPIO_PAD_CONFIG_36 \
0x00000130
#define OCP_SHARED_O_GPIO_PAD_CONFIG_37 \
0x00000134
#define OCP_SHARED_O_GPIO_PAD_CONFIG_38 \
0x00000138
#define OCP_SHARED_O_GPIO_PAD_CONFIG_39 \
0x0000013C
#define OCP_SHARED_O_GPIO_PAD_CONFIG_40 \
0x00000140
#define OCP_SHARED_O_GPIO_PAD_CMN_CONFIG \
0x00000144 // This register provide control to
// GPIO_CC3XXV1 IO PAD. Common
// control signals to all bottom Die
// IO's are controlled via this.
#define OCP_SHARED_O_D2D_DEV_PAD_CMN_CONFIG \
0x00000148
#define OCP_SHARED_O_D2D_TOSTACK_PAD_CONF \
0x0000014C
#define OCP_SHARED_O_D2D_MISC_PAD_CONF \
0x00000150
#define OCP_SHARED_O_SOP_CONF_OVERRIDE \
0x00000154
#define OCP_SHARED_O_CC3XX_DEBUGSS_STATUS \
0x00000158
#define OCP_SHARED_O_CC3XX_DEBUGMUX_SEL \
0x0000015C
#define OCP_SHARED_O_ALT_PC_VAL_NW \
0x00000160
#define OCP_SHARED_O_ALT_PC_VAL_APPS \
0x00000164
#define OCP_SHARED_O_SPARE_REG_4 \
0x00000168
#define OCP_SHARED_O_SPARE_REG_5 \
0x0000016C
#define OCP_SHARED_O_SH_SPI_CS_MASK \
0x00000170
#define OCP_SHARED_O_CC3XX_DEVICE_TYPE \
0x00000174
#define OCP_SHARED_O_MEM_TOPMUXCTRL_IFORCE \
0x00000178
#define OCP_SHARED_O_CC3XX_DEV_PACKAGE_DETECT \
0x0000017C
#define OCP_SHARED_O_AUTONMS_SPICLK_SEL \
0x00000180
#define OCP_SHARED_O_CC3XX_DEV_PADCONF \
0x00000184
#define OCP_SHARED_O_SPARE_REG_8 \
0x00000188
#define OCP_SHARED_O_SPARE_REG_6 \
0x0000018C
#define OCP_SHARED_O_SPARE_REG_7 \
0x00000190
#define OCP_SHARED_O_APPS_WLAN_ORBIT \
0x00000194
#define OCP_SHARED_O_APPS_WLAN_SCRATCH_PAD \
0x00000198
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE1 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE1_MEM_SEMAPHORE1_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE1_MEM_SEMAPHORE1_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE2 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE2_MEM_SEMAPHORE2_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE2_MEM_SEMAPHORE2_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE3 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE3_MEM_SEMAPHORE3_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE3_MEM_SEMAPHORE3_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE4 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE4_MEM_SEMAPHORE4_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE4_MEM_SEMAPHORE4_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE5 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE5_MEM_SEMAPHORE5_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE5_MEM_SEMAPHORE5_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE6 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE6_MEM_SEMAPHORE6_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE6_MEM_SEMAPHORE6_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE7 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE7_MEM_SEMAPHORE7_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE7_MEM_SEMAPHORE7_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE8 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE8_MEM_SEMAPHORE8_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE8_MEM_SEMAPHORE8_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE9 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE9_MEM_SEMAPHORE9_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE9_MEM_SEMAPHORE9_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE10 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE10_MEM_SEMAPHORE10_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE10_MEM_SEMAPHORE10_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE11 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE11_MEM_SEMAPHORE11_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE11_MEM_SEMAPHORE11_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORE12 register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORE12_MEM_SEMAPHORE12_M \
0x00000003 // General Purpose Semaphore for SW
// Usage. If any of the 2 bits of a
// given register is set to 1, it
// means that the semaphore is
// locked by one of the masters.
// Each bit represents a master IP
// as follows: {WLAN,NWP}. The JTAG
// cannot capture the semaphore but
// it can release it. As a master IP
// reads the semaphore, it will be
// caputed and the masters
// correlating bit will be set to 1
// (set upon read). As any IP writes
// to this address (independent of
// the written data) the semaphore
// will be set to 2'b00.
#define OCP_SHARED_SEMAPHORE12_MEM_SEMAPHORE12_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_IC_LOCKER_ID register.
//
//******************************************************************************
#define OCP_SHARED_IC_LOCKER_ID_MEM_IC_LOCKER_ID_M \
0x00000007 // This register is used for
// allowing only one master OCP to
// perform write transactions to the
// OCP slaves. Each bit represents
// an IP in the following format: {
// JTAG,WLAN, NWP mcu}. As any of
// the bits is set to one, the
// correlating IP is preventing the
// other IP's from performing write
// transactions to the slaves. As
// the Inter Connect is locked, the
// only the locking IP can write to
// the register and by that
// releasing the lock. 3'b000 => IC
// is not locked. 3'b001 => IC is
// locked by NWP mcu. 3'b010 => IC
// is locked by WLAN. 3'b100 => IC
// is locked by JTAG.
#define OCP_SHARED_IC_LOCKER_ID_MEM_IC_LOCKER_ID_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_MCU_SEMAPHORE_PEND register.
//
//******************************************************************************
#define OCP_SHARED_MCU_SEMAPHORE_PEND_MEM_MCU_SEMAPHORE_PEND_M \
0x0000FFFF // This register specifies the
// semaphore for which the NWP mcu
// is waiting to be released. It is
// set to the serial number of a
// given locked semaphore after it
// was read by the NWP mcu. Only
// [11:0] is used.
#define OCP_SHARED_MCU_SEMAPHORE_PEND_MEM_MCU_SEMAPHORE_PEND_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_WL_SEMAPHORE_PEND register.
//
//******************************************************************************
#define OCP_SHARED_WL_SEMAPHORE_PEND_MEM_WL_SEMAPHORE_PEND_M \
0x0000FFFF // This register specifies the
// semaphore for which the WLAN is
// waiting to be released. It is set
// to the serial number of a given
// locked semaphore after it was
// read by the WLAN. Only [11:0] is
// used.
#define OCP_SHARED_WL_SEMAPHORE_PEND_MEM_WL_SEMAPHORE_PEND_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_PLATFORM_DETECTION_RD_ONLY register.
//
//******************************************************************************
#define OCP_SHARED_PLATFORM_DETECTION_RD_ONLY_PLATFORM_DETECTION_M \
0x0000FFFF // This information serves the IPs
// for knowing in which platform are
// they integrated at: 0 = CC31XX.
#define OCP_SHARED_PLATFORM_DETECTION_RD_ONLY_PLATFORM_DETECTION_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SEMAPHORES_STATUS_RD_ONLY register.
//
//******************************************************************************
#define OCP_SHARED_SEMAPHORES_STATUS_RD_ONLY_SEMAPHORES_STATUS_M \
0x00000FFF // Captured/released semaphores
// status for the 12 semaphores.
// Each bit of the 12 bits
// represents a semaphore. 0 =>
// Semaphore Free. 1 => Semaphore
// Captured.
#define OCP_SHARED_SEMAPHORES_STATUS_RD_ONLY_SEMAPHORES_STATUS_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_CONFIG_CTRL register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_CONFIG_CTRL_MEM_IC_TO_EN \
0x00000010 // This bit is used to enable
// timeout mechanism for top_ocp_ic
// (for debug puropse). When 1 value
// , in case any ocp slave doesn't
// give sresponse within 16 cylcles
// top_ic will give error response
// itself to avoid bus hange.
#define OCP_SHARED_CC3XX_CONFIG_CTRL_MEM_ALT_PC_EN_APPS \
0x00000008 // 1 bit should be accessible only
// in devinit. This will enable 0x4
// hack for apps processor
#define OCP_SHARED_CC3XX_CONFIG_CTRL_MEM_ALT_PC_EN_NW \
0x00000004 // 1 bit, should be accessible only
// in devinit. This will enable 0x4
// hack for nw processor
#define OCP_SHARED_CC3XX_CONFIG_CTRL_MEM_EXTEND_NW_ROM \
0x00000002 // When set NW can take over apps
// rom and flash via IDCODE bus.
// Apps will able to access this
// register only during devinit and
// reset value should be 0.
#define OCP_SHARED_CC3XX_CONFIG_CTRL_MEM_WLAN_HOST_INTF_SEL \
0x00000001 // When this bit is set to 0 WPSI
// host interface wil be selected,
// when this bit is set to 1 , WLAN
// host async bridge will be
// selected.
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_SHARED_MEM_SEL_LSB register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_SHARED_MEM_SEL_LSB_MEM_SHARED_MEM_SEL_LSB_M \
0x3FFFFFFF // This register provides memss RAM
// column configuration for column 0
// to 9. 3 bits are allocated per
// column. This register is required
// to be configured before starting
// RAM access. Changing register
// setting while code is running
// will result into unpredictable
// memory behaviour. Register is
// supported to configured ones
// after core is booted up. 3 bit
// encoding per column is as
// follows: when 000 : WLAN, 001:
// NWP, 010: APPS, 011: PHY, 100:
// OCLA column 0 select: bit [2:0]
// :when 000 -> WLAN,001 -> NWP,010
// -> APPS, 011 -> PHY, 100 -> OCLA
// column 1 select: bit [5:3]
// :column 2 select: bit [8 : 6]:
// column 3 select : bit [11: 9]
// column 4 select : bit [14:12]
// column 5 select : bit [17:15]
// column 6 select : bit [20:18]
// column 7 select : bit [23:21]
// column 8 select : bit [26:24]
// column 9 select : bit [29:27]
// column 10 select
#define OCP_SHARED_CC3XX_SHARED_MEM_SEL_LSB_MEM_SHARED_MEM_SEL_LSB_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_SHARED_MEM_SEL_MSB register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_SHARED_MEM_SEL_MSB_MEM_SHARED_MEM_SEL_MSB_M \
0x00000FFF // This register provides memss RAM
// column configuration for column
// 10 to 15. 3 bits are allocated
// per column. This register is
// required to be configured before
// starting RAM access. Changing
// register setting while code is
// running will result into
// unpredictable memory behaviour.
// Register is supported to
// configured ones after core is
// booted up. 3 bit encoding per
// column is as follows: when 000 :
// WLAN, 001: NWP, 010: APPS, 011:
// PHY, 100: OCLA column 11 select :
// bit [2:0] column 12 select : bit
// [5:3] column 13 select : bit [8 :
// 6] column 14 select :
#define OCP_SHARED_CC3XX_SHARED_MEM_SEL_MSB_MEM_SHARED_MEM_SEL_MSB_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_WLAN_ELP_WAKE_EN register.
//
//******************************************************************************
#define OCP_SHARED_WLAN_ELP_WAKE_EN_MEM_WLAN_ELP_WAKE_EN \
0x00000001 // when '1' : signal will enabled
// ELP power doamin when '0': ELP is
// not powered up.
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_DEVINIT_ROM_START_ADDR register.
//
//******************************************************************************
#define OCP_SHARED_DEVINIT_ROM_START_ADDR_MEM_DEVINIT_ROM_START_ADDR_M \
0xFFFFFFFF // 32 bit, Writable only during
// devinit, and whole 32 bit should
// be output of the config register
// module. This register is not used
// , similar register availble in
// GPRCM space.
#define OCP_SHARED_DEVINIT_ROM_START_ADDR_MEM_DEVINIT_ROM_START_ADDR_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_DEVINIT_ROM_END_ADDR register.
//
//******************************************************************************
#define OCP_SHARED_DEVINIT_ROM_END_ADDR_MEM_DEVINIT_ROM_END_ADDR_M \
0xFFFFFFFF // 32 bit, Writable only during
// devinit, and whole 32 bit should
// be output of the config register
// module.
#define OCP_SHARED_DEVINIT_ROM_END_ADDR_MEM_DEVINIT_ROM_END_ADDR_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SSBD_SEED register.
//
//******************************************************************************
#define OCP_SHARED_SSBD_SEED_MEM_SSBD_SEED_M \
0xFFFFFFFF // 32 bit, Writable only during
// devinit, and whole 32 bit should
// be output of the config register
// module.
#define OCP_SHARED_SSBD_SEED_MEM_SSBD_SEED_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SSBD_CHK register.
//
//******************************************************************************
#define OCP_SHARED_SSBD_CHK_MEM_SSBD_CHK_M \
0xFFFFFFFF // 32 bit, Writable only during
// devinit, and whole 32 bit should
// be output of the config register
// module.
#define OCP_SHARED_SSBD_CHK_MEM_SSBD_CHK_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SSBD_POLY_SEL register.
//
//******************************************************************************
#define OCP_SHARED_SSBD_POLY_SEL_MEM_SSBD_POLY_SEL_M \
0x00000003 // 2 bit, Writable only during
// devinit, and whole 2 bit should
// be output of the config register
// module.
#define OCP_SHARED_SSBD_POLY_SEL_MEM_SSBD_POLY_SEL_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_0 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_0_MEM_SPARE_REG_0_M \
0xFFFFFFFF // Devinit code should look for
// whether corresponding fuse is
// blown and if blown write to the
// 11th bit of this register to
// disable flshtst interface
#define OCP_SHARED_SPARE_REG_0_MEM_SPARE_REG_0_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_1 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_1_MEM_SPARE_REG_1_M \
0xFFFFFFFF // NWP Software register
#define OCP_SHARED_SPARE_REG_1_MEM_SPARE_REG_1_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_2 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_2_MEM_SPARE_REG_2_M \
0xFFFFFFFF // NWP Software register
#define OCP_SHARED_SPARE_REG_2_MEM_SPARE_REG_2_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_3 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_3_MEM_SPARE_REG_3_M \
0xFFFFFFFF // APPS Software register
#define OCP_SHARED_SPARE_REG_3_MEM_SPARE_REG_3_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_0 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_0_MEM_GPIO_PAD_CONFIG_0_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." "For example in
// case of I2C Value gets latched at
// rising edge of RET33.""" """ 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_0_MEM_GPIO_PAD_CONFIG_0_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_1 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_1_MEM_GPIO_PAD_CONFIG_1_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_1_MEM_GPIO_PAD_CONFIG_1_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_2 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_2_MEM_GPIO_PAD_CONFIG_2_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_2_MEM_GPIO_PAD_CONFIG_2_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_3 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_3_MEM_GPIO_PAD_CONFIG_3_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_3_MEM_GPIO_PAD_CONFIG_3_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_4 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_4_MEM_GPIO_PAD_CONFIG_4_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_4_MEM_GPIO_PAD_CONFIG_4_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_5 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_5_MEM_GPIO_PAD_CONFIG_5_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_5_MEM_GPIO_PAD_CONFIG_5_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_6 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_6_MEM_GPIO_PAD_CONFIG_6_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_6_MEM_GPIO_PAD_CONFIG_6_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_7 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_7_MEM_GPIO_PAD_CONFIG_7_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_7_MEM_GPIO_PAD_CONFIG_7_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_8 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_8_MEM_GPIO_PAD_CONFIG_8_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_8_MEM_GPIO_PAD_CONFIG_8_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_9 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_9_MEM_GPIO_PAD_CONFIG_9_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_9_MEM_GPIO_PAD_CONFIG_9_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_10 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_10_MEM_GPIO_PAD_CONFIG_10_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_10_MEM_GPIO_PAD_CONFIG_10_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_11 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_11_MEM_GPIO_PAD_CONFIG_11_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_11_MEM_GPIO_PAD_CONFIG_11_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_12 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_12_MEM_GPIO_PAD_CONFIG_12_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_12_MEM_GPIO_PAD_CONFIG_12_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_13 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_13_MEM_GPIO_PAD_CONFIG_13_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_13_MEM_GPIO_PAD_CONFIG_13_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_14 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_14_MEM_GPIO_PAD_CONFIG_14_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_14_MEM_GPIO_PAD_CONFIG_14_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_15 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_15_MEM_GPIO_PAD_CONFIG_15_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_15_MEM_GPIO_PAD_CONFIG_15_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_16 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_16_MEM_GPIO_PAD_CONFIG_16_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_16_MEM_GPIO_PAD_CONFIG_16_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_17 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_17_MEM_GPIO_PAD_CONFIG_17_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_17_MEM_GPIO_PAD_CONFIG_17_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_18 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_18_MEM_GPIO_PAD_CONFIG_18_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_18_MEM_GPIO_PAD_CONFIG_18_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_19 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_19_MEM_GPIO_PAD_CONFIG_19_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_19_MEM_GPIO_PAD_CONFIG_19_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_20 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_20_MEM_GPIO_PAD_CONFIG_20_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_20_MEM_GPIO_PAD_CONFIG_20_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_21 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_21_MEM_GPIO_PAD_CONFIG_21_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_21_MEM_GPIO_PAD_CONFIG_21_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_22 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_22_MEM_GPIO_PAD_CONFIG_22_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_22_MEM_GPIO_PAD_CONFIG_22_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_23 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_23_MEM_GPIO_PAD_CONFIG_23_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_23_MEM_GPIO_PAD_CONFIG_23_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_24 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_24_MEM_GPIO_PAD_CONFIG_24_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_24_MEM_GPIO_PAD_CONFIG_24_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_25 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_25_MEM_GPIO_PAD_CONFIG_25_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_25_MEM_GPIO_PAD_CONFIG_25_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_26 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_26_MEM_GPIO_PAD_CONFIG_26_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_26_MEM_GPIO_PAD_CONFIG_26_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_27 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_27_MEM_GPIO_PAD_CONFIG_27_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_27_MEM_GPIO_PAD_CONFIG_27_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_28 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_28_MEM_GPIO_PAD_CONFIG_28_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_28_MEM_GPIO_PAD_CONFIG_28_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_29 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_29_MEM_GPIO_PAD_CONFIG_29_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_29_MEM_GPIO_PAD_CONFIG_29_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_30 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_30_MEM_GPIO_PAD_CONFIG_30_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_30_MEM_GPIO_PAD_CONFIG_30_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_31 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_31_MEM_GPIO_PAD_CONFIG_31_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_31_MEM_GPIO_PAD_CONFIG_31_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_32 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_32_MEM_GPIO_PAD_CONFIG_32_M \
0x00000FFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." it can be used
// for I2C type of peripherals. 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_32_MEM_GPIO_PAD_CONFIG_32_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_33 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_33_MEM_GPIO_PAD_CONFIG_33_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_33_MEM_GPIO_PAD_CONFIG_33_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_34 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_34_MEM_GPIO_PAD_CONFIG_34_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_34_MEM_GPIO_PAD_CONFIG_34_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_35 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_35_MEM_GPIO_PAD_CONFIG_35_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_35_MEM_GPIO_PAD_CONFIG_35_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_36 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_36_MEM_GPIO_PAD_CONFIG_36_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_36_MEM_GPIO_PAD_CONFIG_36_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_37 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_37_MEM_GPIO_PAD_CONFIG_37_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_37_MEM_GPIO_PAD_CONFIG_37_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_38 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_38_MEM_GPIO_PAD_CONFIG_38_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_38_MEM_GPIO_PAD_CONFIG_38_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_39 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_39_MEM_GPIO_PAD_CONFIG_39_M \
0x0000003F // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 5 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'. IODEN and I8MAEN
// is diesabled for all development
// IO's. These signals are tied to
// logic level '0'. common control
// is implemented for I2MAEN,
// I4MAEN, WKPU, WKPD control .
// refer dev_pad_cmn_config register
// bits.
#define OCP_SHARED_GPIO_PAD_CONFIG_39_MEM_GPIO_PAD_CONFIG_39_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CONFIG_40 register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CONFIG_40_MEM_GPIO_PAD_CONFIG_40_M \
0x0007FFFF // GPIO 0 register: "Bit 0 - 3 is
// used for PAD IO mode selection.
// io_register={ "" 0 =>
// """"CONFMODE[0]"""""" "" 1 =>
// """"CONFMODE[1]"""""" "" 2 =>
// """"CONFMODE[2]"""""" "" 3 =>
// """"CONFMODE[3]"""" 4 =>
// """"IODEN"""" --> When level ‘1’
// this disables the PMOS xtors of
// the output stages making them
// open-drain type." "For example in
// case of I2C Value gets latched at
// rising edge of RET33.""" """ 5 =>
// """"I2MAEN"""" --> Level ‘1’
// enables the approx 2mA output
// stage""" """ 6 => """"I4MAEN""""
// --> Level ‘1’ enables the approx
// 4mA output stage""" """ 7 =>
// """"I8MAEN"""" --> Level ‘1’
// enables the approx 8mA output
// stage. Note: any drive strength
// between 2mA and 14mA can be
// obtained with combination of 2mA
// 4mA and 8mA.""" """ 8 =>
// """"IWKPUEN"""" --> 10uA pull up
// (weak strength)""" """ 9 =>
// """"IWKPDEN"""" --> 10uA pull
// down (weak strength)""" """ 10 =>
// """"IOE_N"""" --> output enable
// value. level ‘0’ enables the IDO
// to PAD path. Else PAD is
// tristated (except for the PU/PD
// which are independent)." "Value
// gets latched at rising edge of
// RET33""" """ 11 =>""""
// IOE_N_OV"""" --> output enable
// overirde. when bit is set to
// logic '1' IOE_N (bit 4) value
// will control IO IOE_N signal else
// IOE_N is control via selected HW
// logic. strong PULL UP and PULL
// Down control is disabled for all
// IO's. both controls are tied to
// logic level '0'.
#define OCP_SHARED_GPIO_PAD_CONFIG_40_MEM_GPIO_PAD_CONFIG_40_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_GPIO_PAD_CMN_CONFIG register.
//
//******************************************************************************
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_D2D_ISO_A_EN \
0x00000080 // when '1' enable ISO A control to
// D2D Pads else ISO is disabled.
// For these PADS to be functional
// this signals should be set 0.
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_D2D_ISO_Y_EN \
0x00000040 // when '1' enable ISO Y control to
// D2D Pads else ISO is disabled.
// For these PADS to be functional
// this signals should be set 0.
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_JTAG_IDIEN \
0x00000020 // If level ‘1’ enables the PAD to
// ODI path for JTAG PADS [PAD 23,
// 24, 28, 29]. Else ODI is pulled
// ‘Low’ regardless of PAD level."
// "Value gets latched at rising
// edge of RET33.""" """
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_HYSTVAL_M \
0x00000018 // 00’: hysteriris = 10% of VDDS
// (difference between upper and
// lower threshold of the schmit
// trigger) ‘01’: hysteriris = 20%
// of VDDS (difference between upper
// and lower threshold of the schmit
// trigger) ‘10’: hysteriris = 30%
// of VDDS (difference between upper
// and lower threshold of the schmit
// trigger) ‘11’: hysteriris = 40%
// of VDDS (difference between upper
// and lower threshold of the schmit
// trigger)" """
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_HYSTVAL_S 3
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_HYSTEN \
0x00000004 // If logic ‘0’ there is no
// hysteresis. Set to ‘1’ to enable
// hysteresis. Leave the choice to
// customers"""
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_IBIASEN \
0x00000002 // Normal functional operation set
// this to logic ‘1’ to increase the
// speed of the o/p buffer at the
// cost of 0.2uA static current
// consumption per IO. During IDDQ
// test and during Hibernate this
// would be forced to logic ‘0’.
// Value is not latched at rising
// edge of RET33.""
#define OCP_SHARED_GPIO_PAD_CMN_CONFIG_MEM_PAD_IDIEN \
0x00000001 // If level ‘1’ enables the PAD to
// ODI path. Else ODI is pulled
// ‘Low’ regardless of PAD level."
// "Value gets latched at rising
// edge of RET33.""" """
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_D2D_DEV_PAD_CMN_CONFIG register.
//
//******************************************************************************
#define OCP_SHARED_D2D_DEV_PAD_CMN_CONFIG_MEM_DEV_PAD_CMN_CONF_M \
0x0000003F // this register implements common
// IO control to all devement mode
// PADs; these PADs are DEV_PAD33 to
// DEV_PAD39. Bit [1:0] : Drive
// strength control. These 2 bits
// are connected to DEV PAD drive
// strength control. possible drive
// stregnths are 2MA, 4MA and 6 MA
// for the these IO's. bit 0: when
// set to logic value '1' enable 2MA
// drive strength for DEVPAD01 to 07
// bit 1: when set to logic value
// '1' enable 4MA drive strength for
// DEVPAD01 to 07. bit[3:2] : WK
// PULL UP and PULL down control.
// These 2 bits provide IWKPUEN and
// IWKPDEN control for all DEV IO's.
// bit 2: when set to logic value
// '1' enable WKPU to DEVPAD01 to 07
// bit 3: when set to logic value
// '1' enable WKPD to DEVPAD01 to
// 07. bit 4: WK PULL control for
// DEV_PKG_DETECT pin. when '1'
// pullup enabled else it is
// disable. bit 5: when set to logic
// value '1' enable 8MA drive
// strength for DEVPAD01 to 07.
#define OCP_SHARED_D2D_DEV_PAD_CMN_CONFIG_MEM_DEV_PAD_CMN_CONF_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_D2D_TOSTACK_PAD_CONF register.
//
//******************************************************************************
#define OCP_SHARED_D2D_TOSTACK_PAD_CONF_MEM_D2D_TOSTACK_PAD_CONF_M \
0x1FFFFFFF // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
// this register control OEN2X pin
// of D2D TOSTACK PAD: OEN1X and
// OEN2X decoding is as follows:
// "when ""00"" :" "when ""01"" :
// dirve strength is '1' and output
// buffer enabled." "when ""10"" :
// drive strength is 2 and output
// buffer is disabled." "when ""11""
// : dirve strength is '3' and
// output buffer enabled."
#define OCP_SHARED_D2D_TOSTACK_PAD_CONF_MEM_D2D_TOSTACK_PAD_CONF_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_D2D_MISC_PAD_CONF register.
//
//******************************************************************************
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_POR_RESET_N \
0x00000200 // This register provide OEN2X
// control to D2D PADS OEN/OEN2X
// control. When 0 : Act as input
// buffer else output buffer with
// drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_RESET_N \
0x00000100 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_HCLK \
0x00000080 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_JTAG_TCK \
0x00000040 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_JTAG_TMS \
0x00000020 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_JTAG_TDI \
0x00000010 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_PIOSC \
0x00000008 // OEN/OEN2X control. When 0 : Act
// as input buffer else output
// buffer with drive strength 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_SPARE_M \
0x00000007 // D2D SPARE PAD OEN/OEN2X control.
// When 0: Act as input buffer else
// output buffer with drive strength
// 2.
#define OCP_SHARED_D2D_MISC_PAD_CONF_MEM_D2D_SPARE_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SOP_CONF_OVERRIDE register.
//
//******************************************************************************
#define OCP_SHARED_SOP_CONF_OVERRIDE_MEM_SOP_CONF_OVERRIDE \
0x00000001 // when '1' : signal will ovberride
// SoP setting of JTAG PADS. when
// '0': SoP setting will control
// JTAG PADs [ TDI, TDO, TMS, TCK]
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_DEBUGSS_STATUS register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_APPS_MCU_JTAGNSW \
0x00000020 // This register contains debug
// subsystem status bits From APPS
// MCU status bit to indicates
// whether serial wire or 4 pins
// jtag select.
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_CJTAG_BYPASS_STATUS \
0x00000010 // cjtag bypass bit select
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_SW_INTERFACE_SEL_STATUS \
0x00000008 // serial wire interface bit select
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_APPS_TAP_ENABLE_STATUS \
0x00000004 // apps tap enable status
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_TAPS_ENABLE_STATUS \
0x00000002 // tap enable status
#define OCP_SHARED_CC3XX_DEBUGSS_STATUS_SSBD_UNLOCK \
0x00000001 // ssbd unlock status
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_DEBUGMUX_SEL register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_DEBUGMUX_SEL_MEM_CC3XX_DEBUGMUX_SEL_M \
0x0000FFFF // debug mux select register. Upper
// 8 bits are used for debug module
// selection. Lower 8 bit [7:0] used
// inside debug module for selecting
// module specific signals.
// Bits[15:8: when set x"00" : GPRCM
// debug bus. When "o1" : SDIO debug
// debug bus when x"02" :
// autonoumous SPI when x"03" :
// TOPIC when x"04": memss when
// x"25": mcu debug bus : APPS debug
// when x"45": mcu debug bus : NWP
// debug when x"65": mcu debug bus :
// AHB2VBUS debug when x"85": mcu
// debug bus : VBUS2HAB debug when
// x"95": mcu debug bus : RCM debug
// when x"A5": mcu debug bus :
// crypto debug when x"06": WLAN
// debug bus when x"07": debugss bus
// when x"08": ADC debug when x"09":
// SDIO PHY debug bus then "others"
// : no debug is selected
#define OCP_SHARED_CC3XX_DEBUGMUX_SEL_MEM_CC3XX_DEBUGMUX_SEL_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_ALT_PC_VAL_NW register.
//
//******************************************************************************
#define OCP_SHARED_ALT_PC_VAL_NW_MEM_ALT_PC_VAL_NW_M \
0xFFFFFFFF // 32 bit. Program counter value
// for 0x4 address when Alt_pc_en_nw
// is set.
#define OCP_SHARED_ALT_PC_VAL_NW_MEM_ALT_PC_VAL_NW_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_ALT_PC_VAL_APPS register.
//
//******************************************************************************
#define OCP_SHARED_ALT_PC_VAL_APPS_MEM_ALT_PC_VAL_APPS_M \
0xFFFFFFFF // 32 bit. Program counter value
// for 0x4 address when
// Alt_pc_en_apps is set
#define OCP_SHARED_ALT_PC_VAL_APPS_MEM_ALT_PC_VAL_APPS_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_4 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_4_MEM_SPARE_REG_4_M \
0xFFFFFFFE // HW register
#define OCP_SHARED_SPARE_REG_4_MEM_SPARE_REG_4_S 1
#define OCP_SHARED_SPARE_REG_4_INVERT_D2D_INTERFACE \
0x00000001 // Data to the top die launched at
// negative edge instead of positive
// edge.
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_5 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_5_MEM_SPARE_REG_5_M \
0xFFFFFFFF // HW register
#define OCP_SHARED_SPARE_REG_5_MEM_SPARE_REG_5_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SH_SPI_CS_MASK register.
//
//******************************************************************************
#define OCP_SHARED_SH_SPI_CS_MASK_MEM_SH_SPI_CS_MASK_M \
0x0000000F // ( chip select 0 is unmasked
// after reset. When ‘1’ : CS is
// unmasked or else masked. Valid
// configurations are 1000, 0100,
// 0010 or 0001. Any other setting
// can lead to unpredictable
// behavior.
#define OCP_SHARED_SH_SPI_CS_MASK_MEM_SH_SPI_CS_MASK_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_DEVICE_TYPE register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_DEVICE_TYPE_DEVICE_TYPE_reserved_M \
0x00000060 // reserved bits tied off "00".
#define OCP_SHARED_CC3XX_DEVICE_TYPE_DEVICE_TYPE_reserved_S 5
#define OCP_SHARED_CC3XX_DEVICE_TYPE_DEVICE_TYPE_M \
0x0000001F // CC3XX Device type information.
#define OCP_SHARED_CC3XX_DEVICE_TYPE_DEVICE_TYPE_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_MEM_TOPMUXCTRL_IFORCE register.
//
//******************************************************************************
#define OCP_SHARED_MEM_TOPMUXCTRL_IFORCE_MEM_TOPMUXCTRL_IFORCE1_M \
0x000000F0 // [4] 1: switch between
// WLAN_I2C_SCL and
// TOP_GPIO_PORT4_I2C closes 0:
// switch opens [5] 1: switch
// between WLAN_I2C_SCL and
// TOP_VSENSE_PORT closes 0: switch
// opens [6] 1: switch between
// WLAN_I2C_SCL and WLAN_ANA_TP4
// closes 0: switch opens [7]
// Reserved
#define OCP_SHARED_MEM_TOPMUXCTRL_IFORCE_MEM_TOPMUXCTRL_IFORCE1_S 4
#define OCP_SHARED_MEM_TOPMUXCTRL_IFORCE_MEM_TOPMUXCTRL_IFORCE_M \
0x0000000F // [0] 1: switch between
// WLAN_I2C_SDA and
// TOP_GPIO_PORT3_I2C closes 0:
// switch opens [1] 1: switch
// between WLAN_I2C_SDA and
// TOP_IFORCE_PORT closes 0: switch
// opens [2] 1: switch between
// WLAN_I2C_SDA and WLAN_ANA_TP3
// closes 0: switch opens [3]
// Reserved
#define OCP_SHARED_MEM_TOPMUXCTRL_IFORCE_MEM_TOPMUXCTRL_IFORCE_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_DEV_PACKAGE_DETECT register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_DEV_PACKAGE_DETECT_DEV_PKG_DETECT \
0x00000001 // when '0' indicates package type
// is development.
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_AUTONMS_SPICLK_SEL register.
//
//******************************************************************************
#define OCP_SHARED_AUTONMS_SPICLK_SEL_MEM_AUTONOMOUS_BYPASS \
0x00000002 // This bit is used to bypass MCPSI
// autonomous mode .if this bit is 1
// autonomous MCSPI logic will be
// bypassed and it will act as link
// SPI
#define OCP_SHARED_AUTONMS_SPICLK_SEL_MEM_AUTONMS_SPICLK_SEL \
0x00000001 // This bit is used in SPI
// Autonomous mode to switch clock
// from system clock to SPI clk that
// is coming from PAD. When value 1
// PAD SPI clk is used as system
// clock in LPDS mode by SPI as well
// as autonomous wrapper logic.
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_CC3XX_DEV_PADCONF register.
//
//******************************************************************************
#define OCP_SHARED_CC3XX_DEV_PADCONF_MEM_CC3XX_DEV_PADCONF_M \
0x0000FFFF
#define OCP_SHARED_CC3XX_DEV_PADCONF_MEM_CC3XX_DEV_PADCONF_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_IDMEM_TIM_UPDATE register.
//
//******************************************************************************
#define OCP_SHARED_IDMEM_TIM_UPDATE_MEM_IDMEM_TIM_UPDATE_M \
0xFFFFFFFF
#define OCP_SHARED_IDMEM_TIM_UPDATE_MEM_IDMEM_TIM_UPDATE_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_6 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_6_MEM_SPARE_REG_6_M \
0xFFFFFFFF // NWP Software register
#define OCP_SHARED_SPARE_REG_6_MEM_SPARE_REG_6_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_SPARE_REG_7 register.
//
//******************************************************************************
#define OCP_SHARED_SPARE_REG_7_MEM_SPARE_REG_7_M \
0xFFFFFFFF // NWP Software register
#define OCP_SHARED_SPARE_REG_7_MEM_SPARE_REG_7_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_APPS_WLAN_ORBIT register.
//
//******************************************************************************
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_spare_M \
0xFFFFFC00 // Spare bit
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_spare_S 10
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_test_status \
0x00000200 // A rising edge on this bit
// indicates that the test case
// passes. This bit would be brought
// out on the pin interface during
// ORBIT.
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_test_exec \
0x00000100 // This register bit is writable by
// the FW and when set to 1 it
// indicates the start of a test
// execution. A failing edge on this
// bit indicates that the test
// execution is complete. This bit
// would be brought out on the pin
// interface during ORBIT.
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_test_id_M \
0x000000FC // Implies the test case ID that
// needs to run.
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_test_id_S 2
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_halt_proc \
0x00000002 // This bit is used to trigger the
// execution of test cases within
// the (ROM based) IP.
#define OCP_SHARED_APPS_WLAN_ORBIT_mem_orbit_test_mode \
0x00000001 // When this bit is 1 it implies
// ORBIT mode of operation and the
// (ROM based) IP start the
// execution from a test case
// perspective
//******************************************************************************
//
// The following are defines for the bit fields in the
// OCP_SHARED_O_APPS_WLAN_SCRATCH_PAD register.
//
//******************************************************************************
#define OCP_SHARED_APPS_WLAN_SCRATCH_PAD_MEM_APPS_WLAN_SCRATCH_PAD_M \
0xFFFFFFFF // scratch pad register.
#define OCP_SHARED_APPS_WLAN_SCRATCH_PAD_MEM_APPS_WLAN_SCRATCH_PAD_S 0
#endif // __HW_OCP_SHARED_H__
Reference in New Issue View Git Blame Copy Permalink