8f26d181c3
Everything works fine without USB being plugged in but faults (I think) when USB is plugged in. This is switched away from the USB code from the bootloader onto the USB code thats generated by Atmel Studio using the high level classes from ASF.
110 lines
3.8 KiB
C
110 lines
3.8 KiB
C
/**
|
|
* \file
|
|
*
|
|
* \brief SAM GPIO Port Driver
|
|
*
|
|
* Copyright (C) 2012-2015 Atmel Corporation. All rights reserved.
|
|
*
|
|
* \asf_license_start
|
|
*
|
|
* \page License
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the following disclaimer.
|
|
*
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
*
|
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* 4. This software may only be redistributed and used in connection with an
|
|
* Atmel microcontroller product.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* \asf_license_stop
|
|
*
|
|
*/
|
|
/*
|
|
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
|
*/
|
|
#include <port.h>
|
|
|
|
/**
|
|
* \brief Writes a Port pin configuration to the hardware module.
|
|
*
|
|
* Writes out a given configuration of a Port pin configuration to the hardware
|
|
* module.
|
|
*
|
|
* \note If the pin direction is set as an output, the pull-up/pull-down input
|
|
* configuration setting is ignored.
|
|
*
|
|
* \param[in] gpio_pin Index of the GPIO pin to configure
|
|
* \param[in] config Configuration settings for the pin
|
|
*/
|
|
void port_pin_set_config(
|
|
const uint8_t gpio_pin,
|
|
const struct port_config *const config)
|
|
{
|
|
/* Sanity check arguments */
|
|
Assert(config);
|
|
|
|
struct system_pinmux_config pinmux_config;
|
|
system_pinmux_get_config_defaults(&pinmux_config);
|
|
|
|
pinmux_config.mux_position = SYSTEM_PINMUX_GPIO;
|
|
pinmux_config.direction = (enum system_pinmux_pin_dir)config->direction;
|
|
pinmux_config.input_pull = (enum system_pinmux_pin_pull)config->input_pull;
|
|
pinmux_config.powersave = config->powersave;
|
|
|
|
system_pinmux_pin_set_config(gpio_pin, &pinmux_config);
|
|
}
|
|
|
|
/**
|
|
* \brief Writes a Port group configuration group to the hardware module.
|
|
*
|
|
* Writes out a given configuration of a Port group configuration to the
|
|
* hardware module.
|
|
*
|
|
* \note If the pin direction is set as an output, the pull-up/pull-down input
|
|
* configuration setting is ignored.
|
|
*
|
|
* \param[out] port Base of the PORT module to write to
|
|
* \param[in] mask Mask of the port pin(s) to configure
|
|
* \param[in] config Configuration settings for the pin group
|
|
*/
|
|
void port_group_set_config(
|
|
PortGroup *const port,
|
|
const uint32_t mask,
|
|
const struct port_config *const config)
|
|
{
|
|
/* Sanity check arguments */
|
|
Assert(port);
|
|
Assert(config);
|
|
|
|
struct system_pinmux_config pinmux_config;
|
|
system_pinmux_get_config_defaults(&pinmux_config);
|
|
|
|
pinmux_config.mux_position = SYSTEM_PINMUX_GPIO;
|
|
pinmux_config.direction = (enum system_pinmux_pin_dir)config->direction;
|
|
pinmux_config.input_pull = (enum system_pinmux_pin_pull)config->input_pull;
|
|
pinmux_config.powersave = config->powersave;
|
|
|
|
system_pinmux_group_set_config(port, mask, &pinmux_config);
|
|
}
|