circuitpython/ports/stm32/boards/PYBV10/mpconfigboard.h

100 lines
3.6 KiB
C

#define MICROPY_HW_BOARD_NAME "PYBv1.0"
#define MICROPY_HW_MCU_NAME "STM32F405RG"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_HAS_MMA7660 (1)
#define MICROPY_HW_HAS_LCD (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_CAN (1)
#define MICROPY_HW_ENABLE_USB (1)
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
#define MICROPY_HW_CLK_LAST_FREQ (1)
// The pyboard has a 32kHz crystal for the RTC
#define MICROPY_HW_RTC_USE_LSE (1)
#define MICROPY_HW_RTC_USE_US (0)
#define MICROPY_HW_RTC_USE_CALOUT (1)
// UART config
#define MICROPY_HW_UART1_NAME "XB"
#define MICROPY_HW_UART1_TX (pin_B6)
#define MICROPY_HW_UART1_RX (pin_B7)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART3_NAME "YB"
#define MICROPY_HW_UART3_TX (pin_B10)
#define MICROPY_HW_UART3_RX (pin_B11)
#define MICROPY_HW_UART3_RTS (pin_B14)
#define MICROPY_HW_UART3_CTS (pin_B13)
#define MICROPY_HW_UART4_NAME "XA"
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
#define MICROPY_HW_UART6_NAME "YA"
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
// I2C busses
#define MICROPY_HW_I2C1_NAME "X"
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_NAME "Y"
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// SPI busses
#define MICROPY_HW_SPI1_NAME "X"
#define MICROPY_HW_SPI1_NSS (pin_A4) // X5
#define MICROPY_HW_SPI1_SCK (pin_A5) // X6
#define MICROPY_HW_SPI1_MISO (pin_A6) // X7
#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8
#define MICROPY_HW_SPI2_NAME "Y"
#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5
#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6
#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7
#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8
// CAN busses
#define MICROPY_HW_CAN1_NAME "YA" // CAN1 on RX,TX = Y3,Y4 = PB8,PB9
#define MICROPY_HW_CAN2_NAME "YB" // CAN2 on RX,TX = Y5,Y6 = PB12,PB13
// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
#define MICROPY_HW_USRSW_PIN (pin_B3)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// The pyboard has 4 LEDs
#define MICROPY_HW_LED1 (pin_A13) // red
#define MICROPY_HW_LED2 (pin_A14) // green
#define MICROPY_HW_LED3 (pin_A15) // yellow
#define MICROPY_HW_LED4 (pin_B4) // blue
#define MICROPY_HW_LED3_PWM { TIM2, 2, TIM_CHANNEL_1, GPIO_AF1_TIM2 }
#define MICROPY_HW_LED4_PWM { TIM3, 3, TIM_CHANNEL_1, GPIO_AF2_TIM3 }
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
// MMA accelerometer config
#define MICROPY_HW_MMA_AVDD_PIN (pin_B5)