241 lines
9.7 KiB
ReStructuredText
241 lines
9.7 KiB
ReStructuredText
.. currentmodule:: pyb
|
|
.. _pyb.UART:
|
|
|
|
class UART -- duplex serial communication bus
|
|
=============================================
|
|
|
|
UART implements the standard UART/USART duplex serial communications protocol. At
|
|
the physical level it consists of 2 lines: RX and TX. The unit of communication
|
|
is a character (not to be confused with a string character) which can be 8 or 9
|
|
bits wide.
|
|
|
|
UART objects can be created and initialised using::
|
|
|
|
from pyb import UART
|
|
|
|
uart = UART(1, 9600) # init with given baudrate
|
|
uart.init(9600, bits=8, parity=None, stop=1) # init with given parameters
|
|
|
|
Bits can be 7, 8 or 9. Parity can be None, 0 (even) or 1 (odd). Stop can be 1 or 2.
|
|
|
|
*Note:* with parity=None, only 8 and 9 bits are supported. With parity enabled,
|
|
only 7 and 8 bits are supported.
|
|
|
|
A UART object acts like a `stream` object and reading and writing is done
|
|
using the standard stream methods::
|
|
|
|
uart.read(10) # read 10 characters, returns a bytes object
|
|
uart.read() # read all available characters
|
|
uart.readline() # read a line
|
|
uart.readinto(buf) # read and store into the given buffer
|
|
uart.write('abc') # write the 3 characters
|
|
|
|
Individual characters can be read/written using::
|
|
|
|
uart.readchar() # read 1 character and returns it as an integer
|
|
uart.writechar(42) # write 1 character
|
|
|
|
To check if there is anything to be read, use::
|
|
|
|
uart.any() # returns the number of characters waiting
|
|
|
|
|
|
*Note:* The stream functions ``read``, ``write``, etc. are new in MicroPython v1.3.4.
|
|
Earlier versions use ``uart.send`` and ``uart.recv``.
|
|
|
|
Constructors
|
|
------------
|
|
|
|
.. class:: pyb.UART(bus, ...)
|
|
|
|
Construct a UART object on the given bus.
|
|
For Pyboard ``bus`` can be 1-4, 6, 'XA', 'XB', 'YA', or 'YB'.
|
|
For Pyboard Lite ``bus`` can be 1, 2, 6, 'XB', or 'YA'.
|
|
For Pyboard D ``bus`` can be 1-4, 'XA', 'YA' or 'YB'.
|
|
With no additional parameters, the UART object is created but not
|
|
initialised (it has the settings from the last initialisation of
|
|
the bus, if any). If extra arguments are given, the bus is initialised.
|
|
See ``init`` for parameters of initialisation.
|
|
|
|
The physical pins of the UART busses on Pyboard are:
|
|
|
|
- ``UART(4)`` is on ``XA``: ``(TX, RX) = (X1, X2) = (PA0, PA1)``
|
|
- ``UART(1)`` is on ``XB``: ``(TX, RX) = (X9, X10) = (PB6, PB7)``
|
|
- ``UART(6)`` is on ``YA``: ``(TX, RX) = (Y1, Y2) = (PC6, PC7)``
|
|
- ``UART(3)`` is on ``YB``: ``(TX, RX) = (Y9, Y10) = (PB10, PB11)``
|
|
- ``UART(2)`` is on: ``(TX, RX) = (X3, X4) = (PA2, PA3)``
|
|
|
|
The Pyboard Lite supports UART(1), UART(2) and UART(6) only, pins are:
|
|
|
|
- ``UART(1)`` is on ``XB``: ``(TX, RX) = (X9, X10) = (PB6, PB7)``
|
|
- ``UART(6)`` is on ``YA``: ``(TX, RX) = (Y1, Y2) = (PC6, PC7)``
|
|
- ``UART(2)`` is on: ``(TX, RX) = (X1, X2) = (PA2, PA3)``
|
|
|
|
The Pyboard D supports UART(1), UART(2), UART(3) and UART(4) only, pins are:
|
|
|
|
- ``UART(4)`` is on ``XA``: ``(TX, RX) = (X1, X2) = (PA0, PA1)``
|
|
- ``UART(1)`` is on ``YA``: ``(TX, RX) = (Y1, Y2) = (PA9, PA10)``
|
|
- ``UART(3)`` is on ``YB``: ``(TX, RX) = (Y9, Y10) = (PB10, PB11)``
|
|
- ``UART(2)`` is on: ``(TX, RX) = (X3, X4) = (PA2, PA3)``
|
|
|
|
*Note:* Pyboard D has ``UART(1)`` on ``YA``, unlike Pyboard and Pyboard Lite that both
|
|
have ``UART(1)`` on ``XB`` and ``UART(6)`` on ``YA``.
|
|
|
|
Methods
|
|
-------
|
|
|
|
.. method:: UART.init(baudrate, bits=8, parity=None, stop=1, \*, timeout=0, flow=0, timeout_char=0, read_buf_len=64)
|
|
|
|
Initialise the UART bus with the given parameters:
|
|
|
|
- ``baudrate`` is the clock rate.
|
|
- ``bits`` is the number of bits per character, 7, 8 or 9.
|
|
- ``parity`` is the parity, ``None``, 0 (even) or 1 (odd).
|
|
- ``stop`` is the number of stop bits, 1 or 2.
|
|
- ``flow`` sets the flow control type. Can be 0, ``UART.RTS``, ``UART.CTS``
|
|
or ``UART.RTS | UART.CTS``.
|
|
- ``timeout`` is the timeout in milliseconds to wait for writing/reading the first character.
|
|
- ``timeout_char`` is the timeout in milliseconds to wait between characters while writing or reading.
|
|
- ``read_buf_len`` is the character length of the read buffer (0 to disable).
|
|
|
|
This method will raise an exception if the baudrate could not be set within
|
|
5% of the desired value. The minimum baudrate is dictated by the frequency
|
|
of the bus that the UART is on; UART(1) and UART(6) are APB2, the rest are on
|
|
APB1. The default bus frequencies give a minimum baudrate of 1300 for
|
|
UART(1) and UART(6) and 650 for the others. Use :func:`pyb.freq <pyb.freq>`
|
|
to reduce the bus frequencies to get lower baudrates.
|
|
|
|
*Note:* with parity=None, only 8 and 9 bits are supported. With parity enabled,
|
|
only 7 and 8 bits are supported.
|
|
|
|
.. method:: UART.deinit()
|
|
|
|
Turn off the UART bus.
|
|
|
|
.. method:: UART.any()
|
|
|
|
Returns the number of bytes waiting (may be 0).
|
|
|
|
.. method:: UART.read([nbytes])
|
|
|
|
Read characters. If ``nbytes`` is specified then read at most that many bytes.
|
|
If ``nbytes`` are available in the buffer, returns immediately, otherwise returns
|
|
when sufficient characters arrive or the timeout elapses.
|
|
|
|
If ``nbytes`` is not given then the method reads as much data as possible. It
|
|
returns after the timeout has elapsed.
|
|
|
|
*Note:* for 9 bit characters each character takes two bytes, ``nbytes`` must
|
|
be even, and the number of characters is ``nbytes/2``.
|
|
|
|
Return value: a bytes object containing the bytes read in. Returns ``None``
|
|
on timeout.
|
|
|
|
.. method:: UART.readchar()
|
|
|
|
Receive a single character on the bus.
|
|
|
|
Return value: The character read, as an integer. Returns -1 on timeout.
|
|
|
|
.. method:: UART.readinto(buf[, nbytes])
|
|
|
|
Read bytes into the ``buf``. If ``nbytes`` is specified then read at most
|
|
that many bytes. Otherwise, read at most ``len(buf)`` bytes.
|
|
|
|
Return value: number of bytes read and stored into ``buf`` or ``None`` on
|
|
timeout.
|
|
|
|
.. method:: UART.readline()
|
|
|
|
Read a line, ending in a newline character. If such a line exists, return is
|
|
immediate. If the timeout elapses, all available data is returned regardless
|
|
of whether a newline exists.
|
|
|
|
Return value: the line read or ``None`` on timeout if no data is available.
|
|
|
|
.. method:: UART.write(buf)
|
|
|
|
Write the buffer of bytes to the bus. If characters are 7 or 8 bits wide
|
|
then each byte is one character. If characters are 9 bits wide then two
|
|
bytes are used for each character (little endian), and ``buf`` must contain
|
|
an even number of bytes.
|
|
|
|
Return value: number of bytes written. If a timeout occurs and no bytes
|
|
were written returns ``None``.
|
|
|
|
.. method:: UART.writechar(char)
|
|
|
|
Write a single character on the bus. ``char`` is an integer to write.
|
|
Return value: ``None``. See note below if CTS flow control is used.
|
|
|
|
.. method:: UART.sendbreak()
|
|
|
|
Send a break condition on the bus. This drives the bus low for a duration
|
|
of 13 bits.
|
|
Return value: ``None``.
|
|
|
|
Constants
|
|
---------
|
|
|
|
.. data:: UART.RTS
|
|
UART.CTS
|
|
|
|
to select the flow control type.
|
|
|
|
Flow Control
|
|
------------
|
|
|
|
On Pyboards V1 and V1.1 ``UART(2)`` and ``UART(3)`` support RTS/CTS hardware flow control
|
|
using the following pins:
|
|
|
|
- ``UART(2)`` is on: ``(TX, RX, nRTS, nCTS) = (X3, X4, X2, X1) = (PA2, PA3, PA1, PA0)``
|
|
- ``UART(3)`` is on :``(TX, RX, nRTS, nCTS) = (Y9, Y10, Y7, Y6) = (PB10, PB11, PB14, PB13)``
|
|
|
|
On the Pyboard Lite only ``UART(2)`` supports flow control on these pins:
|
|
|
|
``(TX, RX, nRTS, nCTS) = (X1, X2, X4, X3) = (PA2, PA3, PA1, PA0)``
|
|
|
|
In the following paragraphs the term "target" refers to the device connected to
|
|
the UART.
|
|
|
|
When the UART's ``init()`` method is called with ``flow`` set to one or both of
|
|
``UART.RTS`` and ``UART.CTS`` the relevant flow control pins are configured.
|
|
``nRTS`` is an active low output, ``nCTS`` is an active low input with pullup
|
|
enabled. To achieve flow control the Pyboard's ``nCTS`` signal should be connected
|
|
to the target's ``nRTS`` and the Pyboard's ``nRTS`` to the target's ``nCTS``.
|
|
|
|
CTS: target controls Pyboard transmitter
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
If CTS flow control is enabled the write behaviour is as follows:
|
|
|
|
If the Pyboard's ``UART.write(buf)`` method is called, transmission will stall for
|
|
any periods when ``nCTS`` is ``False``. This will result in a timeout if the entire
|
|
buffer was not transmitted in the timeout period. The method returns the number of
|
|
bytes written, enabling the user to write the remainder of the data if required. In
|
|
the event of a timeout, a character will remain in the UART pending ``nCTS``. The
|
|
number of bytes composing this character will be included in the return value.
|
|
|
|
If ``UART.writechar()`` is called when ``nCTS`` is ``False`` the method will time
|
|
out unless the target asserts ``nCTS`` in time. If it times out ``OSError 116``
|
|
will be raised. The character will be transmitted as soon as the target asserts ``nCTS``.
|
|
|
|
RTS: Pyboard controls target's transmitter
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
If RTS flow control is enabled, behaviour is as follows:
|
|
|
|
If buffered input is used (``read_buf_len`` > 0), incoming characters are buffered.
|
|
If the buffer becomes full, the next character to arrive will cause ``nRTS`` to go
|
|
``False``: the target should cease transmission. ``nRTS`` will go ``True`` when
|
|
characters are read from the buffer.
|
|
|
|
Note that the ``any()`` method returns the number of bytes in the buffer. Assume a
|
|
buffer length of ``N`` bytes. If the buffer becomes full, and another character arrives,
|
|
``nRTS`` will be set False, and ``any()`` will return the count ``N``. When
|
|
characters are read the additional character will be placed in the buffer and will
|
|
be included in the result of a subsequent ``any()`` call.
|
|
|
|
If buffered input is not used (``read_buf_len`` == 0) the arrival of a character will
|
|
cause ``nRTS`` to go ``False`` until the character is read.
|