5c32111fa0
These files that are reformatted only now fall under the list of files to apply uncrustify/black formatting to. Signed-off-by: Damien George <damien@micropython.org>
101 lines
3.5 KiB
C
101 lines
3.5 KiB
C
// The Sparkfun MicroMod spec uses a zero-based peripheral numbering scheme.
|
|
// In cases where the 0th peripheral is the default, the "0" is omitted from
|
|
// the name (e.g. "I2C" instead of "I2C0").
|
|
//
|
|
// Note: UART (UART0) is not present in the edge connector pinout because the
|
|
// primary debug serial port is exposed as a virtual serial port over USB,
|
|
// i.e. Serial.print() should print over USB VCP, not UART_TX1.
|
|
//
|
|
// For more details, see https://www.sparkfun.com/micromod#tech-specs
|
|
|
|
#define MICROPY_HW_BOARD_NAME "SparkFun STM32 MicroMod Processor"
|
|
#define MICROPY_HW_MCU_NAME "STM32F405RG"
|
|
|
|
// 1 = use STM32 internal flash (1 MByte)
|
|
// 0 = use onboard external SPI flash (16 MByte)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
// External SPI Flash config
|
|
#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
|
|
|
|
// 128 Mbit (16 MByte) external SPI flash
|
|
#define MICROPY_HW_SPIFLASH_SIZE_BITS (128 * 1024 * 1024)
|
|
|
|
#define MICROPY_HW_SPIFLASH_CS (pin_C3)
|
|
#define MICROPY_HW_SPIFLASH_SCK (pin_C10)
|
|
#define MICROPY_HW_SPIFLASH_MOSI (pin_C12)
|
|
#define MICROPY_HW_SPIFLASH_MISO (pin_C11)
|
|
|
|
#define MICROPY_BOARD_EARLY_INIT board_early_init
|
|
void board_early_init(void);
|
|
|
|
extern const struct _mp_spiflash_config_t spiflash_config;
|
|
extern struct _spi_bdev_t spi_bdev;
|
|
#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1)
|
|
#define MICROPY_HW_BDEV_IOCTL(op, arg) ( \
|
|
(op) == BDEV_IOCTL_NUM_BLOCKS ? (MICROPY_HW_SPIFLASH_SIZE_BITS / 8 / FLASH_BLOCK_SIZE) : \
|
|
(op) == BDEV_IOCTL_INIT ? spi_bdev_ioctl(&spi_bdev, (op), (uint32_t)&spiflash_config) : \
|
|
spi_bdev_ioctl(&spi_bdev, (op), (arg)) \
|
|
)
|
|
#define MICROPY_HW_BDEV_READBLOCKS(dest, bl, n) spi_bdev_readblocks(&spi_bdev, (dest), (bl), (n))
|
|
#define MICROPY_HW_BDEV_WRITEBLOCKS(src, bl, n) spi_bdev_writeblocks(&spi_bdev, (src), (bl), (n))
|
|
#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol
|
|
|
|
#endif // !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
|
|
|
|
// STM32 HSE config
|
|
// The module has a 12 MHz crystal for the HSE oscillator.
|
|
#define MICROPY_HW_CLK_PLLM (12)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
#define MICROPY_HW_CLK_LAST_FREQ (1)
|
|
|
|
// STM32 LSE config
|
|
// The module has a 32.768 kHz crystal for the LSE (RTC).
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
#define MICROPY_HW_RTC_USE_US (0)
|
|
#define MICROPY_HW_RTC_USE_CALOUT (1)
|
|
|
|
// UART2 config (MicroMod UART1)
|
|
#define MICROPY_HW_UART2_NAME "UART1"
|
|
#define MICROPY_HW_UART2_TX (pin_A2)
|
|
#define MICROPY_HW_UART2_RX (pin_A3)
|
|
|
|
// CAN1 config (MicroMod CAN)
|
|
#define MICROPY_HW_CAN1_NAME "CAN"
|
|
#define MICROPY_HW_CAN1_TX (pin_B9)
|
|
#define MICROPY_HW_CAN1_RX (pin_B8)
|
|
|
|
// I2C1 config (MicroMod I2C1)
|
|
#define MICROPY_HW_I2C1_NAME "I2C1"
|
|
#define MICROPY_HW_I2C1_SCL (pin_B6)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B7)
|
|
|
|
// I2C2 config (MicroMod I2C)
|
|
#define MICROPY_HW_I2C2_NAME "I2C"
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
|
|
// SPI1 config (MicroMod SPI)
|
|
#define MICROPY_HW_SPI1_NAME "SPI"
|
|
#define MICROPY_HW_SPI1_NSS (pin_C4)
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
|
|
// LED1 config
|
|
// The module has a single blue status LED.
|
|
#define MICROPY_HW_LED1 (pin_A15)
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB device config
|
|
#define MICROPY_HW_USB_FS (1)
|