171 lines
4.2 KiB
ReStructuredText
171 lines
4.2 KiB
ReStructuredText
:mod:`pyb` --- functions related to the pyboard
|
|
===============================================
|
|
|
|
.. module:: pyb
|
|
:synopsis: functions related to the pyboard
|
|
|
|
The ``pyb`` module contains specific functions related to the pyboard.
|
|
|
|
Time related functions
|
|
----------------------
|
|
|
|
.. function:: delay(ms)
|
|
|
|
Delay for the given number of milliseconds.
|
|
|
|
.. function:: udelay(us)
|
|
|
|
Delay for the given number of microseconds.
|
|
|
|
.. function:: millis()
|
|
|
|
Returns the number of milliseconds since the board was last reset.
|
|
|
|
The result is always a micropython smallint (31-bit signed number), so
|
|
after 2^30 milliseconds (about 12.4 days) this will start to return
|
|
negative numbers.
|
|
|
|
.. function:: micros()
|
|
|
|
Returns the number of microseconds since the board was last reset.
|
|
|
|
The result is always a micropython smallint (31-bit signed number), so
|
|
after 2^30 microseconds (about 17.8 minutes) this will start to return
|
|
negative numbers.
|
|
|
|
.. function:: elapsed_millis(start)
|
|
|
|
Returns the number of milliseconds which have elapsed since ``start``.
|
|
|
|
This function takes care of counter wrap, and always returns a positive
|
|
number. This means it can be used to measure periods upto about 12.4 days.
|
|
|
|
Example::
|
|
|
|
start = pyb.millis()
|
|
while pyb.elapsed_millis(start) < 1000:
|
|
# Perform some operation
|
|
|
|
.. function:: elapsed_micros(start)
|
|
|
|
Returns the number of microseconds which have elapsed since ``start``.
|
|
|
|
This function takes care of counter wrap, and always returns a positive
|
|
number. This means it can be used to measure periods upto about 17.8 minutes.
|
|
|
|
Example::
|
|
|
|
start = pyb.micros()
|
|
while pyb.elapsed_micros(start) < 1000:
|
|
# Perform some operation
|
|
pass
|
|
|
|
Reset related functions
|
|
-----------------------
|
|
|
|
.. function:: hard_reset()
|
|
|
|
Resets the pyboard in a manner similar to pushing the external RESET
|
|
button.
|
|
|
|
.. function:: bootloader()
|
|
|
|
Activate the bootloader without BOOT\* pins.
|
|
|
|
Interrupt related functions
|
|
---------------------------
|
|
|
|
.. function:: disable_irq()
|
|
|
|
Disable interrupt requests.
|
|
Returns the previous IRQ state: ``False``/``True`` for disabled/enabled IRQs
|
|
respectively. This return value can be passed to enable_irq to restore
|
|
the IRQ to its original state.
|
|
|
|
.. function:: enable_irq(state=True)
|
|
|
|
Enable interrupt requests.
|
|
If ``state`` is ``True`` (the default value) then IRQs are enabled.
|
|
If ``state`` is ``False`` then IRQs are disabled. The most common use of
|
|
this function is to pass it the value returned by ``disable_irq`` to
|
|
exit a critical section.
|
|
|
|
Power related functions
|
|
-----------------------
|
|
|
|
.. function:: freq([sys_freq])
|
|
|
|
If given no arguments, returns a tuple of clock frequencies:
|
|
(SYSCLK, HCLK, PCLK1, PCLK2).
|
|
|
|
If given an argument, sets the system frequency to that value in Hz.
|
|
Eg freq(120000000) gives 120MHz. Note that not all values are
|
|
supported and the largest supported frequency not greater than
|
|
the given sys_freq will be selected.
|
|
|
|
.. function:: wfi()
|
|
|
|
Wait for an interrupt.
|
|
This executies a ``wfi`` instruction which reduces power consumption
|
|
of the MCU until an interrupt occurs, at which point execution continues.
|
|
|
|
.. function:: standby()
|
|
|
|
|
|
.. function:: stop()
|
|
|
|
Miscellaneous functions
|
|
-----------------------
|
|
|
|
.. function:: have_cdc()
|
|
|
|
Return True if USB is connected as a serial device, False otherwise.
|
|
|
|
.. function:: hid((buttons, x, y, z))
|
|
|
|
Takes a 4-tuple (or list) and sends it to the USB host (the PC) to
|
|
signal a HID mouse-motion event.
|
|
|
|
.. function:: info([dump_alloc_table])
|
|
|
|
Print out lots of information about the board.
|
|
|
|
.. function:: repl_uart(uart)
|
|
|
|
Get or set the UART object that the REPL is repeated on.
|
|
|
|
.. function:: rng()
|
|
|
|
Return a 30-bit hardware generated random number.
|
|
|
|
.. function:: sync()
|
|
|
|
Sync all file systems.
|
|
|
|
.. function:: unique_id()
|
|
|
|
Returns a string of 12 bytes (96 bits), which is the unique ID for the MCU.
|
|
|
|
Classes
|
|
-------
|
|
|
|
.. toctree::
|
|
:maxdepth: 1
|
|
|
|
pyb.Accel.rst
|
|
pyb.ADC.rst
|
|
pyb.CAN.rst
|
|
pyb.DAC.rst
|
|
pyb.ExtInt.rst
|
|
pyb.I2C.rst
|
|
pyb.LCD.rst
|
|
pyb.LED.rst
|
|
pyb.Pin.rst
|
|
pyb.RTC.rst
|
|
pyb.Servo.rst
|
|
pyb.SPI.rst
|
|
pyb.Switch.rst
|
|
pyb.Timer.rst
|
|
pyb.UART.rst
|
|
pyb.USB_VCP.rst
|