#define NETDUINO_PLUS_2 #define MICROPY_HW_BOARD_NAME "NetduinoPlus2" #define MICROPY_HW_MCU_NAME "STM32F405RG" #define MICROPY_HW_HAS_SWITCH (1) // On the netuino, the sdcard appears to be wired up as a 1-bit // SPI, so the driver needs to be converted to support that before // we can turn this on. #define MICROPY_HW_HAS_SDCARD (0) #define MICROPY_HW_HAS_MMA7660 (0) #define MICROPY_HW_HAS_LIS3DSH (0) #define MICROPY_HW_HAS_LCD (0) #define MICROPY_HW_ENABLE_RNG (1) #define MICROPY_HW_ENABLE_RTC (0) #define MICROPY_HW_ENABLE_TIMER (1) #define MICROPY_HW_ENABLE_SERVO (1) #define MICROPY_HW_ENABLE_DAC (0) #define MICROPY_HW_ENABLE_SPI1 (0) #define MICROPY_HW_ENABLE_SPI2 (1) #define MICROPY_HW_ENABLE_SPI3 (0) #define MICROPY_HW_ENABLE_CAN (0) // HSE is 25MHz #define MICROPY_HW_CLK_PLLM (25) #define MICROPY_HW_CLK_PLLN (336) #define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) #define MICROPY_HW_CLK_PLLQ (7) // UART config #define MICROPY_HW_UART1_PORT (GPIOA) #define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10) #define MICROPY_HW_UART2_PORT (GPIOA) #define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3) #define MICROPY_HW_UART2_RTS (GPIO_PIN_1) #define MICROPY_HW_UART2_CTS (GPIO_PIN_0) #define MICROPY_HW_UART3_PORT (GPIOD) #define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9) #define MICROPY_HW_UART3_RTS (GPIO_PIN_12) #define MICROPY_HW_UART3_CTS (GPIO_PIN_11) #define MICROPY_HW_UART4_PORT (GPIOA) #define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1) #define MICROPY_HW_UART6_PORT (GPIOC) #define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7) // I2C busses #define MICROPY_HW_I2C2_SCL (pin_B10) #define MICROPY_HW_I2C2_SDA (pin_B11) // USRSW is pulled low. Pressing the button makes the input go high. #define MICROPY_HW_USRSW_PIN (pin_B11) #define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) #define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) #define MICROPY_HW_USRSW_PRESSED (1) // LEDs #define MICROPY_HW_LED1 (pin_A10) // Blue LED #define MICROPY_HW_LED2 (pin_C13) // White LED (aka Power) #define MICROPY_HW_LED3 (pin_A10) // Same as Led(1) #define MICROPY_HW_LED4 (pin_C13) // Same as Led(2) #define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) #define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) #define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) // USB VBUS detect pin #define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)