//***************************************************************************** // //! \file w5500.h //! \brief W5500 HAL Header File. //! \version 1.0.0 //! \date 2013/10/21 //! \par Revision history //! <2013/10/21> 1st Release //! \author MidnightCow //! \copyright //! //! Copyright (c) 2013, WIZnet Co., LTD. //! All rights reserved. //! //! Redistribution and use in source and binary forms, with or without //! modification, are permitted provided that the following conditions //! are met: //! //! * Redistributions of source code must retain the above copyright //! notice, this list of conditions and the following disclaimer. //! * Redistributions in binary form must reproduce the above copyright //! notice, this list of conditions and the following disclaimer in the //! documentation and/or other materials provided with the distribution. //! * Neither the name of the nor the names of its //! contributors may be used to endorse or promote products derived //! from this software without specific prior written permission. //! //! THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" //! AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE //! IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE //! ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE //! LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR //! CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF //! SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS //! INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN //! CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) //! ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF //! THE POSSIBILITY OF SUCH DAMAGE. // //***************************************************************************** #ifndef _W5500_H_ #define _W5500_H_ #include #include "../wizchip_conf.h" #include "board.h" #define _W5500_IO_BASE_ 0x00000000 #define _W5500_SPI_READ_ (0x00 << 2) //< SPI interface Read operation in Control Phase #define _W5500_SPI_WRITE_ (0x01 << 2) //< SPI interface Write operation in Control Phase #define WIZCHIP_CREG_BLOCK 0x00 //< Common register block #define WIZCHIP_SREG_BLOCK(N) (1+4*N) //< Socket N register block #define WIZCHIP_TXBUF_BLOCK(N) (2+4*N) //< Socket N Tx buffer address block #define WIZCHIP_RXBUF_BLOCK(N) (3+4*N) //< Socket N Rx buffer address block #define WIZCHIP_OFFSET_INC(ADDR, N) (ADDR + (N<<8)) //< Increase offset address /////////////////////////////////////// // Definition For Legacy Chip Driver // /////////////////////////////////////// #define IINCHIP_READ(ADDR) WIZCHIP_READ(ADDR) ///< The defined for legacy chip driver #define IINCHIP_WRITE(ADDR,VAL) WIZCHIP_WRITE(ADDR,VAL) ///< The defined for legacy chip driver #define IINCHIP_READ_BUF(ADDR,BUF,LEN) WIZCHIP_READ_BUF(ADDR,BUF,LEN) ///< The defined for legacy chip driver #define IINCHIP_WRITE_BUF(ADDR,BUF,LEN) WIZCHIP_WRITE(ADDR,BUF,LEN) ///< The defined for legacy chip driver ////////////////////////////// //-------------------------- defgroup --------------------------------- /** * @defgroup W5500 W5500 * * @brief WHIZCHIP register defines and I/O functions of @b W5500. * * - @ref WIZCHIP_register : @ref Common_register_group and @ref Socket_register_group * - @ref WIZCHIP_IO_Functions : @ref Basic_IO_function, @ref Common_register_access_function and @ref Socket_register_access_function */ /** * @defgroup WIZCHIP_register WIZCHIP register * @ingroup W5500 * * @brief WHIZCHIP register defines register group of @b W5500. * * - @ref Common_register_group : Common register group * - @ref Socket_register_group : \c SOCKET n register group */ /** * @defgroup WIZCHIP_IO_Functions WIZCHIP I/O functions * @ingroup W5500 * * @brief This supports the basic I/O functions for @ref WIZCHIP_register. * * - Basic I/O function \n * WIZCHIP_READ(), WIZCHIP_WRITE(), WIZCHIP_READ_BUF(), WIZCHIP_WRITE_BUF() \n\n * * - @ref Common_register_group access functions \n * -# @b Mode \n * getMR(), setMR() * -# @b Interrupt \n * getIR(), setIR(), getIMR(), setIMR(), getSIR(), setSIR(), getSIMR(), setSIMR(), getINTLEVEL(), setINTLEVEL() * -# Network Information \n * getSHAR(), setSHAR(), getGAR(), setGAR(), getSUBR(), setSUBR(), getSIPR(), setSIPR() * -# @b Retransmission \n * getRCR(), setRCR(), getRTR(), setRTR() * -# @b PPPoE \n * getPTIMER(), setPTIMER(), getPMAGIC(), getPMAGIC(), getPSID(), setPSID(), getPHAR(), setPHAR(), getPMRU(), setPMRU() * -# ICMP packet \n * getUIPR(), getUPORTR() * -# @b etc. \n * getPHYCFGR(), setPHYCFGR(), getVERSIONR() \n\n * * - \ref Socket_register_group access functions \n * -# SOCKET control \n * getSn_MR(), setSn_MR(), getSn_CR(), setSn_CR(), getSn_IMR(), setSn_IMR(), getSn_IR(), setSn_IR() * -# SOCKET information \n * getSn_SR(), getSn_DHAR(), setSn_DHAR(), getSn_PORT(), setSn_PORT(), getSn_DIPR(), setSn_DIPR(), getSn_DPORT(), setSn_DPORT() * getSn_MSSR(), setSn_MSSR() * -# SOCKET communication \n * getSn_RXBUF_SIZE(), setSn_RXBUF_SIZE(), getSn_TXBUF_SIZE(), setSn_TXBUF_SIZE() \n * getSn_TX_RD(), getSn_TX_WR(), setSn_TX_WR() \n * getSn_RX_RD(), setSn_RX_RD(), getSn_RX_WR() \n * getSn_TX_FSR(), getSn_RX_RSR(), getSn_KPALVTR(), setSn_KPALVTR() * -# IP header field \n * getSn_FRAG(), setSn_FRAG(), getSn_TOS(), setSn_TOS() \n * getSn_TTL(), setSn_TTL() */ /** * @defgroup Common_register_group Common register * @ingroup WIZCHIP_register * * @brief Common register group\n * It set the basic for the networking\n * It set the configuration such as interrupt, network information, ICMP, etc. * @details * @sa MR : Mode register. * @sa GAR, SUBR, SHAR, SIPR * @sa INTLEVEL, IR, IMR, SIR, SIMR : Interrupt. * @sa RTR, RCR : Data retransmission. * @sa PTIMER, PMAGIC, PHAR, PSID, PMRU : PPPoE. * @sa UIPR, UPORTR : ICMP message. * @sa PHYCFGR, VERSIONR : etc. */ /** * @defgroup Socket_register_group Socket register * @ingroup WIZCHIP_register * * @brief Socket register group.\n * Socket register configures and control SOCKETn which is necessary to data communication. * @details * @sa Sn_MR, Sn_CR, Sn_IR, Sn_IMR : SOCKETn Control * @sa Sn_SR, Sn_PORT, Sn_DHAR, Sn_DIPR, Sn_DPORT : SOCKETn Information * @sa Sn_MSSR, Sn_TOS, Sn_TTL, Sn_KPALVTR, Sn_FRAG : Internet protocol. * @sa Sn_RXBUF_SIZE, Sn_TXBUF_SIZE, Sn_TX_FSR, Sn_TX_RD, Sn_TX_WR, Sn_RX_RSR, Sn_RX_RD, Sn_RX_WR : Data communication */ /** * @defgroup Basic_IO_function Basic I/O function * @ingroup WIZCHIP_IO_Functions * @brief These are basic input/output functions to read values from register or write values to register. */ /** * @defgroup Common_register_access_function Common register access functions * @ingroup WIZCHIP_IO_Functions * @brief These are functions to access common registers. */ /** * @defgroup Socket_register_access_function Socket register access functions * @ingroup WIZCHIP_IO_Functions * @brief These are functions to access socket registers. */ //------------------------------- defgroup end -------------------------------------------- //----------------------------- W5500 Common Registers IOMAP ----------------------------- /** * @ingroup Common_register_group * @brief Mode Register address(R/W)\n * @ref MR is used for S/W reset, ping block mode, PPPoE mode and etc. * @details Each bit of @ref MR defined as follows. * * * *
7 6 5 4 3 2 1 0
RST Reserved WOL PB PPPoE Reserved FARP Reserved
* - \ref MR_RST : Reset * - \ref MR_WOL : Wake on LAN * - \ref MR_PB : Ping block * - \ref MR_PPPOE : PPPoE mode * - \ref MR_FARP : Force ARP mode */ #define MR (_W5500_IO_BASE_ + (0x0000 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Gateway IP Register address(R/W) * @details @ref GAR configures the default gateway address. */ #define GAR (_W5500_IO_BASE_ + (0x0001 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Subnet mask Register address(R/W) * @details @ref SUBR configures the subnet mask address. */ #define SUBR (_W5500_IO_BASE_ + (0x0005 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Source MAC Register address(R/W) * @details @ref SHAR configures the source hardware address. */ #define SHAR (_W5500_IO_BASE_ + (0x0009 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Source IP Register address(R/W) * @details @ref SIPR configures the source IP address. */ #define SIPR (_W5500_IO_BASE_ + (0x000F << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Set Interrupt low level timer register address(R/W) * @details @ref INTLEVEL configures the Interrupt Assert Time. */ #define INTLEVEL (_W5500_IO_BASE_ + (0x0013 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Interrupt Register(R/W) * @details @ref IR indicates the interrupt status. Each bit of @ref IR will be still until the bit will be written to by the host. * If @ref IR is not equal to x00 INTn PIN is asserted to low until it is x00\n\n * Each bit of @ref IR defined as follows. * * * *
7 6 5 4 3 2 1 0
CONFLICT UNREACH PPPoE MP Reserved Reserved Reserved Reserved
* - \ref IR_CONFLICT : IP conflict * - \ref IR_UNREACH : Destination unreachable * - \ref IR_PPPoE : PPPoE connection close * - \ref IR_MP : Magic packet */ #define IR (_W5500_IO_BASE_ + (0x0015 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Interrupt mask register(R/W) * @details @ref IMR is used to mask interrupts. Each bit of @ref IMR corresponds to each bit of @ref IR. * When a bit of @ref IMR is and the corresponding bit of @ref IR is an interrupt will be issued. In other words, * if a bit of @ref IMR is an interrupt will not be issued even if the corresponding bit of @ref IR is \n\n * Each bit of @ref IMR defined as the following. * * * *
7 6 5 4 3 2 1 0
IM_IR7 IM_IR6 IM_IR5 IM_IR4 Reserved Reserved Reserved Reserved
* - \ref IM_IR7 : IP Conflict Interrupt Mask * - \ref IM_IR6 : Destination unreachable Interrupt Mask * - \ref IM_IR5 : PPPoE Close Interrupt Mask * - \ref IM_IR4 : Magic Packet Interrupt Mask */ #define IMR (_W5500_IO_BASE_ + (0x0016 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Socket Interrupt Register(R/W) * @details @ref SIR indicates the interrupt status of Socket.\n * Each bit of @ref SIR be still until @ref Sn_IR is cleared by the host.\n * If @ref Sn_IR is not equal to x00 the n-th bit of @ref SIR is and INTn PIN is asserted until @ref SIR is x00 */ #define SIR (_W5500_IO_BASE_ + (0x0017 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Socket Interrupt Mask Register(R/W) * @details Each bit of @ref SIMR corresponds to each bit of @ref SIR. * When a bit of @ref SIMR is and the corresponding bit of @ref SIR is Interrupt will be issued. * In other words, if a bit of @ref SIMR is an interrupt will be not issued even if the corresponding bit of @ref SIR is */ #define SIMR (_W5500_IO_BASE_ + (0x0018 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Timeout register address( 1 is 100us )(R/W) * @details @ref RTR configures the retransmission timeout period. The unit of timeout period is 100us and the default of @ref RTR is x07D0or 000 * And so the default timeout period is 200ms(100us X 2000). During the time configured by @ref RTR, W5500 waits for the peer response * to the packet that is transmitted by \ref Sn_CR (CONNECT, DISCON, CLOSE, SEND, SEND_MAC, SEND_KEEP command). * If the peer does not respond within the @ref RTR time, W5500 retransmits the packet or issues timeout. */ #define RTR (_W5500_IO_BASE_ + (0x0019 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Retry count register(R/W) * @details @ref RCR configures the number of time of retransmission. * When retransmission occurs as many as ref RCR+1 Timeout interrupt is issued (@ref Sn_IR[TIMEOUT] = . */ #define RCR (_W5500_IO_BASE_ + (0x001B << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PPP LCP Request Timer register in PPPoE mode(R/W) * @details @ref PTIMER configures the time for sending LCP echo request. The unit of time is 25ms. */ #define PTIMER (_W5500_IO_BASE_ + (0x001C << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PPP LCP Magic number register in PPPoE mode(R/W) * @details @ref PMAGIC configures the 4bytes magic number to be used in LCP negotiation. */ #define PMAGIC (_W5500_IO_BASE_ + (0x001D << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PPP Destination MAC Register address(R/W) * @details @ref PHAR configures the PPPoE server hardware address that is acquired during PPPoE connection process. */ #define PHAR (_W5500_IO_BASE_ + (0x001E << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PPP Session Identification Register(R/W) * @details @ref PSID configures the PPPoE sever session ID acquired during PPPoE connection process. */ #define PSID (_W5500_IO_BASE_ + (0x0024 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PPP Maximum Segment Size(MSS) register(R/W) * @details @ref PMRU configures the maximum receive unit of PPPoE. */ #define PMRU (_W5500_IO_BASE_ + (0x0026 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Unreachable IP register address in UDP mode(R) * @details W5500 receives an ICMP packet(Destination port unreachable) when data is sent to a port number * which socket is not open and @ref UNREACH bit of @ref IR becomes and @ref UIPR & @ref UPORTR indicates * the destination IP address & port number respectively. */ #define UIPR (_W5500_IO_BASE_ + (0x0028 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief Unreachable Port register address in UDP mode(R) * @details W5500 receives an ICMP packet(Destination port unreachable) when data is sent to a port number * which socket is not open and @ref UNREACH bit of @ref IR becomes and @ref UIPR & @ref UPORTR * indicates the destination IP address & port number respectively. */ #define UPORTR (_W5500_IO_BASE_ + (0x002C << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief PHY Status Register(R/W) * @details @ref PHYCFGR configures PHY operation mode and resets PHY. In addition, @ref PHYCFGR indicates the status of PHY such as duplex, Speed, Link. */ #define PHYCFGR (_W5500_IO_BASE_ + (0x002E << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x002F << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0030 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0031 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0032 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0033 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0034 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0035 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0036 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0037 << 8) + (WIZCHIP_CREG_BLOCK << 3)) // Reserved (_W5500_IO_BASE_ + (0x0038 << 8) + (WIZCHIP_CREG_BLOCK << 3)) /** * @ingroup Common_register_group * @brief chip version register address(R) * @details @ref VERSIONR always indicates the W5500 version as @b 0x04. */ #define VERSIONR (_W5500_IO_BASE_ + (0x0039 << 8) + (WIZCHIP_CREG_BLOCK << 3)) //----------------------------- W5500 Socket Registers IOMAP ----------------------------- /** * @ingroup Socket_register_group * @brief socket Mode register(R/W) * @details @ref Sn_MR configures the option or protocol type of Socket n.\n\n * Each bit of @ref Sn_MR defined as the following. * * * *
7 6 5 4 3 2 1 0
MULTI/MFEN BCASTB ND/MC/MMB UCASTB/MIP6B Protocol[3] Protocol[2] Protocol[1] Protocol[0]
* - @ref Sn_MR_MULTI : Support UDP Multicasting * - @ref Sn_MR_BCASTB : Broadcast block in UDP Multicasting * - @ref Sn_MR_ND : No Delayed Ack(TCP) flag * - @ref Sn_MR_MC : IGMP version used in UDP mulitcasting * - @ref Sn_MR_MMB : Multicast Blocking in @ref Sn_MR_MACRAW mode * - @ref Sn_MR_UCASTB : Unicast Block in UDP Multicating * - @ref Sn_MR_MIP6B : IPv6 packet Blocking in @ref Sn_MR_MACRAW mode * - Protocol * * * * * * *
Protocol[3] Protocol[2] Protocol[1] Protocol[0] @b Meaning
0 0 0 0 Closed
0 0 0 1 TCP
0 0 1 0 UDP
0 1 0 0 MACRAW
* - @ref Sn_MR_MACRAW : MAC LAYER RAW SOCK \n * - @ref Sn_MR_UDP : UDP * - @ref Sn_MR_TCP : TCP * - @ref Sn_MR_CLOSE : Unused socket * @note MACRAW mode should be only used in Socket 0. */ #define Sn_MR(N) (_W5500_IO_BASE_ + (0x0000 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Socket command register(R/W) * @details This is used to set the command for Socket n such as OPEN, CLOSE, CONNECT, LISTEN, SEND, and RECEIVE.\n * After W5500 accepts the command, the @ref Sn_CR register is automatically cleared to 0x00. * Even though @ref Sn_CR is cleared to 0x00, the command is still being processed.\n * To check whether the command is completed or not, please check the @ref Sn_IR or @ref Sn_SR. * - @ref Sn_CR_OPEN : Initialize or open socket. * - @ref Sn_CR_LISTEN : Wait connection request in TCP mode(Server mode) * - @ref Sn_CR_CONNECT : Send connection request in TCP mode(Client mode) * - @ref Sn_CR_DISCON : Send closing request in TCP mode. * - @ref Sn_CR_CLOSE : Close socket. * - @ref Sn_CR_SEND : Update TX buffer pointer and send data. * - @ref Sn_CR_SEND_MAC : Send data with MAC address, so without ARP process. * - @ref Sn_CR_SEND_KEEP : Send keep alive message. * - @ref Sn_CR_RECV : Update RX buffer pointer and receive data. */ #define Sn_CR(N) (_W5500_IO_BASE_ + (0x0001 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Socket interrupt register(R) * @details @ref Sn_IR indicates the status of Socket Interrupt such as establishment, termination, receiving data, timeout).\n * When an interrupt occurs and the corresponding bit of @ref Sn_IMR is the corresponding bit of @ref Sn_IR becomes \n * In order to clear the @ref Sn_IR bit, the host should write the bit to \n * * * *
7 6 5 4 3 2 1 0
Reserved Reserved Reserved SEND_OK TIMEOUT RECV DISCON CON
* - \ref Sn_IR_SENDOK : SEND_OK Interrupt * - \ref Sn_IR_TIMEOUT : TIMEOUT Interrupt * - \ref Sn_IR_RECV : RECV Interrupt * - \ref Sn_IR_DISCON : DISCON Interrupt * - \ref Sn_IR_CON : CON Interrupt */ #define Sn_IR(N) (_W5500_IO_BASE_ + (0x0002 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Socket status register(R) * @details @ref Sn_SR indicates the status of Socket n.\n * The status of Socket n is changed by @ref Sn_CR or some special control packet as SYN, FIN packet in TCP. * @par Normal status * - @ref SOCK_CLOSED : Closed * - @ref SOCK_INIT : Initiate state * - @ref SOCK_LISTEN : Listen state * - @ref SOCK_ESTABLISHED : Success to connect * - @ref SOCK_CLOSE_WAIT : Closing state * - @ref SOCK_UDP : UDP socket * - @ref SOCK_MACRAW : MAC raw mode socket *@par Temporary status during changing the status of Socket n. * - @ref SOCK_SYNSENT : This indicates Socket n sent the connect-request packet (SYN packet) to a peer. * - @ref SOCK_SYNRECV : It indicates Socket n successfully received the connect-request packet (SYN packet) from a peer. * - @ref SOCK_FIN_WAIT : Connection state * - @ref SOCK_CLOSING : Closing state * - @ref SOCK_TIME_WAIT : Closing state * - @ref SOCK_LAST_ACK : Closing state */ #define Sn_SR(N) (_W5500_IO_BASE_ + (0x0003 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief source port register(R/W) * @details @ref Sn_PORT configures the source port number of Socket n. * It is valid when Socket n is used in TCP/UPD mode. It should be set before OPEN command is ordered. */ #define Sn_PORT(N) (_W5500_IO_BASE_ + (0x0004 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Peer MAC register address(R/W) * @details @ref Sn_DHAR configures the destination hardware address of Socket n when using SEND_MAC command in UDP mode or * it indicates that it is acquired in ARP-process by CONNECT/SEND command. */ #define Sn_DHAR(N) (_W5500_IO_BASE_ + (0x0006 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Peer IP register address(R/W) * @details @ref Sn_DIPR configures or indicates the destination IP address of Socket n. It is valid when Socket n is used in TCP/UDP mode. * In TCP client mode, it configures an IP address of �TCP serverbefore CONNECT command. * In TCP server mode, it indicates an IP address of �TCP clientafter successfully establishing connection. * In UDP mode, it configures an IP address of peer to be received the UDP packet by SEND or SEND_MAC command. */ #define Sn_DIPR(N) (_W5500_IO_BASE_ + (0x000C << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Peer port register address(R/W) * @details @ref Sn_DPORT configures or indicates the destination port number of Socket n. It is valid when Socket n is used in TCP/UDP mode. * In �TCP clientmode, it configures the listen port number of �TCP serverbefore CONNECT command. * In �TCP Servermode, it indicates the port number of TCP client after successfully establishing connection. * In UDP mode, it configures the port number of peer to be transmitted the UDP packet by SEND/SEND_MAC command. */ #define Sn_DPORT(N) (_W5500_IO_BASE_ + (0x0010 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Maximum Segment Size(Sn_MSSR0) register address(R/W) * @details @ref Sn_MSSR configures or indicates the MTU(Maximum Transfer Unit) of Socket n. */ #define Sn_MSSR(N) (_W5500_IO_BASE_ + (0x0012 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x0014 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief IP Type of Service(TOS) Register(R/W) * @details @ref Sn_TOS configures the TOS(Type Of Service field in IP Header) of Socket n. * It is set before OPEN command. */ #define Sn_TOS(N) (_W5500_IO_BASE_ + (0x0015 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief IP Time to live(TTL) Register(R/W) * @details @ref Sn_TTL configures the TTL(Time To Live field in IP header) of Socket n. * It is set before OPEN command. */ #define Sn_TTL(N) (_W5500_IO_BASE_ + (0x0016 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x0017 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x0018 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x0019 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x001A << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x001B << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x001C << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) // Reserved (_W5500_IO_BASE_ + (0x001D << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Receive memory size register(R/W) * @details @ref Sn_RXBUF_SIZE configures the RX buffer block size of Socket n. * Socket n RX Buffer Block size can be configured with 1,2,4,8, and 16 Kbytes. * If a different size is configured, the data cannot be normally received from a peer. * Although Socket n RX Buffer Block size is initially configured to 2Kbytes, * user can re-configure its size using @ref Sn_RXBUF_SIZE. The total sum of @ref Sn_RXBUF_SIZE can not be exceed 16Kbytes. * When exceeded, the data reception error is occurred. */ #define Sn_RXBUF_SIZE(N) (_W5500_IO_BASE_ + (0x001E << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Transmit memory size register(R/W) * @details @ref Sn_TXBUF_SIZE configures the TX buffer block size of Socket n. Socket n TX Buffer Block size can be configured with 1,2,4,8, and 16 Kbytes. * If a different size is configured, the data can�t be normally transmitted to a peer. * Although Socket n TX Buffer Block size is initially configured to 2Kbytes, * user can be re-configure its size using @ref Sn_TXBUF_SIZE. The total sum of @ref Sn_TXBUF_SIZE can not be exceed 16Kbytes. * When exceeded, the data transmission error is occurred. */ #define Sn_TXBUF_SIZE(N) (_W5500_IO_BASE_ + (0x001F << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Transmit free memory size register(R) * @details @ref Sn_TX_FSR indicates the free size of Socket n TX Buffer Block. It is initialized to the configured size by @ref Sn_TXBUF_SIZE. * Data bigger than @ref Sn_TX_FSR should not be saved in the Socket n TX Buffer because the bigger data overwrites the previous saved data not yet sent. * Therefore, check before saving the data to the Socket n TX Buffer, and if data is equal or smaller than its checked size, * transmit the data with SEND/SEND_MAC command after saving the data in Socket n TX buffer. But, if data is bigger than its checked size, * transmit the data after dividing into the checked size and saving in the Socket n TX buffer. */ #define Sn_TX_FSR(N) (_W5500_IO_BASE_ + (0x0020 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Transmit memory read pointer register address(R) * @details @ref Sn_TX_RD is initialized by OPEN command. However, if Sn_MR(P[3:0]) is TCP mode(001, it is re-initialized while connecting with TCP. * After its initialization, it is auto-increased by SEND command. * SEND command transmits the saved data from the current @ref Sn_TX_RD to the @ref Sn_TX_WR in the Socket n TX Buffer. * After transmitting the saved data, the SEND command increases the @ref Sn_TX_RD as same as the @ref Sn_TX_WR. * If its increment value exceeds the maximum value 0xFFFF, (greater than 0x10000 and the carry bit occurs), * then the carry bit is ignored and will automatically update with the lower 16bits value. */ #define Sn_TX_RD(N) (_W5500_IO_BASE_ + (0x0022 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Transmit memory write pointer register address(R/W) * @details @ref Sn_TX_WR is initialized by OPEN command. However, if Sn_MR(P[3:0]) is TCP mode(001, it is re-initialized while connecting with TCP.\n * It should be read or be updated like as follows.\n * 1. Read the starting address for saving the transmitting data.\n * 2. Save the transmitting data from the starting address of Socket n TX buffer.\n * 3. After saving the transmitting data, update @ref Sn_TX_WR to the increased value as many as transmitting data size. * If the increment value exceeds the maximum value 0xFFFF(greater than 0x10000 and the carry bit occurs), * then the carry bit is ignored and will automatically update with the lower 16bits value.\n * 4. Transmit the saved data in Socket n TX Buffer by using SEND/SEND command */ #define Sn_TX_WR(N) (_W5500_IO_BASE_ + (0x0024 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Received data size register(R) * @details @ref Sn_RX_RSR indicates the data size received and saved in Socket n RX Buffer. * @ref Sn_RX_RSR does not exceed the @ref Sn_RXBUF_SIZE and is calculated as the difference between * �Socket n RX Write Pointer (@ref Sn_RX_WR)and �Socket n RX Read Pointer (@ref Sn_RX_RD) */ #define Sn_RX_RSR(N) (_W5500_IO_BASE_ + (0x0026 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Read point of Receive memory(R/W) * @details @ref Sn_RX_RD is initialized by OPEN command. Make sure to be read or updated as follows.\n * 1. Read the starting save address of the received data.\n * 2. Read data from the starting address of Socket n RX Buffer.\n * 3. After reading the received data, Update @ref Sn_RX_RD to the increased value as many as the reading size. * If the increment value exceeds the maximum value 0xFFFF, that is, is greater than 0x10000 and the carry bit occurs, * update with the lower 16bits value ignored the carry bit.\n * 4. Order RECV command is for notifying the updated @ref Sn_RX_RD to W5500. */ #define Sn_RX_RD(N) (_W5500_IO_BASE_ + (0x0028 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Write point of Receive memory(R) * @details @ref Sn_RX_WR is initialized by OPEN command and it is auto-increased by the data reception. * If the increased value exceeds the maximum value 0xFFFF, (greater than 0x10000 and the carry bit occurs), * then the carry bit is ignored and will automatically update with the lower 16bits value. */ #define Sn_RX_WR(N) (_W5500_IO_BASE_ + (0x002A << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief socket interrupt mask register(R) * @details @ref Sn_IMR masks the interrupt of Socket n. * Each bit corresponds to each bit of @ref Sn_IR. When a Socket n Interrupt is occurred and the corresponding bit of @ref Sn_IMR is * the corresponding bit of @ref Sn_IR becomes When both the corresponding bit of @ref Sn_IMR and @ref Sn_IR are and the n-th bit of @ref IR is * Host is interrupted by asserted INTn PIN to low. */ #define Sn_IMR(N) (_W5500_IO_BASE_ + (0x002C << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Fragment field value in IP header register(R/W) * @details @ref Sn_FRAG configures the FRAG(Fragment field in IP header). */ #define Sn_FRAG(N) (_W5500_IO_BASE_ + (0x002D << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) /** * @ingroup Socket_register_group * @brief Keep Alive Timer register(R/W) * @details @ref Sn_KPALVTR configures the transmitting timer of �KEEP ALIVE(KA)packet of SOCKETn. It is valid only in TCP mode, * and ignored in other modes. The time unit is 5s. * KA packet is transmittable after @ref Sn_SR is changed to SOCK_ESTABLISHED and after the data is transmitted or received to/from a peer at least once. * In case of '@ref Sn_KPALVTR > 0', W5500 automatically transmits KA packet after time-period for checking the TCP connection (Auto-keepalive-process). * In case of '@ref Sn_KPALVTR = 0', Auto-keep-alive-process will not operate, * and KA packet can be transmitted by SEND_KEEP command by the host (Manual-keep-alive-process). * Manual-keep-alive-process is ignored in case of '@ref Sn_KPALVTR > 0'. */ #define Sn_KPALVTR(N) (_W5500_IO_BASE_ + (0x002F << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) //#define Sn_TSR(N) (_W5500_IO_BASE_ + (0x0030 << 8) + (WIZCHIP_SREG_BLOCK(N) << 3)) //----------------------------- W5500 Register values ----------------------------- /* MODE register values */ /** * @brief Reset * @details If this bit is All internal registers will be initialized. It will be automatically cleared as after S/W reset. */ #define MR_RST 0x80 /** * @brief Wake on LAN * @details 0 : Disable WOL mode\n * 1 : Enable WOL mode\n * If WOL mode is enabled and the received magic packet over UDP has been normally processed, the Interrupt PIN (INTn) asserts to low. * When using WOL mode, the UDP Socket should be opened with any source port number. (Refer to Socket n Mode Register (@ref Sn_MR) for opening Socket.) * @note The magic packet over UDP supported by W5500 consists of 6 bytes synchronization stream (xFFFFFFFFFFFF and * 16 times Target MAC address stream in UDP payload. The options such like password are ignored. You can use any UDP source port number for WOL mode. */ #define MR_WOL 0x20 /** * @brief Ping block * @details 0 : Disable Ping block\n * 1 : Enable Ping block\n * If the bit is it blocks the response to a ping request. */ #define MR_PB 0x10 /** * @brief Enable PPPoE * @details 0 : DisablePPPoE mode\n * 1 : EnablePPPoE mode\n * If you use ADSL, this bit should be */ #define MR_PPPOE 0x08 /** * @brief Enable UDP_FORCE_ARP CHECHK * @details 0 : Disable Force ARP mode\n * 1 : Enable Force ARP mode\n * In Force ARP mode, It forces on sending ARP Request whenever data is sent. */ #define MR_FARP 0x02 /* IR register values */ /** * @brief Check IP conflict. * @details Bit is set as when own source IP address is same with the sender IP address in the received ARP request. */ #define IR_CONFLICT 0x80 /** * @brief Get the destination unreachable message in UDP sending. * @details When receiving the ICMP (Destination port unreachable) packet, this bit is set as * When this bit is Destination Information such as IP address and Port number may be checked with the corresponding @ref UIPR & @ref UPORTR. */ #define IR_UNREACH 0x40 /** * @brief Get the PPPoE close message. * @details When PPPoE is disconnected during PPPoE mode, this bit is set. */ #define IR_PPPoE 0x20 /** * @brief Get the magic packet interrupt. * @details When WOL mode is enabled and receives the magic packet over UDP, this bit is set. */ #define IR_MP 0x10 /* PHYCFGR register value */ #define PHYCFGR_RST ~(1<<7) //< For PHY reset, must operate AND mask. #define PHYCFGR_OPMD (1<<6) // Configre PHY with OPMDC value #define PHYCFGR_OPMDC_ALLA (7<<3) #define PHYCFGR_OPMDC_PDOWN (6<<3) #define PHYCFGR_OPMDC_NA (5<<3) #define PHYCFGR_OPMDC_100FA (4<<3) #define PHYCFGR_OPMDC_100F (3<<3) #define PHYCFGR_OPMDC_100H (2<<3) #define PHYCFGR_OPMDC_10F (1<<3) #define PHYCFGR_OPMDC_10H (0<<3) #define PHYCFGR_DPX_FULL (1<<2) #define PHYCFGR_DPX_HALF (0<<2) #define PHYCFGR_SPD_100 (1<<1) #define PHYCFGR_SPD_10 (0<<1) #define PHYCFGR_LNK_ON (1<<0) #define PHYCFGR_LNK_OFF (0<<0) /* IMR register values */ /** * @brief IP Conflict Interrupt Mask. * @details 0: Disable IP Conflict Interrupt\n * 1: Enable IP Conflict Interrupt */ #define IM_IR7 0x80 /** * @brief Destination unreachable Interrupt Mask. * @details 0: Disable Destination unreachable Interrupt\n * 1: Enable Destination unreachable Interrupt */ #define IM_IR6 0x40 /** * @brief PPPoE Close Interrupt Mask. * @details 0: Disable PPPoE Close Interrupt\n * 1: Enable PPPoE Close Interrupt */ #define IM_IR5 0x20 /** * @brief Magic Packet Interrupt Mask. * @details 0: Disable Magic Packet Interrupt\n * 1: Enable Magic Packet Interrupt */ #define IM_IR4 0x10 /* Sn_MR Default values */ /** * @brief Support UDP Multicasting * @details 0 : disable Multicasting\n * 1 : enable Multicasting\n * This bit is applied only during UDP mode(P[3:0] = 010.\n * To use multicasting, @ref Sn_DIPR & @ref Sn_DPORT should be respectively configured with the multicast group IP address & port number * before Socket n is opened by OPEN command of @ref Sn_CR. */ #define Sn_MR_MULTI 0x80 /** * @brief Broadcast block in UDP Multicasting. * @details 0 : disable Broadcast Blocking\n * 1 : enable Broadcast Blocking\n * This bit blocks to receive broadcasting packet during UDP mode(P[3:0] = 010.\m * In addition, This bit does when MACRAW mode(P[3:0] = 100 */ #define Sn_MR_BCASTB 0x40 /** * @brief No Delayed Ack(TCP), Multicast flag * @details 0 : Disable No Delayed ACK option\n * 1 : Enable No Delayed ACK option\n * This bit is applied only during TCP mode (P[3:0] = 001.\n * When this bit is It sends the ACK packet without delay as soon as a Data packet is received from a peer.\n * When this bit is It sends the ACK packet after waiting for the timeout time configured by @ref RTR. */ #define Sn_MR_ND 0x20 /** * @brief Unicast Block in UDP Multicasting * @details 0 : disable Unicast Blocking\n * 1 : enable Unicast Blocking\n * This bit blocks receiving the unicast packet during UDP mode(P[3:0] = 010 and MULTI = */ #define Sn_MR_UCASTB 0x10 /** * @brief MAC LAYER RAW SOCK * @details This configures the protocol mode of Socket n. * @note MACRAW mode should be only used in Socket 0. */ #define Sn_MR_MACRAW 0x04 //#define Sn_MR_IPRAW 0x03 /**< IP LAYER RAW SOCK */ /** * @brief UDP * @details This configures the protocol mode of Socket n. */ #define Sn_MR_UDP 0x02 /** * @brief TCP * @details This configures the protocol mode of Socket n. */ #define Sn_MR_TCP 0x01 /** * @brief Unused socket * @details This configures the protocol mode of Socket n. */ #define Sn_MR_CLOSE 0x00 /* Sn_MR values used with Sn_MR_MACRAW */ /** * @brief MAC filter enable in @ref Sn_MR_MACRAW mode * @details 0 : disable MAC Filtering\n * 1 : enable MAC Filtering\n * This bit is applied only during MACRAW mode(P[3:0] = 100.\n * When set as W5500 can only receive broadcasting packet or packet sent to itself. * When this bit is W5500 can receive all packets on Ethernet. * If user wants to implement Hybrid TCP/IP stack, * it is recommended that this bit is set as for reducing host overhead to process the all received packets. */ #define Sn_MR_MFEN Sn_MR_MULTI /** * @brief Multicast Blocking in @ref Sn_MR_MACRAW mode * @details 0 : using IGMP version 2\n * 1 : using IGMP version 1\n * This bit is applied only during UDP mode(P[3:0] = 010 and MULTI = * It configures the version for IGMP messages (Join/Leave/Report). */ #define Sn_MR_MMB Sn_MR_ND /** * @brief IPv6 packet Blocking in @ref Sn_MR_MACRAW mode * @details 0 : disable IPv6 Blocking\n * 1 : enable IPv6 Blocking\n * This bit is applied only during MACRAW mode (P[3:0] = 100. It blocks to receiving the IPv6 packet. */ #define Sn_MR_MIP6B Sn_MR_UCASTB /* Sn_MR value used with Sn_MR_UDP & Sn_MR_MULTI */ /** * @brief IGMP version used in UDP mulitcasting * @details 0 : disable Multicast Blocking\n * 1 : enable Multicast Blocking\n * This bit is applied only when MACRAW mode(P[3:0] = 100. It blocks to receive the packet with multicast MAC address. */ #define Sn_MR_MC Sn_MR_ND /* Sn_MR alternate values */ /** * @brief For Berkeley Socket API */ #define SOCK_STREAM Sn_MR_TCP /** * @brief For Berkeley Socket API */ #define SOCK_DGRAM Sn_MR_UDP /* Sn_CR values */ /** * @brief Initialize or open socket * @details Socket n is initialized and opened according to the protocol selected in Sn_MR(P3:P0). * The table below shows the value of @ref Sn_SR corresponding to @ref Sn_MR.\n * * * * * * *
\b Sn_MR (P[3:0]) \b Sn_SR
Sn_MR_CLOSE (000
Sn_MR_TCP (001 SOCK_INIT (0x13)
Sn_MR_UDP (010 SOCK_UDP (0x22)
S0_MR_MACRAW (100 SOCK_MACRAW (0x02)
*/ #define Sn_CR_OPEN 0x01 /** * @brief Wait connection request in TCP mode(Server mode) * @details This is valid only in TCP mode (Sn_MR(P3:P0) = Sn_MR_TCP). * In this mode, Socket n operates as a �TCP serverand waits for connection-request (SYN packet) from any �TCP client * The @ref Sn_SR changes the state from SOCK_INIT to SOCKET_LISTEN. * When a �TCP clientconnection request is successfully established, * the @ref Sn_SR changes from SOCK_LISTEN to SOCK_ESTABLISHED and the Sn_IR(0) becomes * But when a �TCP clientconnection request is failed, Sn_IR(3) becomes and the status of @ref Sn_SR changes to SOCK_CLOSED. */ #define Sn_CR_LISTEN 0x02 /** * @brief Send connection request in TCP mode(Client mode) * @details To connect, a connect-request (SYN packet) is sent to b>TCP serverconfigured by @ref Sn_DIPR & Sn_DPORT(destination address & port). * If the connect-request is successful, the @ref Sn_SR is changed to @ref SOCK_ESTABLISHED and the Sn_IR(0) becomes \n\n * The connect-request fails in the following three cases.\n * 1. When a @b ARPTO occurs (@ref Sn_IR[3] = ) because destination hardware address is not acquired through the ARP-process.\n * 2. When a @b SYN/ACK packet is not received and @b TCPTO (Sn_IR(3) = )\n * 3. When a @b RST packet is received instead of a @b SYN/ACK packet. In these cases, @ref Sn_SR is changed to @ref SOCK_CLOSED. * @note This is valid only in TCP mode and operates when Socket n acts as b>TCP client */ #define Sn_CR_CONNECT 0x04 /** * @brief Send closing request in TCP mode * @details Regardless of b>TCP serveror b>TCP client the DISCON command processes the disconnect-process (b>Active closeor b>Passive close.\n * @par Active close * it transmits disconnect-request(FIN packet) to the connected peer\n * @par Passive close * When FIN packet is received from peer, a FIN packet is replied back to the peer.\n * @details When the disconnect-process is successful (that is, FIN/ACK packet is received successfully), @ref Sn_SR is changed to @ref SOCK_CLOSED.\n * Otherwise, TCPTO occurs (Sn_IR(3)=)= and then @ref Sn_SR is changed to @ref SOCK_CLOSED. * @note Valid only in TCP mode. */ #define Sn_CR_DISCON 0x08 /** * @brief Close socket * @details Sn_SR is changed to @ref SOCK_CLOSED. */ #define Sn_CR_CLOSE 0x10 /** * @brief Update TX buffer pointer and send data * @details SEND transmits all the data in the Socket n TX buffer.\n * For more details, please refer to Socket n TX Free Size Register (@ref Sn_TX_FSR), Socket n, * TX Write Pointer Register(@ref Sn_TX_WR), and Socket n TX Read Pointer Register(@ref Sn_TX_RD). */ #define Sn_CR_SEND 0x20 /** * @brief Send data with MAC address, so without ARP process * @details The basic operation is same as SEND.\n * Normally SEND transmits data after destination hardware address is acquired by the automatic ARP-process(Address Resolution Protocol).\n * But SEND_MAC transmits data without the automatic ARP-process.\n * In this case, the destination hardware address is acquired from @ref Sn_DHAR configured by host, instead of APR-process. * @note Valid only in UDP mode. */ #define Sn_CR_SEND_MAC 0x21 /** * @brief Send keep alive message * @details It checks the connection status by sending 1byte keep-alive packet.\n * If the peer can not respond to the keep-alive packet during timeout time, the connection is terminated and the timeout interrupt will occur. * @note Valid only in TCP mode. */ #define Sn_CR_SEND_KEEP 0x22 /** * @brief Update RX buffer pointer and receive data * @details RECV completes the processing of the received data in Socket n RX Buffer by using a RX read pointer register (@ref Sn_RX_RD).\n * For more details, refer to Socket n RX Received Size Register (@ref Sn_RX_RSR), Socket n RX Write Pointer Register (@ref Sn_RX_WR), * and Socket n RX Read Pointer Register (@ref Sn_RX_RD). */ #define Sn_CR_RECV 0x40 /* Sn_IR values */ /** * @brief SEND_OK Interrupt * @details This is issued when SEND command is completed. */ #define Sn_IR_SENDOK 0x10 /** * @brief TIMEOUT Interrupt * @details This is issued when ARPTO or TCPTO occurs. */ #define Sn_IR_TIMEOUT 0x08 /** * @brief RECV Interrupt * @details This is issued whenever data is received from a peer. */ #define Sn_IR_RECV 0x04 /** * @brief DISCON Interrupt * @details This is issued when FIN or FIN/ACK packet is received from a peer. */ #define Sn_IR_DISCON 0x02 /** * @brief CON Interrupt * @details This is issued one time when the connection with peer is successful and then @ref Sn_SR is changed to @ref SOCK_ESTABLISHED. */ #define Sn_IR_CON 0x01 /* Sn_SR values */ /** * @brief Closed * @details This indicates that Socket n is released.\N * When DICON, CLOSE command is ordered, or when a timeout occurs, it is changed to @ref SOCK_CLOSED regardless of previous status. */ #define SOCK_CLOSED 0x00 /** * @brief Initiate state * @details This indicates Socket n is opened with TCP mode.\N * It is changed to @ref SOCK_INIT when Sn_MR(P[3:0]) = 001and OPEN command is ordered.\N * After @ref SOCK_INIT, user can use LISTEN /CONNECT command. */ #define SOCK_INIT 0x13 /** * @brief Listen state * @details This indicates Socket n is operating as b>TCP servermode and waiting for connection-request (SYN packet) from a peer (b>TCP client.\n * It will change to @ref SOCK_ESTALBLISHED when the connection-request is successfully accepted.\n * Otherwise it will change to @ref SOCK_CLOSED after TCPTO occurred (Sn_IR(TIMEOUT) = . */ #define SOCK_LISTEN 0x14 /** * @brief Connection state * @details This indicates Socket n sent the connect-request packet (SYN packet) to a peer.\n * It is temporarily shown when @ref Sn_SR is changed from @ref SOCK_INIT to @ref SOCK_ESTABLISHED by CONNECT command.\n * If connect-accept(SYN/ACK packet) is received from the peer at SOCK_SYNSENT, it changes to @ref SOCK_ESTABLISHED.\n * Otherwise, it changes to @ref SOCK_CLOSED after TCPTO (@ref Sn_IR[TIMEOUT] = is occurred. */ #define SOCK_SYNSENT 0x15 /** * @brief Connection state * @details It indicates Socket n successfully received the connect-request packet (SYN packet) from a peer.\n * If socket n sends the response (SYN/ACK packet) to the peer successfully, it changes to @ref SOCK_ESTABLISHED. \n * If not, it changes to @ref SOCK_CLOSED after timeout occurs (@ref Sn_IR[TIMEOUT] = . */ #define SOCK_SYNRECV 0x16 /** * @brief Success to connect * @details This indicates the status of the connection of Socket n.\n * It changes to @ref SOCK_ESTABLISHED when the b>TCP SERVERprocessed the SYN packet from the b>TCP CLIENTduring @ref SOCK_LISTEN, or * when the CONNECT command is successful.\n * During @ref SOCK_ESTABLISHED, DATA packet can be transferred using SEND or RECV command. */ #define SOCK_ESTABLISHED 0x17 /** * @brief Closing state * @details These indicate Socket n is closing.\n * These are shown in disconnect-process such as active-close and passive-close.\n * When Disconnect-process is successfully completed, or when timeout occurs, these change to @ref SOCK_CLOSED. */ #define SOCK_FIN_WAIT 0x18 /** * @brief Closing state * @details These indicate Socket n is closing.\n * These are shown in disconnect-process such as active-close and passive-close.\n * When Disconnect-process is successfully completed, or when timeout occurs, these change to @ref SOCK_CLOSED. */ #define SOCK_CLOSING 0x1A /** * @brief Closing state * @details These indicate Socket n is closing.\n * These are shown in disconnect-process such as active-close and passive-close.\n * When Disconnect-process is successfully completed, or when timeout occurs, these change to @ref SOCK_CLOSED. */ #define SOCK_TIME_WAIT 0x1B /** * @brief Closing state * @details This indicates Socket n received the disconnect-request (FIN packet) from the connected peer.\n * This is half-closing status, and data can be transferred.\n * For full-closing, DISCON command is used. But For just-closing, CLOSE command is used. */ #define SOCK_CLOSE_WAIT 0x1C /** * @brief Closing state * @details This indicates Socket n is waiting for the response (FIN/ACK packet) to the disconnect-request (FIN packet) by passive-close.\n * It changes to @ref SOCK_CLOSED when Socket n received the response successfully, or when timeout occurs (@ref Sn_IR[TIMEOUT] = . */ #define SOCK_LAST_ACK 0x1D /** * @brief UDP socket * @details This indicates Socket n is opened in UDP mode(Sn_MR(P[3:0]) = 010.\n * It changes to SOCK_UPD when Sn_MR(P[3:0]) = 010 and OPEN command is ordered.\n * Unlike TCP mode, data can be transfered without the connection-process. */ #define SOCK_UDP 0x22 //#define SOCK_IPRAW 0x32 /**< IP raw mode socket */ /** * @brief MAC raw mode socket * @details This indicates Socket 0 is opened in MACRAW mode (S0_MR(P[3:0]) = 100and is valid only in Socket 0.\n * It changes to SOCK_MACRAW when S0_MR(P[3:0] = 100and OPEN command is ordered.\n * Like UDP mode socket, MACRAW mode Socket 0 can transfer a MAC packet (Ethernet frame) without the connection-process. */ #define SOCK_MACRAW 0x42 //#define SOCK_PPPOE 0x5F /* IP PROTOCOL */ #define IPPROTO_IP 0 //< Dummy for IP #define IPPROTO_ICMP 1 //< Control message protocol #define IPPROTO_IGMP 2 //< Internet group management protocol #define IPPROTO_GGP 3 //< Gateway^2 (deprecated) #define IPPROTO_TCP 6 //< TCP #define IPPROTO_PUP 12 //< PUP #define IPPROTO_UDP 17 //< UDP #define IPPROTO_IDP 22 //< XNS idp #define IPPROTO_ND 77 //< UNOFFICIAL net disk protocol #define IPPROTO_RAW 255 //< Raw IP packet /** * @brief Enter a critical section * * @details It is provided to protect your shared code which are executed without distribution. \n \n * * In non-OS environment, It can be just implemented by disabling whole interrupt.\n * In OS environment, You can replace it to critical section api supported by OS. * * \sa WIZCHIP_READ(), WIZCHIP_WRITE(), WIZCHIP_READ_BUF(), WIZCHIP_WRITE_BUF() * \sa WIZCHIP_CRITICAL_EXIT() */ #define WIZCHIP_CRITICAL_ENTER() WIZCHIP.CRIS._enter() /** * @brief Exit a critical section * * @details It is provided to protect your shared code which are executed without distribution. \n\n * * In non-OS environment, It can be just implemented by disabling whole interrupt. \n * In OS environment, You can replace it to critical section api supported by OS. * * @sa WIZCHIP_READ(), WIZCHIP_WRITE(), WIZCHIP_READ_BUF(), WIZCHIP_WRITE_BUF() * @sa WIZCHIP_CRITICAL_ENTER() */ #ifdef _exit #undef _exit #endif #define WIZCHIP_CRITICAL_EXIT() WIZCHIP.CRIS._exit() //////////////////////// // Basic I/O Function // //////////////////////// /** * @ingroup Basic_IO_function * @brief It reads 1 byte value from a register. * @param AddrSel Register address * @return The value of register */ uint8_t WIZCHIP_READ (uint32_t AddrSel); /** * @ingroup Basic_IO_function * @brief It writes 1 byte value to a register. * @param AddrSel Register address * @param wb Write data * @return void */ void WIZCHIP_WRITE(uint32_t AddrSel, uint8_t wb ); /** * @ingroup Basic_IO_function * @brief It reads sequence data from registers. * @param AddrSel Register address * @param pBuf Pointer buffer to read data * @param len Data length */ void WIZCHIP_READ_BUF (uint32_t AddrSel, uint8_t* pBuf, uint16_t len); /** * @ingroup Basic_IO_function * @brief It writes sequence data to registers. * @param AddrSel Register address * @param pBuf Pointer buffer to write data * @param len Data length */ void WIZCHIP_WRITE_BUF(uint32_t AddrSel, uint8_t* pBuf, uint16_t len); ///////////////////////////////// // Common Register I/O function // ///////////////////////////////// /** * @ingroup Common_register_access_function * @brief Set Mode Register * @param (uint8_t)mr The value to be set. * @sa getMR() */ #define setMR(mr) \ WIZCHIP_WRITE(MR,mr) /** * @ingroup Common_register_access_function * @brief Get Mode Register * @return uint8_t. The value of Mode register. * @sa setMR() */ #define getMR() \ WIZCHIP_READ(MR) /** * @ingroup Common_register_access_function * @brief Set gateway IP address * @param (uint8_t*)gar Pointer variable to set gateway IP address. It should be allocated 4 bytes. * @sa getGAR() */ #define setGAR(gar) \ WIZCHIP_WRITE_BUF(GAR,gar,4) /** * @ingroup Common_register_access_function * @brief Get gateway IP address * @param (uint8_t*)gar Pointer variable to get gateway IP address. It should be allocated 4 bytes. * @sa setGAR() */ #define getGAR(gar) \ WIZCHIP_READ_BUF(GAR,gar,4) /** * @ingroup Common_register_access_function * @brief Set subnet mask address * @param (uint8_t*)subr Pointer variable to set subnet mask address. It should be allocated 4 bytes. * @sa getSUBR() */ #define setSUBR(subr) \ WIZCHIP_WRITE_BUF(SUBR, subr,4) /** * @ingroup Common_register_access_function * @brief Get subnet mask address * @param (uint8_t*)subr Pointer variable to get subnet mask address. It should be allocated 4 bytes. * @sa setSUBR() */ #define getSUBR(subr) \ WIZCHIP_READ_BUF(SUBR, subr, 4) /** * @ingroup Common_register_access_function * @brief Set local MAC address * @param (uint8_t*)shar Pointer variable to set local MAC address. It should be allocated 6 bytes. * @sa getSHAR() */ #define setSHAR(shar) \ WIZCHIP_WRITE_BUF(SHAR, shar, 6) /** * @ingroup Common_register_access_function * @brief Get local MAC address * @param (uint8_t*)shar Pointer variable to get local MAC address. It should be allocated 6 bytes. * @sa setSHAR() */ #define getSHAR(shar) \ WIZCHIP_READ_BUF(SHAR, shar, 6) /** * @ingroup Common_register_access_function * @brief Set local IP address * @param (uint8_t*)sipr Pointer variable to set local IP address. It should be allocated 4 bytes. * @sa getSIPR() */ #define setSIPR(sipr) \ WIZCHIP_WRITE_BUF(SIPR, sipr, 4) /** * @ingroup Common_register_access_function * @brief Get local IP address * @param (uint8_t*)sipr Pointer variable to get local IP address. It should be allocated 4 bytes. * @sa setSIPR() */ #define getSIPR(sipr) \ WIZCHIP_READ_BUF(SIPR, sipr, 4) /** * @ingroup Common_register_access_function * @brief Set INTLEVEL register * @param (uint16_t)intlevel Value to set @ref INTLEVEL register. * @sa getINTLEVEL() */ #define setINTLEVEL(intlevel) {\ WIZCHIP_WRITE(INTLEVEL, (uint8_t)(intlevel >> 8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(INTLEVEL,1), (uint8_t) intlevel); \ } /** * @ingroup Common_register_access_function * @brief Get INTLEVEL register * @return uint16_t. Value of @ref INTLEVEL register. * @sa setINTLEVEL() */ #define getINTLEVEL() \ ((WIZCHIP_READ(INTLEVEL) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(INTLEVEL,1))) /** * @ingroup Common_register_access_function * @brief Set @ref IR register * @param (uint8_t)ir Value to set @ref IR register. * @sa getIR() */ #define setIR(ir) \ WIZCHIP_WRITE(IR, (ir & 0xF0)) /** * @ingroup Common_register_access_function * @brief Get @ref IR register * @return uint8_t. Value of @ref IR register. * @sa setIR() */ #define getIR() \ (WIZCHIP_READ(IR) & 0xF0) /** * @ingroup Common_register_access_function * @brief Set @ref IMR register * @param (uint8_t)imr Value to set @ref IMR register. * @sa getIMR() */ #define setIMR(imr) \ WIZCHIP_WRITE(IMR, imr) /** * @ingroup Common_register_access_function * @brief Get @ref IMR register * @return uint8_t. Value of @ref IMR register. * @sa setIMR() */ #define getIMR() \ WIZCHIP_READ(IMR) /** * @ingroup Common_register_access_function * @brief Set @ref SIR register * @param (uint8_t)sir Value to set @ref SIR register. * @sa getSIR() */ #define setSIR(sir) \ WIZCHIP_WRITE(SIR, sir) /** * @ingroup Common_register_access_function * @brief Get @ref SIR register * @return uint8_t. Value of @ref SIR register. * @sa setSIR() */ #define getSIR() \ WIZCHIP_READ(SIR) /** * @ingroup Common_register_access_function * @brief Set @ref SIMR register * @param (uint8_t)simr Value to set @ref SIMR register. * @sa getSIMR() */ #define setSIMR(simr) \ WIZCHIP_WRITE(SIMR, simr) /** * @ingroup Common_register_access_function * @brief Get @ref SIMR register * @return uint8_t. Value of @ref SIMR register. * @sa setSIMR() */ #define getSIMR() \ WIZCHIP_READ(SIMR) /** * @ingroup Common_register_access_function * @brief Set @ref RTR register * @param (uint16_t)rtr Value to set @ref RTR register. * @sa getRTR() */ #define setRTR(rtr) {\ WIZCHIP_WRITE(RTR, (uint8_t)(rtr >> 8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(RTR,1), (uint8_t) rtr); \ } /** * @ingroup Common_register_access_function * @brief Get @ref RTR register * @return uint16_t. Value of @ref RTR register. * @sa setRTR() */ #define getRTR() \ ((WIZCHIP_READ(RTR) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(RTR,1))) /** * @ingroup Common_register_access_function * @brief Set @ref RCR register * @param (uint8_t)rcr Value to set @ref RCR register. * @sa getRCR() */ #define setRCR(rcr) \ WIZCHIP_WRITE(RCR, rcr) /** * @ingroup Common_register_access_function * @brief Get @ref RCR register * @return uint8_t. Value of @ref RCR register. * @sa setRCR() */ #define getRCR() \ WIZCHIP_READ(RCR) //================================================== test done =========================================================== /** * @ingroup Common_register_access_function * @brief Set @ref PTIMER register * @param (uint8_t)ptimer Value to set @ref PTIMER register. * @sa getPTIMER() */ #define setPTIMER(ptimer) \ WIZCHIP_WRITE(PTIMER, ptimer) /** * @ingroup Common_register_access_function * @brief Get @ref PTIMER register * @return uint8_t. Value of @ref PTIMER register. * @sa setPTIMER() */ #define getPTIMER() \ WIZCHIP_READ(PTIMER) /** * @ingroup Common_register_access_function * @brief Set @ref PMAGIC register * @param (uint8_t)pmagic Value to set @ref PMAGIC register. * @sa getPMAGIC() */ #define setPMAGIC(pmagic) \ WIZCHIP_WRITE(PMAGIC, pmagic) /** * @ingroup Common_register_access_function * @brief Get @ref PMAGIC register * @return uint8_t. Value of @ref PMAGIC register. * @sa setPMAGIC() */ #define getPMAGIC() \ WIZCHIP_READ(PMAGIC) /** * @ingroup Common_register_access_function * @brief Set PHAR address * @param (uint8_t*)phar Pointer variable to set PPP destination MAC register address. It should be allocated 6 bytes. * @sa getPHAR() */ #define setPHAR(phar) \ WIZCHIP_WRITE_BUF(PHAR, phar, 6) /** * @ingroup Common_register_access_function * @brief Get local IP address * @param (uint8_t*)phar Pointer variable to PPP destination MAC register address. It should be allocated 6 bytes. * @sa setPHAR() */ #define getPHAR(phar) \ WIZCHIP_READ_BUF(PHAR, phar, 6) /** * @ingroup Common_register_access_function * @brief Set @ref PSID register * @param (uint16_t)psid Value to set @ref PSID register. * @sa getPSID() */ #define setPSID(psid) {\ WIZCHIP_WRITE(PSID, (uint8_t)(psid >> 8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(PSID,1), (uint8_t) psid); \ } /** * @ingroup Common_register_access_function * @brief Get @ref PSID register * @return uint16_t. Value of @ref PSID register. * @sa setPSID() */ //uint16_t getPSID(void); #define getPSID() \ ((WIZCHIP_READ(PSID) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(PSID,1))) /** * @ingroup Common_register_access_function * @brief Set @ref PMRU register * @param (uint16_t)pmru Value to set @ref PMRU register. * @sa getPMRU() */ #define setPMRU(pmru) { \ WIZCHIP_WRITE(PMRU, (uint8_t)(pmru>>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(PMRU,1), (uint8_t) pmru); \ } /** * @ingroup Common_register_access_function * @brief Get @ref PMRU register * @return uint16_t. Value of @ref PMRU register. * @sa setPMRU() */ #define getPMRU() \ ((WIZCHIP_READ(PMRU) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(PMRU,1))) /** * @ingroup Common_register_access_function * @brief Get unreachable IP address * @param (uint8_t*)uipr Pointer variable to get unreachable IP address. It should be allocated 4 bytes. */ #define getUIPR(uipr) \ WIZCHIP_READ_BUF(UIPR,uipr,6) /** * @ingroup Common_register_access_function * @brief Get @ref UPORTR register * @return uint16_t. Value of @ref UPORTR register. */ #define getUPORTR() \ ((WIZCHIP_READ(UPORTR) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(UPORTR,1))) /** * @ingroup Common_register_access_function * @brief Set @ref PHYCFGR register * @param (uint8_t)phycfgr Value to set @ref PHYCFGR register. * @sa getPHYCFGR() */ #define setPHYCFGR(phycfgr) \ WIZCHIP_WRITE(PHYCFGR, phycfgr) /** * @ingroup Common_register_access_function * @brief Get @ref PHYCFGR register * @return uint8_t. Value of @ref PHYCFGR register. * @sa setPHYCFGR() */ #define getPHYCFGR() \ WIZCHIP_READ(PHYCFGR) /** * @ingroup Common_register_access_function * @brief Get @ref VERSIONR register * @return uint8_t. Value of @ref VERSIONR register. */ #define getVERSIONR() \ WIZCHIP_READ(VERSIONR) ///////////////////////////////////// /////////////////////////////////// // Socket N register I/O function // /////////////////////////////////// /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_MR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)mr Value to set @ref Sn_MR * @sa getSn_MR() */ #define setSn_MR(sn, mr) \ WIZCHIP_WRITE(Sn_MR(sn),mr) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_MR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_MR. * @sa setSn_MR() */ #define getSn_MR(sn) \ WIZCHIP_READ(Sn_MR(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_CR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)cr Value to set @ref Sn_CR * @sa getSn_CR() */ #define setSn_CR(sn, cr) \ WIZCHIP_WRITE(Sn_CR(sn), cr) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_CR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_CR. * @sa setSn_CR() */ #define getSn_CR(sn) \ WIZCHIP_READ(Sn_CR(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_IR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)ir Value to set @ref Sn_IR * @sa getSn_IR() */ #define setSn_IR(sn, ir) \ WIZCHIP_WRITE(Sn_IR(sn), (ir & 0x1F)) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_IR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_IR. * @sa setSn_IR() */ #define getSn_IR(sn) \ (WIZCHIP_READ(Sn_IR(sn)) & 0x1F) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_IMR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)imr Value to set @ref Sn_IMR * @sa getSn_IMR() */ #define setSn_IMR(sn, imr) \ WIZCHIP_WRITE(Sn_IMR(sn), (imr & 0x1F)) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_IMR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_IMR. * @sa setSn_IMR() */ #define getSn_IMR(sn) \ (WIZCHIP_READ(Sn_IMR(sn)) & 0x1F) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_SR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_SR. */ #define getSn_SR(sn) \ WIZCHIP_READ(Sn_SR(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_PORT register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)port Value to set @ref Sn_PORT. * @sa getSn_PORT() */ #define setSn_PORT(sn, port) { \ WIZCHIP_WRITE(Sn_PORT(sn), (uint8_t)(port >> 8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_PORT(sn),1), (uint8_t) port); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_PORT register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_PORT. * @sa setSn_PORT() */ #define getSn_PORT(sn) \ ((WIZCHIP_READ(Sn_PORT(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_PORT(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_DHAR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t*)dhar Pointer variable to set socket n destination hardware address. It should be allocated 6 bytes. * @sa getSn_DHAR() */ #define setSn_DHAR(sn, dhar) \ WIZCHIP_WRITE_BUF(Sn_DHAR(sn), dhar, 6) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_MR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t*)dhar Pointer variable to get socket n destination hardware address. It should be allocated 6 bytes. * @sa setSn_DHAR() */ #define getSn_DHAR(sn, dhar) \ WIZCHIP_READ_BUF(Sn_DHAR(sn), dhar, 6) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_DIPR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t*)dipr Pointer variable to set socket n destination IP address. It should be allocated 4 bytes. * @sa getSn_DIPR() */ #define setSn_DIPR(sn, dipr) \ WIZCHIP_WRITE_BUF(Sn_DIPR(sn), dipr, 4) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_DIPR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t*)dipr Pointer variable to get socket n destination IP address. It should be allocated 4 bytes. * @sa SetSn_DIPR() */ #define getSn_DIPR(sn, dipr) \ WIZCHIP_READ_BUF(Sn_DIPR(sn), dipr, 4) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_DPORT register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)dport Value to set @ref Sn_DPORT * @sa getSn_DPORT() */ #define setSn_DPORT(sn, dport) { \ WIZCHIP_WRITE(Sn_DPORT(sn), (uint8_t) (dport>>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_DPORT(sn),1), (uint8_t) dport); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_DPORT register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_DPORT. * @sa setSn_DPORT() */ #define getSn_DPORT(sn) \ ((WIZCHIP_READ(Sn_DPORT(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_DPORT(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_MSSR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)mss Value to set @ref Sn_MSSR * @sa setSn_MSSR() */ #define setSn_MSSR(sn, mss) { \ WIZCHIP_WRITE(Sn_MSSR(sn), (uint8_t)(mss>>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_MSSR(sn),1), (uint8_t) mss); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_MSSR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_MSSR. * @sa setSn_MSSR() */ #define getSn_MSSR(sn) \ ((WIZCHIP_READ(Sn_MSSR(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_MSSR(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_TOS register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)tos Value to set @ref Sn_TOS * @sa getSn_TOS() */ #define setSn_TOS(sn, tos) \ WIZCHIP_WRITE(Sn_TOS(sn), tos) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TOS register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of Sn_TOS. * @sa setSn_TOS() */ #define getSn_TOS(sn) \ WIZCHIP_READ(Sn_TOS(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_TTL register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)ttl Value to set @ref Sn_TTL * @sa getSn_TTL() */ #define setSn_TTL(sn, ttl) \ WIZCHIP_WRITE(Sn_TTL(sn), ttl) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TTL register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_TTL. * @sa setSn_TTL() */ #define getSn_TTL(sn) \ WIZCHIP_READ(Sn_TTL(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_RXBUF_SIZE register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)rxbufsize Value to set @ref Sn_RXBUF_SIZE * @sa getSn_RXBUF_SIZE() */ #define setSn_RXBUF_SIZE(sn, rxbufsize) \ WIZCHIP_WRITE(Sn_RXBUF_SIZE(sn),rxbufsize) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_RXBUF_SIZE register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_RXBUF_SIZE. * @sa setSn_RXBUF_SIZE() */ #define getSn_RXBUF_SIZE(sn) \ WIZCHIP_READ(Sn_RXBUF_SIZE(sn)) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_TXBUF_SIZE register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)txbufsize Value to set @ref Sn_TXBUF_SIZE * @sa getSn_TXBUF_SIZE() */ #define setSn_TXBUF_SIZE(sn, txbufsize) \ WIZCHIP_WRITE(Sn_TXBUF_SIZE(sn), txbufsize) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TXBUF_SIZE register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_TXBUF_SIZE. * @sa setSn_TXBUF_SIZE() */ #define getSn_TXBUF_SIZE(sn) \ WIZCHIP_READ(Sn_TXBUF_SIZE(sn)) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TX_FSR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_TX_FSR. */ uint16_t getSn_TX_FSR(uint8_t sn); /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TX_RD register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_TX_RD. */ #define getSn_TX_RD(sn) \ ((WIZCHIP_READ(Sn_TX_RD(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_TX_RD(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_TX_WR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)txwr Value to set @ref Sn_TX_WR * @sa GetSn_TX_WR() */ #define setSn_TX_WR(sn, txwr) { \ WIZCHIP_WRITE(Sn_TX_WR(sn), (uint8_t)(txwr>>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_TX_WR(sn),1), (uint8_t) txwr); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_TX_WR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_TX_WR. * @sa setSn_TX_WR() */ #define getSn_TX_WR(sn) \ ((WIZCHIP_READ(Sn_TX_WR(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_TX_WR(sn),1))) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_RX_RSR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_RX_RSR. */ uint16_t getSn_RX_RSR(uint8_t sn); /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_RX_RD register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)rxrd Value to set @ref Sn_RX_RD * @sa getSn_RX_RD() */ #define setSn_RX_RD(sn, rxrd) { \ WIZCHIP_WRITE(Sn_RX_RD(sn), (uint8_t)(rxrd>>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_RX_RD(sn),1), (uint8_t) rxrd); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_RX_RD register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @regurn uint16_t. Value of @ref Sn_RX_RD. * @sa setSn_RX_RD() */ #define getSn_RX_RD(sn) \ ((WIZCHIP_READ(Sn_RX_RD(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_RX_RD(sn),1))) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_RX_WR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_RX_WR. */ #define getSn_RX_WR(sn) \ ((WIZCHIP_READ(Sn_RX_WR(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_RX_WR(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_FRAG register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint16_t)frag Value to set @ref Sn_FRAG * @sa getSn_FRAD() */ #define setSn_FRAG(sn, frag) { \ WIZCHIP_WRITE(Sn_FRAG(sn), (uint8_t)(frag >>8)); \ WIZCHIP_WRITE(WIZCHIP_OFFSET_INC(Sn_FRAG(sn),1), (uint8_t) frag); \ } /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_FRAG register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of @ref Sn_FRAG. * @sa setSn_FRAG() */ #define getSn_FRAG(sn) \ ((WIZCHIP_READ(Sn_FRAG(sn)) << 8) + WIZCHIP_READ(WIZCHIP_OFFSET_INC(Sn_FRAG(sn),1))) /** * @ingroup Socket_register_access_function * @brief Set @ref Sn_KPALVTR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param (uint8_t)kpalvt Value to set @ref Sn_KPALVTR * @sa getSn_KPALVTR() */ #define setSn_KPALVTR(sn, kpalvt) \ WIZCHIP_WRITE(Sn_KPALVTR(sn), kpalvt) /** * @ingroup Socket_register_access_function * @brief Get @ref Sn_KPALVTR register * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint8_t. Value of @ref Sn_KPALVTR. * @sa setSn_KPALVTR() */ #define getSn_KPALVTR(sn) \ WIZCHIP_READ(Sn_KPALVTR(sn)) ////////////////////////////////////// ///////////////////////////////////// // Sn_TXBUF & Sn_RXBUF IO function // ///////////////////////////////////// /** * @brief Gets the max buffer size of socket sn passed as parameter. * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of Socket n RX max buffer size. */ #define getSn_RxMAX(sn) \ (getSn_RXBUF_SIZE(sn) << 10) /** * @brief Gets the max buffer size of socket sn passed as parameters. * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @return uint16_t. Value of Socket n TX max buffer size. */ //uint16_t getSn_TxMAX(uint8_t sn); #define getSn_TxMAX(sn) \ (getSn_TXBUF_SIZE(sn) << 10) /** * @ingroup Basic_IO_function * @brief It copies data to internal TX memory * * @details This function reads the Tx write pointer register and after that, * it copies the wizdata(pointer buffer) of the length of len(variable) bytes to internal TX memory * and updates the Tx write pointer register. * This function is being called by send() and sendto() function also. * * @note User should read upper byte first and lower byte later to get proper value. * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param wizdata Pointer buffer to write data * @param len Data length * @sa wiz_recv_data() */ void wiz_send_data(uint8_t sn, uint8_t *wizdata, uint16_t len); /** * @ingroup Basic_IO_function * @brief It copies data to your buffer from internal RX memory * * @details This function read the Rx read pointer register and after that, * it copies the received data from internal RX memory * to wizdata(pointer variable) of the length of len(variable) bytes. * This function is being called by recv() also. * * @note User should read upper byte first and lower byte later to get proper value. * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param wizdata Pointer buffer to read data * @param len Data length * @sa wiz_send_data() */ void wiz_recv_data(uint8_t sn, uint8_t *wizdata, uint16_t len); /** * @ingroup Basic_IO_function * @brief It discard the received data in RX memory. * @details It discards the data of the length of len(variable) bytes in internal RX memory. * @param (uint8_t)sn Socket number. It should be 0 ~ 7. * @param len Data length */ void wiz_recv_ignore(uint8_t sn, uint16_t len); #endif // _W5500_H_