.. _intro: Getting started with MicroPython on the ESP8266 =============================================== Using MicroPython is a great way to get the most of your ESP8266 board. And vice versa, the ESP8266 chip is a great platform for using MicroPython. This tutorial will guide you through setting up MicroPython, getting a prompt, using WebREPL, connecting to the network and communicating with the Internet, using the hardware peripherals, and controlling some external components. Let's get started! Requirements ------------ The first thing you need is a board with an ESP8266 chip. The MicroPython software supports the ESP8266 chip itself and any board should work. The main characteristic of a board is how much flash it has, how the GPIO pins are connected to the outside world, and whether it includes a built-in USB-serial convertor to make the UART available to your PC. The minimum requirement for flash size is 512k. A board with this amount of flash will not have room for a filesystem, but otherwise is fully functional. If your board has 1Mbyte or more of flash then it will support a filesystem. Names of pins will be given in this tutorial using the chip names (eg GPIO0) and it should be straightforward to find which pin this corresponds to on your particular board. Powering the board ------------------ If your board has a USB connector on it then most likely it is powered through this when connected to your PC. Otherwise you will need to power it directly. Please refer to the documentation for your board for further details. Deploying the firmware ---------------------- The very first thing you need to do is put the MicroPython firmware (compiled code) on your ESP8266 device. There are two main steps to do this: first you need to put your device in boot-loader mode, and second you need to copy across the firmware. The exact procedure for these steps is highly dependent on the particular board and you will need to refer to its documentation for details. If you have a board that has a USB connector, a USB-serial convertor, and has the DTR and RTS pins wired in a special way then deploying the firmware should be easy as all steps can be done automatically. Boards that have such features include the Adafruit Feather HUZZAH and NodeMCU boards. For best results it is recommended to first erase the entire flash of your device before putting on new MicroPython firmware. Currently we only support esptool.py to copy across the firmware. You can find this tool here: ``__, or install it using pip:: pip install esptool It requires Python 2.7, so you may need to use ``pip2`` instead of ``pip`` in the command above. Any other flashing program should work, so feel free to try them out, or refer to the documentation for your board to see its recommendations. Using esptool.py you can erase the flash with the command:: esptool.py --port /dev/ttyUSB0 erase_flash And then deploy the new firmware using:: esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash --flash_size=8m 0 esp8266-2016-05-03-v1.8.bin You might need to change the "port" setting to something else relevant for your PC. You may also need to reduce the baudrate if you get errors when flashing (eg down to 115200). The filename of the firmware should also match the file that you have. For some boards with a particular FlashROM configuration (e.g. some variants of a NodeMCU board) you may need to use the following command to deploy the firmware (note the ``-fm dio`` option):: esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash --flash_size=8m -fm dio 0 esp8266-2016-05-03-v1.8.bin If the above commands run without error then MicroPython should be installed on your board! Serial prompt ------------- Once you have the firmware on the device you can access the REPL (Python prompt) over UART0 (GPIO1=TX, GPIO3=RX), which might be connected to a USB-serial convertor, depending on your board. The baudrate is 115200. The next part of the tutorial will discuss the prompt in more detail. WiFi ---- After a fresh install and boot the device configures itself as a WiFi access point (AP) that you can connect to. The ESSID is of the form MicroPython-xxxxxx where the x's are replaced with part of the MAC address of your device (so will be the same everytime, and most likely different for all ESP8266 chips). The password for the WiFi is micropythoN (note the upper-case N). Its IP address will be 192.168.4.1 once you connect to its network. WiFi configuration will be discussed in more detail later in the tutorial. Troubleshooting installation problems ------------------------------------- If you experience problems during flashing or with running firmware immediately after it, here are troubleshooting recommendations: * Be aware of and try to exclude hardware problems. There are 2 common problems: bad power source quality and worn-out/defective FlashROM. Speaking of power source, not just raw amperage is important, but also low ripple and noise/EMI in general. If you experience issues with self-made or wall-wart style power supply, try USB power from a computer. Unearthed power supplies are also known to cause problems as they source of increased EMI (electromagnetic interference) - at the very least, and may lead to electrical devices breakdown. So, you are advised to avoid using unearthed power connections when working with ESP8266 and other boards. In regard to FlashROM hardware problems, there are independent (not related to MicroPython in any way) reports `(e.g.) `_ that on some ESP8266 modules, FlashROM can be programmed as little as 20 times before programming errors occur. This is *much* less than 100,000 programming cycles cited for FlashROM chips of a type used with ESP8266 by reputable vendors, which points to either production rejects, or second-hand worn-out flash chips to be used on some (apparently cheap) modules/boards. You may want to use your best judgement about source, price, documentation, warranty, post-sales support for the modules/boards you purchase. * The flashing instructions above use flashing speed of 460800 baud, which is good compromise between speed and stability. However, depending on your module/board, USB-UART convertor, cables, host OS, etc., the above baud rate may be too high and lead to errors. Try a more common 115200 baud rate instead in such cases. * If lower baud rate didn't help, you may want to try older version of esptool.py, which had a different programming algorithm:: pip install esptool==1.0.1 * The ``--flash_size`` option in the commands above is mandatory. Omitting it will lead to a corrupted firmware. * To catch incorrect flash content (e.g. from a defective sector on a chip), add ``--verify`` switch to the commands above. * Additionally, you can check the firmware integrity from a MicroPython REPL prompt (assuming you were able to flash it and ``--verify`` option doesn't report errors):: import esp esp.check_fw() If the last output value is True, the firmware is OK. Otherwise, it's corrupted and need to be reflashed correctly. * If you experience any issues with another flashing application (not esptool.py), try esptool.py, it is a generally accepted flashing application in the ESP8266 community. * If you still experience problems with even flashing the firmware, please refer to esptool.py project page, https://github.com/themadinventor/esptool for additional documentation and bug tracker where you can report problems. * If you are able to flash firmware, but ``--verify`` option or ``esp.check_fw()`` return errors even after multiple retries, you may have a defective FlashROM chip, as explained above.