**************************************** :mod:`network` --- network configuration **************************************** .. module:: network :synopsis: network configuration This module provides network drivers and routing configuration. Network drivers for specific hardware are available within this module and are used to configure a hardware network interface. Configured interfaces are then available for use via the :mod:`socket` module. To use this module the network build of firmware must be installed. For example:: # configure a specific network interface # see below for examples of specific drivers import network nic = network.Driver(...) print(nic.ifconfig()) # now use socket as usual import socket addr = socket.getaddrinfo('micropython.org', 80)[0][-1] s = socket.socket() s.connect(addr) s.send(b'GET / HTTP/1.1\r\nHost: micropython.org\r\n\r\n') data = s.recv(1000) s.close() .. only:: port_wipy .. _network.Server: class Server ============ The ``Server`` class controls the behaviour and the configuration of the FTP and telnet services running on the WiPy. Any changes performed using this class' methods will affect both. Example:: import network server = network.Server() server.deinit() # disable the server # enable the server again with new settings server.init(login=('user', 'password'), timeout=600) Constructors ------------ .. class:: network.Server(id, ...) Create a server instance, see ``init`` for parameters of initialization. Methods ------- .. method:: server.init(\*, login=('micro', 'python'), timeout=300) Init (and effectively start the server). Optionally a new ``user``, ``password`` and ``timeout`` (in seconds) can be passed. .. method:: server.deinit() Stop the server .. method:: server.timeout([timeout_in_seconds]) Get or set the server timeout. .. method:: server.isrunning() Returns ``True`` if the server is running, ``False`` otherwise. .. only:: port_pyboard class CC3K ========== This class provides a driver for CC3000 wifi modules. Example usage:: import network nic = network.CC3K(pyb.SPI(2), pyb.Pin.board.Y5, pyb.Pin.board.Y4, pyb.Pin.board.Y3) nic.connect('your-ssid', 'your-password') while not nic.isconnected(): pyb.delay(50) print(nic.ifconfig()) # now use socket as usual ... For this example to work the CC3000 module must have the following connections: - MOSI connected to Y8 - MISO connected to Y7 - CLK connected to Y6 - CS connected to Y5 - VBEN connected to Y4 - IRQ connected to Y3 It is possible to use other SPI busses and other pins for CS, VBEN and IRQ. Constructors ------------ .. class:: CC3K(spi, pin_cs, pin_en, pin_irq) Create a CC3K driver object, initialise the CC3000 module using the given SPI bus and pins, and return the CC3K object. Arguments are: - ``spi`` is an :ref:`SPI object ` which is the SPI bus that the CC3000 is connected to (the MOSI, MISO and CLK pins). - ``pin_cs`` is a :ref:`Pin object ` which is connected to the CC3000 CS pin. - ``pin_en`` is a :ref:`Pin object ` which is connected to the CC3000 VBEN pin. - ``pin_irq`` is a :ref:`Pin object ` which is connected to the CC3000 IRQ pin. All of these objects will be initialised by the driver, so there is no need to initialise them yourself. For example, you can use:: nic = network.CC3K(pyb.SPI(2), pyb.Pin.board.Y5, pyb.Pin.board.Y4, pyb.Pin.board.Y3) Methods ------- .. method:: cc3k.connect(ssid, key=None, \*, security=WPA2, bssid=None) Connect to a wifi access point using the given SSID, and other security parameters. .. method:: cc3k.disconnect() Disconnect from the wifi access point. .. method:: cc3k.isconnected() Returns True if connected to a wifi access point and has a valid IP address, False otherwise. .. method:: cc3k.ifconfig() Returns a 7-tuple with (ip, subnet mask, gateway, DNS server, DHCP server, MAC address, SSID). .. method:: cc3k.patch_version() Return the version of the patch program (firmware) on the CC3000. .. method:: cc3k.patch_program('pgm') Upload the current firmware to the CC3000. You must pass 'pgm' as the first argument in order for the upload to proceed. Constants --------- .. data:: CC3K.WEP .. data:: CC3K.WPA .. data:: CC3K.WPA2 security type to use class WIZNET5K ============== This class allows you to control WIZnet5x00 Ethernet adaptors based on the W5200 and W5500 chipsets (only W5200 tested). Example usage:: import network nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4) print(nic.ifconfig()) # now use socket as usual ... For this example to work the WIZnet5x00 module must have the following connections: - MOSI connected to X8 - MISO connected to X7 - SCLK connected to X6 - nSS connected to X5 - nRESET connected to X4 It is possible to use other SPI busses and other pins for nSS and nRESET. Constructors ------------ .. class:: WIZNET5K(spi, pin_cs, pin_rst) Create a WIZNET5K driver object, initialise the WIZnet5x00 module using the given SPI bus and pins, and return the WIZNET5K object. Arguments are: - ``spi`` is an :ref:`SPI object ` which is the SPI bus that the WIZnet5x00 is connected to (the MOSI, MISO and SCLK pins). - ``pin_cs`` is a :ref:`Pin object ` which is connected to the WIZnet5x00 nSS pin. - ``pin_rst`` is a :ref:`Pin object ` which is connected to the WIZnet5x00 nRESET pin. All of these objects will be initialised by the driver, so there is no need to initialise them yourself. For example, you can use:: nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4) Methods ------- .. method:: wiznet5k.ifconfig([(ip, subnet, gateway, dns)]) Get/set IP address, subnet mask, gateway and DNS. When called with no arguments, this method returns a 4-tuple with the above information. To set the above values, pass a 4-tuple with the required information. For example:: nic.ifconfig(('192.168.0.4', '255.255.255.0', '192.168.0.1', '8.8.8.8')) .. method:: wiznet5k.regs() Dump the WIZnet5x00 registers. Useful for debugging. .. _network.WLAN: .. only:: port_esp8266 Functions ========= .. function:: phy_mode([mode]) Get or set the PHY mode. If the ``mode`` parameter is provided, sets the mode to its value. If the function is called wihout parameters, returns the current mode. The possible modes are defined as constants: * ``MODE_11B`` -- IEEE 802.11b, * ``MODE_11G`` -- IEEE 802.11g, * ``MODE_11N`` -- IEEE 802.11n. class WLAN ========== This class provides a driver for WiFi network processor in the ESP8266. Example usage:: import network # enable station interface and connect to WiFi access point nic = network.WLAN(network.STA_IF) nic.active(True) nic.connect('your-ssid', 'your-password') # now use sockets as usual Constructors ------------ .. class:: WLAN(interface_id) Create a WLAN network interface object. Supported interfaces are ``network.STA_IF`` (station aka client, connects to upstream WiFi access points) and ``network.AP_IF`` (access point, allows other WiFi clients to connect). Availability of the methods below depends on interface type. For example, only STA interface may ``connect()`` to an access point. Methods ------- .. method:: wlan.active([is_active]) Activate ("up") or deactivate ("down") network interface, if boolean argument is passed. Otherwise, query current state if no argument is provided. Most other methods require active interface. .. method:: wlan.connect(ssid, password) Connect to the specified wireless network, using the specified password. .. method:: wlan.disconnect() Disconnect from the currently connected wireless network. .. method:: wlan.mac([address]) Get or set the network interface MAC address. If the ``address`` parameter is provided, sets the address to its value, which should be bytes object of length 6. If the function is called wihout parameters, returns the current address. .. method:: wlan.scan() Scan for the available wireless networks. Scanning is only possible on STA interface. Returns list of tuples with the information about WiFi access points: (ssid, bssid, channel, RSSI, authmode, hidden) There are five values for authmode: * 0 -- open * 1 -- WEP * 2 -- WPA-PSK * 3 -- WPA2-PSK * 4 -- WPA/WPA2-PSK and two for hidden: * 0 -- visible * 1 -- hidden .. method:: wlan.status() Return the current status of the wireless connection. The possible statuses are defined as constants: * ``STAT_IDLE`` -- no connection and no activity, * ``STAT_CONNECTING`` -- connecting in progress, * ``STAT_WRONG_PASSWORD`` -- failed due to incorrect password, * ``STAT_NO_AP_FOUND`` -- failed because no access point replied, * ``STAT_CONNECT_FAIL`` -- failed due to other problems, * ``STAT_GOT_IP`` -- connection susccessful. .. method:: wlan.isconnected() In case of STA mode, returns ``True`` if connected to a wifi access point and has a valid IP address. In AP mode returns ``True`` when a station is connected. Returns ``False`` otherwise. .. only:: port_wipy class WLAN ========== This class provides a driver for the WiFi network processor in the WiPy. Example usage:: import network import time # setup as a station wlan = network.WLAN(mode=WLAN.STA) wlan.connect('your-ssid', auth=(WLAN.WPA2, 'your-key')) while not wlan.isconnected(): time.sleep_ms(50) print(wlan.ifconfig()) # now use socket as usual ... Constructors ------------ .. class:: WLAN(id=0, ...) Create a WLAN object, and optionally configure it. See ``init`` for params of configuration. .. note:: The ``WLAN`` constructor is special in the sense that if no arguments besides the id are given, it will return the already exisiting ``WLAN`` instance without re-configuring it. This is because ``WLAN`` is a system feature of the WiPy. If the already existing instance is not initialized it will do the same as the other constructors an will initialize it with default values. Methods ------- .. method:: wlan.init(mode, \*, ssid, auth, channel, antenna) Set or get the WiFi network processor configuration. Arguments are: - ``mode`` can be either ``WLAN.STA`` or ``WLAN.AP``. - ``ssid`` is a string with the ssid name. Only needed when mode is ``WLAN.AP``. - ``auth`` is a tuple with (sec, key). Security can be ``None``, ``WLAN.WEP``, ``WLAN.WPA`` or ``WLAN.WPA2``. The key is a string with the network password. If ``sec`` is ``WLAN.WEP`` the key must be a string representing hexadecimal values (e.g. 'ABC1DE45BF'). Only needed when mode is ``WLAN.AP``. - ``channel`` a number in the range 1-11. Only needed when mode is ``WLAN.AP``. - ``antenna`` selects between the internal and the external antenna. Can be either ``WLAN.INT_ANT`` or ``WLAN.EXT_ANT``. For example, you can do:: # create and configure as an access point wlan.init(mode=WLAN.AP, ssid='wipy-wlan', auth=(WLAN.WPA2,'www.wipy.io'), channel=7, antenna=WLAN.INT_ANT) or:: # configure as an station wlan.init(mode=WLAN.STA) .. method:: wlan.connect(ssid, \*, auth=None, bssid=None, timeout=None) Connect to a wifi access point using the given SSID, and other security parameters. - ``auth`` is a tuple with (sec, key). Security can be ``None``, ``WLAN.WEP``, ``WLAN.WPA`` or ``WLAN.WPA2``. The key is a string with the network password. If ``sec`` is ``WLAN.WEP`` the key must be a string representing hexadecimal values (e.g. 'ABC1DE45BF'). - ``bssid`` is the MAC address of the AP to connect to. Useful when there are several APs with the same ssid. - ``timeout`` is the maximum time in milliseconds to wait for the connection to succeed. .. method:: wlan.scan() Performs a network scan and returns a list of named tuples with (ssid, bssid, sec, channel, rssi). Note that channel is always ``None`` since this info is not provided by the WiPy. .. method:: wlan.disconnect() Disconnect from the wifi access point. .. method:: wlan.isconnected() In case of STA mode, returns ``True`` if connected to a wifi access point and has a valid IP address. In AP mode returns ``True`` when a station is connected, ``False`` otherwise. .. method:: wlan.ifconfig(if_id=0, config=['dhcp' or configtuple]) With no parameters given eturns a 4-tuple of ``(ip, subnet_mask, gateway, DNS_server)``. if ``'dhcp'`` is passed as a parameter then the DHCP client is enabled and the IP params are negotiated with the AP. If the 4-tuple config is given then a static IP is configured. For instance:: wlan.ifconfig(config=('192.168.0.4', '255.255.255.0', '192.168.0.1', '8.8.8.8')) .. method:: wlan.mode([mode]) Get or set the WLAN mode. .. method:: wlan.ssid([ssid]) Get or set the SSID when in AP mode. .. method:: wlan.auth([auth]) Get or set the authentication type when in AP mode. .. method:: wlan.channel([channel]) Get or set the channel (only applicable in AP mode). .. method:: wlan.antenna([antenna]) Get or set the antenna type (external or internal). .. method:: wlan.mac([mac_addr]) Get or set a 6-byte long bytes object with the MAC address. .. method:: wlan.irq(\*, handler, wake) Create a callback to be triggered when a WLAN event occurs during ``machine.SLEEP`` mode. Events are triggered by socket activity or by WLAN connection/disconnection. - ``handler`` is the function that gets called when the irq is triggered. - ``wake`` must be ``machine.SLEEP``. Returns an irq object. Constants --------- .. data:: WLAN.STA .. data:: WLAN.AP selects the WLAN mode .. data:: WLAN.WEP .. data:: WLAN.WPA .. data:: WLAN.WPA2 selects the network security .. data:: WLAN.INT_ANT .. data:: WLAN.EXT_ANT selects the antenna type