/* * This file is part of the MicroPython project, http://micropython.org/ * * The MIT License (MIT) * * Copyright (c) 2018-2019 Damien P. George * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. */ #define MICROPY_HW_BOARD_NAME "PYBD-SF2W" #define MICROPY_HW_MCU_NAME "STM32F722IEK" #define MICROPY_PY_PYB_LEGACY (1) #define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0) #define MICROPY_HW_HAS_SWITCH (1) #define MICROPY_HW_HAS_FLASH (1) #define MICROPY_HW_ENABLE_RNG (1) #define MICROPY_HW_ENABLE_RTC (1) #define MICROPY_HW_ENABLE_TIMER (1) #define MICROPY_HW_ENABLE_SERVO (1) #define MICROPY_HW_ENABLE_DAC (1) #define MICROPY_HW_ENABLE_USB (1) #define MICROPY_HW_ENABLE_SDCARD (1) #define MICROPY_HW_ENABLE_MMCARD (1) #define MICROPY_HW_ENABLE_RF_SWITCH (1) #define MICROPY_BOARD_EARLY_INIT board_early_init #define MICROPY_BOARD_ENTER_STOP board_sleep(1); #define MICROPY_BOARD_LEAVE_STOP board_sleep(0); #define MICROPY_BOARD_ENTER_STANDBY board_sleep(1); #define MICROPY_BOARD_SDCARD_POWER mp_hal_pin_high(pyb_pin_EN_3V3); void board_early_init(void); void board_sleep(int value); // HSE is 25MHz, run SYS at 120MHz #define MICROPY_HW_CLK_PLLM (20) #define MICROPY_HW_CLK_PLLN (192) #define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) #define MICROPY_HW_CLK_PLLQ (5) #define MICROPY_HW_FLASH_LATENCY (FLASH_LATENCY_3) // There is an external 32kHz oscillator #define RTC_ASYNCH_PREDIV (3) #define RTC_SYNCH_PREDIV (0x1fff) #define MICROPY_HW_RTC_USE_BYPASS (1) #define MICROPY_HW_RTC_USE_US (1) #define MICROPY_HW_RTC_USE_CALOUT (1) // SPI flash #1, for R/W storage #define MICROPY_HW_SOFTQSPI_SCK_LOW(self) (GPIOE->BSRR = (0x10000 << 11)) #define MICROPY_HW_SOFTQSPI_SCK_HIGH(self) (GPIOE->BSRR = (1 << 11)) #define MICROPY_HW_SOFTQSPI_NIBBLE_READ(self) ((GPIOE->IDR >> 7) & 0xf) #define MICROPY_HW_SPIFLASH_SIZE_BITS (16 * 1024 * 1024) #define MICROPY_HW_SPIFLASH_CS (pyb_pin_QSPI1_CS) #define MICROPY_HW_SPIFLASH_SCK (pyb_pin_QSPI1_CLK) #define MICROPY_HW_SPIFLASH_IO0 (pyb_pin_QSPI1_D0) #define MICROPY_HW_SPIFLASH_IO1 (pyb_pin_QSPI1_D1) #define MICROPY_HW_SPIFLASH_IO2 (pyb_pin_QSPI1_D2) #define MICROPY_HW_SPIFLASH_IO3 (pyb_pin_QSPI1_D3) // SPI flash #1, block device config extern const struct _mp_spiflash_config_t spiflash_config; extern struct _spi_bdev_t spi_bdev; #if !BUILDING_MBOOT #define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) #endif #define MICROPY_HW_BDEV_IOCTL(op, arg) ( \ (op) == BDEV_IOCTL_NUM_BLOCKS ? (MICROPY_HW_SPIFLASH_SIZE_BITS / 8 / FLASH_BLOCK_SIZE) : \ (op) == BDEV_IOCTL_INIT ? spi_bdev_ioctl(&spi_bdev, (op), (uint32_t)&spiflash_config) : \ spi_bdev_ioctl(&spi_bdev, (op), (arg)) \ ) #define MICROPY_HW_BDEV_READBLOCKS(dest, bl, n) spi_bdev_readblocks(&spi_bdev, (dest), (bl), (n)) #define MICROPY_HW_BDEV_WRITEBLOCKS(src, bl, n) spi_bdev_writeblocks(&spi_bdev, (src), (bl), (n)) #define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol // SPI flash #2, to be memory mapped #define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (24) #define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS) #define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK) #define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0) #define MICROPY_HW_QSPIFLASH_IO1 (pyb_pin_QSPI2_D1) #define MICROPY_HW_QSPIFLASH_IO2 (pyb_pin_QSPI2_D2) #define MICROPY_HW_QSPIFLASH_IO3 (pyb_pin_QSPI2_D3) // SPI flash #2, block device config extern const struct _mp_spiflash_config_t spiflash2_config; extern struct _spi_bdev_t spi_bdev2; // UART config #define MICROPY_HW_UART1_NAME "YA" #define MICROPY_HW_UART1_TX (pyb_pin_Y1) #define MICROPY_HW_UART1_RX (pyb_pin_Y2) #define MICROPY_HW_UART2_TX (pyb_pin_X3) #define MICROPY_HW_UART2_RX (pyb_pin_X4) #define MICROPY_HW_UART2_RTS (pyb_pin_X2) #define MICROPY_HW_UART2_CTS (pyb_pin_X1) #define MICROPY_HW_UART3_NAME "YB" #define MICROPY_HW_UART3_TX (pyb_pin_Y9) #define MICROPY_HW_UART3_RX (pyb_pin_Y10) #define MICROPY_HW_UART4_NAME "XA" #define MICROPY_HW_UART4_TX (pyb_pin_X1) #define MICROPY_HW_UART4_RX (pyb_pin_X2) #define MICROPY_HW_UART6_TX (pyb_pin_BT_TXD) #define MICROPY_HW_UART6_RX (pyb_pin_BT_RXD) #define MICROPY_HW_UART6_RTS (pyb_pin_BT_RTS) #define MICROPY_HW_UART6_CTS (pyb_pin_BT_CTS) // I2C busses #define MICROPY_HW_I2C1_NAME "X" #define MICROPY_HW_I2C1_SCL (pyb_pin_X9) #define MICROPY_HW_I2C1_SDA (pyb_pin_X10) #define MICROPY_HW_I2C2_NAME "Y" #define MICROPY_HW_I2C2_SCL (pyb_pin_Y9) #define MICROPY_HW_I2C2_SDA (pyb_pin_Y10) // SPI busses #define MICROPY_HW_SPI1_NAME "X" #define MICROPY_HW_SPI1_NSS (pyb_pin_X5) #define MICROPY_HW_SPI1_SCK (pyb_pin_X6) #define MICROPY_HW_SPI1_MISO (pyb_pin_X7) #define MICROPY_HW_SPI1_MOSI (pyb_pin_X8) #define MICROPY_HW_SPI2_NAME "Y" #define MICROPY_HW_SPI2_NSS (pyb_pin_Y5) #define MICROPY_HW_SPI2_SCK (pyb_pin_Y6) #define MICROPY_HW_SPI2_MISO (pyb_pin_Y7) #define MICROPY_HW_SPI2_MOSI (pyb_pin_Y8) #define MICROPY_HW_SPI3_NSS (pyb_pin_W16) #define MICROPY_HW_SPI3_SCK (pyb_pin_W29) #define MICROPY_HW_SPI3_MISO (pyb_pin_W50) #define MICROPY_HW_SPI3_MOSI (pyb_pin_W46) // CAN busses #define MICROPY_HW_CAN1_NAME "X" #define MICROPY_HW_CAN1_TX (pyb_pin_X10) #define MICROPY_HW_CAN1_RX (pyb_pin_X9) // USRSW is not pulled, and pressing the button makes the input go low. #define MICROPY_HW_USRSW_PIN (pyb_pin_USR) #define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) #define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) #define MICROPY_HW_USRSW_PRESSED (0) // LEDs #define MICROPY_HW_LED_INVERTED (1) // LEDs are on when pin is driven low #define MICROPY_HW_LED1 (pyb_pin_LED_RED) #define MICROPY_HW_LED2 (pyb_pin_LED_GREEN) #define MICROPY_HW_LED3 (pyb_pin_LED_BLUE) #define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin)) #define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin)) // SD card #define MICROPY_HW_SDCARD_SDMMC (2) #define MICROPY_HW_SDCARD_CK (pyb_pin_SD_CK) #define MICROPY_HW_SDCARD_CMD (pyb_pin_SD_CMD) #define MICROPY_HW_SDCARD_D0 (pyb_pin_SD_D0) #define MICROPY_HW_SDCARD_D1 (pyb_pin_SD_D1) #define MICROPY_HW_SDCARD_D2 (pyb_pin_SD_D2) #define MICROPY_HW_SDCARD_D3 (pyb_pin_SD_D3) #define MICROPY_HW_SDCARD_DETECT_PIN (pyb_pin_SD_SW) #define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) #define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) #define MICROPY_HW_SDCARD_MOUNT_AT_BOOT (0) // USB config #define MICROPY_HW_USB_FS (1) #define MICROPY_HW_USB_HS (1) #define MICROPY_HW_USB_HS_IN_FS (1) #define MICROPY_HW_USB_MAIN_DEV (USB_PHY_HS_ID) // Bluetooth config #define MICROPY_HW_BLE_UART_ID (PYB_UART_6) #define MICROPY_HW_BLE_UART_BAUDRATE (115200) #define MICROPY_HW_BLE_UART_BAUDRATE_SECONDARY (3000000) /******************************************************************************/ // Bootloader configuration #define MBOOT_USB_AUTODETECT_PORT (1) #define MBOOT_FSLOAD (1) #define MBOOT_VFS_FAT (1) #define MBOOT_I2C_PERIPH_ID 1 #define MBOOT_I2C_SCL (pin_B8) #define MBOOT_I2C_SDA (pin_B9) #define MBOOT_I2C_ALTFUNC (4) #define MBOOT_SPIFLASH_ADDR (0x80000000) #define MBOOT_SPIFLASH_BYTE_SIZE (64 * 32 * 1024) #define MBOOT_SPIFLASH_LAYOUT "/0x80000000/64*32Kg" #define MBOOT_SPIFLASH_ERASE_BLOCKS_PER_PAGE (32 / 4) #define MBOOT_SPIFLASH_SPIFLASH (&spi_bdev.spiflash) #define MBOOT_SPIFLASH_CONFIG (&spiflash_config) #define MBOOT_SPIFLASH2_ADDR (0x90000000) #define MBOOT_SPIFLASH2_BYTE_SIZE (64 * 32 * 1024) #define MBOOT_SPIFLASH2_LAYOUT "/0x90000000/64*32Kg" #define MBOOT_SPIFLASH2_ERASE_BLOCKS_PER_PAGE (32 / 4) #define MBOOT_SPIFLASH2_SPIFLASH (&spi_bdev2.spiflash) #define MBOOT_SPIFLASH2_CONFIG (&spiflash2_config) #define MBOOT_BOARD_EARLY_INIT mboot_board_early_init void mboot_board_early_init(void);