/* * This file is part of the MicroPython project, http://micropython.org/ * * The MIT License (MIT) * * Copyright (c) 2017 Scott Shawcroft for Adafruit Industries * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. */ #include #include #include "boards/board.h" #include "supervisor/port.h" // ASF 4 #include "atmel_start_pins.h" #include "peripheral_clk_config.h" #include "hal/include/hal_delay.h" #include "hal/include/hal_flash.h" #include "hal/include/hal_gpio.h" #include "hal/include/hal_init.h" #include "hpl/gclk/hpl_gclk_base.h" #include "hpl/pm/hpl_pm_base.h" #ifdef SAMD21 #include "hri/hri_pm_d21.h" #endif #ifdef SAMD51 #include "hri/hri_rstc_d51.h" #endif #include "common-hal/analogio/AnalogIn.h" #include "common-hal/analogio/AnalogOut.h" #include "common-hal/audiobusio/PDMIn.h" #include "common-hal/audiobusio/I2SOut.h" #include "common-hal/audioio/AudioOut.h" #include "common-hal/busio/SPI.h" #include "common-hal/microcontroller/Pin.h" #include "common-hal/pulseio/PulseIn.h" #include "common-hal/pulseio/PulseOut.h" #include "common-hal/pulseio/PWMOut.h" #include "common-hal/ps2io/Ps2.h" #include "common-hal/rtc/RTC.h" #if CIRCUITPY_TOUCHIO_USE_NATIVE #include "common-hal/touchio/TouchIn.h" #endif #include "samd/cache.h" #include "samd/clocks.h" #include "samd/events.h" #include "samd/external_interrupts.h" #include "samd/dma.h" #include "shared-bindings/rtc/__init__.h" #include "reset.h" #include "supervisor/shared/safe_mode.h" #include "supervisor/shared/stack.h" #include "supervisor/shared/tick.h" #include "tusb.h" #if CIRCUITPY_GAMEPAD #include "shared-module/gamepad/__init__.h" #endif #if CIRCUITPY_GAMEPADSHIFT #include "shared-module/gamepadshift/__init__.h" #endif #include "shared-module/_pew/PewPew.h" extern volatile bool mp_msc_enabled; #if defined(SAMD21) && defined(ENABLE_MICRO_TRACE_BUFFER) // Stores 2 ^ TRACE_BUFFER_MAGNITUDE_PACKETS packets. // 7 -> 128 packets #define TRACE_BUFFER_MAGNITUDE_PACKETS 7 // Size in uint32_t. Two per packet. #define TRACE_BUFFER_SIZE (1 << (TRACE_BUFFER_MAGNITUDE_PACKETS + 1)) // Size in bytes. 4 bytes per uint32_t. #define TRACE_BUFFER_SIZE_BYTES (TRACE_BUFFER_SIZE << 2) __attribute__((__aligned__(TRACE_BUFFER_SIZE_BYTES))) uint32_t mtb[TRACE_BUFFER_SIZE] = {0}; #endif #if CALIBRATE_CRYSTALLESS static void save_usb_clock_calibration(void) { // If we are on USB lets double check our fine calibration for the clock and // save the new value if its different enough. SYSCTRL->DFLLSYNC.bit.READREQ = 1; uint16_t saved_calibration = 0x1ff; if (strcmp((char*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, "CIRCUITPYTHON1") == 0) { saved_calibration = ((uint16_t *) CIRCUITPY_INTERNAL_CONFIG_START_ADDR)[8]; } while (SYSCTRL->PCLKSR.bit.DFLLRDY == 0) { // TODO(tannewt): Run the mass storage stuff if this takes a while. } int16_t current_calibration = SYSCTRL->DFLLVAL.bit.FINE; if (abs(current_calibration - saved_calibration) > 10) { // Copy the full internal config page to memory. uint8_t page_buffer[NVMCTRL_ROW_SIZE]; memcpy(page_buffer, (uint8_t*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, NVMCTRL_ROW_SIZE); // Modify it. memcpy(page_buffer, "CIRCUITPYTHON1", 15); // First 16 bytes (0-15) are ID. Little endian! page_buffer[16] = current_calibration & 0xff; page_buffer[17] = current_calibration >> 8; // Write it back. // We don't use features that use any advanced NVMCTRL features so we can fake the descriptor // whenever we need it instead of storing it long term. struct flash_descriptor desc; desc.dev.hw = NVMCTRL; flash_write(&desc, (uint32_t) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, page_buffer, NVMCTRL_ROW_SIZE); } } #endif static void rtc_init(void) { #ifdef SAMD21 _gclk_enable_channel(RTC_GCLK_ID, GCLK_CLKCTRL_GEN_GCLK2_Val); RTC->MODE0.CTRL.bit.SWRST = true; while (RTC->MODE0.CTRL.bit.SWRST != 0) {} RTC->MODE0.CTRL.reg = RTC_MODE0_CTRL_ENABLE | RTC_MODE0_CTRL_MODE_COUNT32 | RTC_MODE0_CTRL_PRESCALER_DIV2; #endif #ifdef SAMD51 hri_mclk_set_APBAMASK_RTC_bit(MCLK); RTC->MODE0.CTRLA.bit.SWRST = true; while (RTC->MODE0.SYNCBUSY.bit.SWRST != 0) {} RTC->MODE0.CTRLA.reg = RTC_MODE0_CTRLA_ENABLE | RTC_MODE0_CTRLA_MODE_COUNT32 | RTC_MODE0_CTRLA_PRESCALER_DIV2 | RTC_MODE0_CTRLA_COUNTSYNC; #endif RTC->MODE0.INTENSET.reg = RTC_MODE0_INTENSET_OVF; // Set all peripheral interrupt priorities to the lowest priority by default. for (uint16_t i = 0; i < PERIPH_COUNT_IRQn; i++) { NVIC_SetPriority(i, (1UL << __NVIC_PRIO_BITS) - 1UL); } // Bump up the rtc interrupt so nothing else interferes with timekeeping. NVIC_SetPriority(RTC_IRQn, 0); #ifdef SAMD21 NVIC_SetPriority(USB_IRQn, 1); #endif #ifdef SAMD51 NVIC_SetPriority(USB_0_IRQn, 1); NVIC_SetPriority(USB_1_IRQn, 1); NVIC_SetPriority(USB_2_IRQn, 1); NVIC_SetPriority(USB_3_IRQn, 1); #endif NVIC_ClearPendingIRQ(RTC_IRQn); NVIC_EnableIRQ(RTC_IRQn); #if CIRCUITPY_RTC rtc_reset(); #endif } safe_mode_t port_init(void) { #if defined(SAMD21) // Set brownout detection to ~2.7V. Default from factory is 1.7V, // which is too low for proper operation of external SPI flash chips (they are 2.7-3.6V). // Disable while changing level. SYSCTRL->BOD33.bit.ENABLE = 0; SYSCTRL->BOD33.bit.LEVEL = 39; // 2.77V with hysteresis off. Table 37.20 in datasheet. SYSCTRL->BOD33.bit.ENABLE = 1; #ifdef ENABLE_MICRO_TRACE_BUFFER REG_MTB_POSITION = ((uint32_t) (mtb - REG_MTB_BASE)) & 0xFFFFFFF8; REG_MTB_FLOW = (((uint32_t) mtb - REG_MTB_BASE) + TRACE_BUFFER_SIZE_BYTES) & 0xFFFFFFF8; REG_MTB_MASTER = 0x80000000 + (TRACE_BUFFER_MAGNITUDE_PACKETS - 1); #else // Triple check that the MTB is off. Switching between debug and non-debug // builds can leave it set over reset and wreak havok as a result. REG_MTB_MASTER = 0x00000000 + 6; #endif #endif #if defined(SAMD51) // Set brownout detection to ~2.7V. Default from factory is 1.7V, // which is too low for proper operation of external SPI flash chips (they are 2.7-3.6V). // Disable while changing level. SUPC->BOD33.bit.ENABLE = 0; SUPC->BOD33.bit.LEVEL = 200; // 2.7V: 1.5V + LEVEL * 6mV. SUPC->BOD33.bit.ENABLE = 1; // MPU (Memory Protection Unit) setup. // We hoped we could make the QSPI region be non-cachable with the MPU, // but the CMCC doesn't seem to pay attention to the MPU settings. // Leaving this code here disabled, // because it was hard enough to figure out, and maybe there's // a mistake that could make it work in the future. #if 0 // Designate QSPI memory mapped region as not cachable. // Turn off MPU in case it is on. MPU->CTRL = 0; // Configure region 0. MPU->RNR = 0; // Region base: start of QSPI mapping area. // QSPI region runs from 0x04000000 up to and not including 0x05000000: 16 megabytes MPU->RBAR = QSPI_AHB; MPU->RASR = 0b011 << MPU_RASR_AP_Pos | // full read/write access for privileged and user mode 0b000 << MPU_RASR_TEX_Pos | // caching not allowed, strongly ordered 1 << MPU_RASR_S_Pos | // sharable 0 << MPU_RASR_C_Pos | // not cachable 0 << MPU_RASR_B_Pos | // not bufferable 0b10111 << MPU_RASR_SIZE_Pos | // 16MB region size 1 << MPU_RASR_ENABLE_Pos // enable this region ; // Turn off regions 1-7. for (uint32_t i = 1; i < 8; i ++) { MPU->RNR = i; MPU->RBAR = 0; MPU->RASR = 0; } // Turn on MPU. Turn on PRIVDEFENA, which defines a default memory // map for all privileged access, so we don't have to set up other regions // besides QSPI. MPU->CTRL = MPU_CTRL_PRIVDEFENA_Msk | MPU_CTRL_ENABLE_Msk; #endif samd_peripherals_enable_cache(); #endif #ifdef SAMD21 hri_nvmctrl_set_CTRLB_RWS_bf(NVMCTRL, 2); _pm_init(); #endif #if CALIBRATE_CRYSTALLESS uint32_t fine = DEFAULT_DFLL48M_FINE_CALIBRATION; // The fine calibration data is stored in an NVM page after the text and data storage but before // the optional file system. The first 16 bytes are the identifier for the section. if (strcmp((char*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, "CIRCUITPYTHON1") == 0) { fine = ((uint16_t *) CIRCUITPY_INTERNAL_CONFIG_START_ADDR)[8]; } clock_init(BOARD_HAS_CRYSTAL, fine); #else // Use a default fine value clock_init(BOARD_HAS_CRYSTAL, DEFAULT_DFLL48M_FINE_CALIBRATION); #endif rtc_init(); init_shared_dma(); // Reset everything into a known state before board_init. reset_port(); #ifdef SAMD21 if (PM->RCAUSE.bit.BOD33 == 1 || PM->RCAUSE.bit.BOD12 == 1) { return BROWNOUT; } #endif #ifdef SAMD51 if (RSTC->RCAUSE.bit.BODVDD == 1 || RSTC->RCAUSE.bit.BODCORE == 1) { return BROWNOUT; } #endif if (board_requests_safe_mode()) { return USER_SAFE_MODE; } return NO_SAFE_MODE; } void reset_port(void) { reset_sercoms(); #if CIRCUITPY_AUDIOIO audio_dma_reset(); audioout_reset(); #endif #if CIRCUITPY_AUDIOBUSIO i2sout_reset(); //pdmin_reset(); #endif #if CIRCUITPY_TOUCHIO && CIRCUITPY_TOUCHIO_USE_NATIVE touchin_reset(); #endif eic_reset(); #if CIRCUITPY_PULSEIO pulsein_reset(); pulseout_reset(); pwmout_reset(); #endif #if CIRCUITPY_ANALOGIO analogin_reset(); analogout_reset(); #endif reset_gclks(); #if CIRCUITPY_GAMEPAD gamepad_reset(); #endif #if CIRCUITPY_GAMEPADSHIFT gamepadshift_reset(); #endif #if CIRCUITPY_PEW pew_reset(); #endif reset_event_system(); reset_all_pins(); // Output clocks for debugging. // not supported by SAMD51G; uncomment for SAMD51J or update for 51G // #ifdef SAMD51 // gpio_set_pin_function(PIN_PA10, GPIO_PIN_FUNCTION_M); // GCLK4, D3 // gpio_set_pin_function(PIN_PA11, GPIO_PIN_FUNCTION_M); // GCLK5, A4 // gpio_set_pin_function(PIN_PB14, GPIO_PIN_FUNCTION_M); // GCLK0, D5 // gpio_set_pin_function(PIN_PB15, GPIO_PIN_FUNCTION_M); // GCLK1, D6 // #endif #if CALIBRATE_CRYSTALLESS if (tud_cdc_connected()) { save_usb_clock_calibration(); } #endif } void reset_to_bootloader(void) { _bootloader_dbl_tap = DBL_TAP_MAGIC; reset(); } void reset_cpu(void) { reset(); } supervisor_allocation* port_fixed_stack(void) { return NULL; } uint32_t *port_stack_get_limit(void) { return &_ebss; } uint32_t *port_stack_get_top(void) { return &_estack; } uint32_t *port_heap_get_bottom(void) { return port_stack_get_limit(); } uint32_t *port_heap_get_top(void) { return port_stack_get_top(); } // Place the word to save 8k from the end of RAM so we and the bootloader don't clobber it. #ifdef SAMD21 uint32_t* safe_word = (uint32_t*) (HMCRAMC0_ADDR + HMCRAMC0_SIZE - 0x2000); #endif #ifdef SAMD51 uint32_t* safe_word = (uint32_t*) (HSRAM_ADDR + HSRAM_SIZE - 0x2000); #endif void port_set_saved_word(uint32_t value) { *safe_word = value; } uint32_t port_get_saved_word(void) { return *safe_word; } // TODO: Move this to an RTC backup register so we can preserve it when only the BACKUP power domain // is enabled. static volatile uint64_t overflowed_ticks = 0; static volatile bool _ticks_enabled = false; void RTC_Handler(void) { uint32_t intflag = RTC->MODE0.INTFLAG.reg; if (intflag & RTC_MODE0_INTFLAG_OVF) { RTC->MODE0.INTFLAG.reg = RTC_MODE0_INTFLAG_OVF; // Our RTC is 32 bits and we're clocking it at 16.384khz which is 16 (2 ** 4) subticks per // tick. overflowed_ticks += (1L<< (32 - 4)); #ifdef SAMD51 } else if (intflag & RTC_MODE0_INTFLAG_PER2) { RTC->MODE0.INTFLAG.reg = RTC_MODE0_INTFLAG_PER2; // Do things common to all ports when the tick occurs supervisor_tick(); #endif } else if (intflag & RTC_MODE0_INTFLAG_CMP0) { // Clear the interrupt because we may have hit a sleep and _ticks_enabled RTC->MODE0.INTFLAG.reg = RTC_MODE0_INTFLAG_CMP0; #ifdef SAMD21 if (_ticks_enabled) { // Do things common to all ports when the tick occurs. supervisor_tick(); // Check _ticks_enabled again because a tick handler may have turned it off. if (_ticks_enabled) { port_interrupt_after_ticks(1); } } #endif #ifdef SAMD51 RTC->MODE0.INTENCLR.reg = RTC_MODE0_INTENCLR_CMP0; #endif } } static uint32_t _get_count(void) { #ifdef SAMD51 while ((RTC->MODE0.SYNCBUSY.reg & (RTC_MODE0_SYNCBUSY_COUNTSYNC | RTC_MODE0_SYNCBUSY_COUNT)) != 0) {} #endif #ifdef SAMD21 while (RTC->MODE0.STATUS.bit.SYNCBUSY != 0) {} #endif return RTC->MODE0.COUNT.reg; } uint64_t port_get_raw_ticks(uint8_t* subticks) { uint32_t current_ticks = _get_count(); if (subticks != NULL) { *subticks = (current_ticks % 16) * 2; } return overflowed_ticks + current_ticks / 16; } // Enable 1/1024 second tick. void port_enable_tick(void) { #ifdef SAMD51 // PER2 will generate an interrupt every 32 ticks of the source 32.768 clock. RTC->MODE0.INTENSET.reg = RTC_MODE0_INTENSET_PER2; #endif #ifdef SAMD21 _ticks_enabled = true; port_interrupt_after_ticks(1); #endif } // Disable 1/1024 second tick. void port_disable_tick(void) { #ifdef SAMD51 RTC->MODE0.INTENCLR.reg = RTC_MODE0_INTENCLR_PER2; #endif #ifdef SAMD21 _ticks_enabled = false; RTC->MODE0.INTENCLR.reg = RTC_MODE0_INTENCLR_CMP0; #endif } void port_interrupt_after_ticks(uint32_t ticks) { uint32_t current_ticks = _get_count(); if (ticks > 1 << 28) { // We'll interrupt sooner with an overflow. return; } RTC->MODE0.COMP[0].reg = current_ticks + (ticks << 4); RTC->MODE0.INTFLAG.reg = RTC_MODE0_INTFLAG_CMP0; RTC->MODE0.INTENSET.reg = RTC_MODE0_INTENSET_CMP0; } void port_sleep_until_interrupt(void) { #ifdef SAMD51 // Clear the FPU interrupt because it can prevent us from sleeping. if (__get_FPSCR() & ~(0x9f)) { __set_FPSCR(__get_FPSCR() & ~(0x9f)); (void) __get_FPSCR(); } #endif __WFI(); } /** * \brief Default interrupt handler for unused IRQs. */ __attribute__((used)) void HardFault_Handler(void) { #ifdef ENABLE_MICRO_TRACE_BUFFER // Turn off the micro trace buffer so we don't fill it up in the infinite // loop below. REG_MTB_MASTER = 0x00000000 + 6; #endif reset_into_safe_mode(HARD_CRASH); while (true) { asm("nop;"); } }