The current ST HAL does not support reading the extended CSD so cannot
correctly detect the capacity of high-capacity cards. As a workaround, the
capacity can be forced via the MICROPY_HW_MMCARD_LOG_BLOCK_NBR config
option.
Signed-off-by: Damien George <damien@micropython.org>
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.
Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
With GCC 11 there is now a warning about array bounds of OTP-mac, due to
the OTP being a literal address.
Signed-off-by: Damien George <damien@micropython.org>
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
Support for C++ was added in 97960dc7de but
that commit didn't include the C++ exception handling table in the binary
firmware image. This commit fixes that.
Signed-off-by: Damien George <damien@micropython.org>
Mboot builds do not use the external SPI flash in caching mode, and
explicitly disabling it saves RAM and a small bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.
Signed-off-by: Damien George <damien@micropython.org>
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
This change has the following effects:
- Reduces the resolution of the RTC sub-second counter from 30.52us to
122.07us.
- Allows RTC.calibration() to now support positive values (as well as
negative values).
- Reduces VBAT current consumption in standby mode by a small amount.
For general purpose use 122us resolution of the sub-second counter is
good enough, and the benefits of full range calibration and minor reduction
in VBAT consumption are worth the change.
Entering a bootloader (ST system bootloader, or custom mboot) from software
by directly branching to it is not reliable, and the reliability of it
working can depend on the peripherals that were enabled by the application
code. It's also not possible to branch to a bootloader if the WDT is
enabled (unless the bootloader has specific provisions to feed the WDT).
This patch changes the way a bootloader is entered from software by first
doing a complete system reset, then branching to the desired bootloader
early on in the start-up process. The top two words of RAM (of the stack)
are reserved to store flags indicating that the bootloader should be
entered after a reset.
Previously the end of the heap was the start (lowest address) of the stack.
With the changes in this commit these addresses are now independent,
allowing a board to place the heap and stack in separate locations.
Damien George
MikeTeachman
Jim Mussared
Mike Causer
iabdalkader
Damien George
Chris Mason