The range is 1MHz - 48 MHz. Note that below 8 MHz there is no USB support.
The frequency will be set to an integer fraction of 48 MHz. And after
changing the frequency, the peripherals like PWM, UART, I2C, SPI have to be
reconfigured.
Current consumption e.g. of the Seeed Xiao board at 1 MHz is about 1.5 mA,
mostly caused by the on-board LED (green LED with 1k resistor at 3.3V).
The value given for machine.freq(f) is extend to the range of 1_000_000 to
200_000_000. Frequencies below 48 MHz will be forced to an integer
fraction of 48 MHz. At frequencies below 8 MHz USB is switched off. The
power consumption e.g. of ADAFRUIT_ITSYBITSY_M4_EXPRESS drops to about
1.5 mA at 1 MHz.
Since the peripheral frequency is dropped as well, timing e.g. of PWM,
UART, I2C and SPI is affected and frequency/baud rate has to set again
after a frequency change below 48 MHz.
In order for v1.19.1 to load a .mpy, the formerly-feature-flags which are
now used for the sub-version must be zero.
The sub-version is only used to indicate a native version change, so it
should be zero when emitting bytecode-only .mpy files.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prevents double-precision floats being enabled on 32-bit architectures
where they will not fit into the mp_obj_t encoding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
They are much slower than NIST (SECP) curves and shouldn't be needed.
Reduces rp2 PICO_W firmware by 1328 bytes.
Thanks to @Carglglz for the information.
Signed-off-by: Damien George <damien@micropython.org>
Curve25519 arithmetic is supported in mbedtls, but it's not used for TLS.
So there's no need to have this option enabled.
Reduces rp2 PICO_W firmware by 2440 bytes.
Thanks to @Carglglz for the information.
Signed-off-by: Damien George <damien@micropython.org>
This is necessary to access sites that only support these protocols.
The rp2 port already has ECDH enabled, so this just adds ECDSA there. The
other ports now gain both ECDH and ECDSA. The code size increase is:
- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS
This is obviously a large increase in code size. But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet. For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.
Signed-off-by: Damien George <damien@micropython.org>
The following multi-tests pass (eg with PYBD_SF6+LEGO_HUB_NO6):
ble_gap_advertise.py
ble_gap_connect.py
ble_gap_device_name.py
ble_gattc_discover_services.py
ble_gatt_data_transfer.py
perf_gatt_char_write.py
perf_gatt_notify.py
stress_log_filesystem.py
These are the same tests that passed prior to this BTstack update.
Also tested on the unix port using H4 transport.
Signed-off-by: Damien George <damien@micropython.org>
Since there is only one flag, we don't need to use a bitfield in vstr_t.
Compilers emit extra instructions to access a bitfield, so this should
reduce the binary size a small amount.
Signed-off-by: David Lechner <david@pybricks.com>
This makes it so that all a port needs to do is set the relevant variables
and "include extmod.mk" and doesn't need to worry about adding anything to
OBJ, CFLAGS, SRC_QSTR, etc.
Make all extmod variables (src, flags, etc) private to extmod.mk.
Also move common/shared, extmod-related fragments (e.g. wiznet, cyw43,
bluetooth) into extmod.mk.
Now that SRC_MOD, CFLAGS_MOD, CXXFLAGS_MOD are unused by both extmod.mk
(and user-C-modules in a previous commit), remove all uses of them from
port makefiles.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This applies to nimble, btstack, axtls, mbedtls, lwip.
Rather than having the ports individually manage GIT_SUBMODULES for these
components, make extmod.mk append them when the relevant feature is
enabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This conflicts with the triple-usage of these variables for user-C-modules
and extmod source.
For CFLAGS_MOD, just use CFLAGS directly. For SRC, use SRC_C directly as
the relevant files are all guarded by the preprocessor anyway.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Removes the need for the port to add anything to OBJS or SRC_QSTR.
Also makes it possible for user-C-modules to differentiate between code
that should be processed for QSTR vs other files (e.g. helpers and
libraries).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Gives the absolute path to the unix micropython binary.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
Only intended to be used on Unix and other "OS" ports. Matches CPython.
This should give the absolute path to the executing binary.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
This check used to just show the regular expression that failed to match,
but the rules are pretty subtle and hard to interpret from the regular
expression alone.
Add some basic checks for the main things that go wrong:
- Missing capitalisation.
- Missing full-stop.
- Missing path.
- Single-word subject.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The "signed-off" check assumes that the Signed-off-by: line is the last,
but there may me many lines of comments after this.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It now prints lines like:
Pin("D9", mode=IN, pull=PULL_UP, GPIO=PA07)
or
LED("LED")
showing for consistency the names as given in pins.csv. For pins, the GPIO
numer is printed as well for a reference.
robert-hh
Jim Mussared
Damien George
iabdalkader
David Lechner