The error message for creating an I2S object on the rp2040 platform
in CircuitPython can be misleading when the word_select and data pins
are not sequential. This change updates the error message to provide
clearer guidance by specifying "GPIO pins" instead of just "pins".
The revised message now reads:
ValueError: Bit clock and word select must be sequential GPIO pins
Closes#8058
Signed-off-by: Sumitra Sharma <sumitraartsy@gmail.com>
Currently on rp2 the time.time_ns() function has only seconds resolution.
This commit makes it have microsecond resolution, by using the output of
time_us_64() instead of the RTC.
Tested that it does not drift from the RTC over long periods of time.
Signed-off-by: Damien George <damien.p.george@gmail.com>
No other network-enabled board has urllib.urequest frozen in to the
firmware, and esp8266 is relatively low on flash, so remove this module.
And (u)requests is already included by bundle-networking.
Signed-off-by: Damien George <damien@micropython.org>
Also remove corresponding commented line from esp8266/boards/manifest.py.
It doesn't have enough flash to have this frozen by default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
Allows using gdb, addr2line, etc. on a "release" ELF file.
No impact to .bin or .uf2 size, only the .elf will get bigger.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The current code assumes all I2Cs are on the same peripheral bus, which is
not true for I2C4 and the same goes for the clock enable code.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The IDF-provided version of TinyUSB defaults to Espressif's standard
VID:PID unless specific sdkconfig options are present. The numbers
already defined for the CUSTOM_* config options were ignored otherwise.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
This removes the duplicate code in cyw43, esp32, esp8266 that implements
the same logic as network.hostname.
Renames the `mod_network_hostname` (where we store the hostname value in
`.data`) to `mod_network_hostname_data` to make way for calling the shared
function `mod_network_hostname`.
And uses memcpy for mod_network_hostname_data, because the length of source
is already known and removes reliance on string data being null-terminated.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes from the previous limit of 15 characters. Although DHCP and
mDNS allow for up to 63, ESP32 and ESP8266 only allow 32, so this seems
like a reasonable limit to enforce across all ports (and avoids wasting the
additional memory).
Also clarifies that `MICROPY_PY_NETWORK_HOSTNAME_MAX_LEN` does not include
the null terminator (which was unclear before).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By clearing the tamper bits and enabling access to the registers for all
code, just in case that this was set. It keeps the clock running on
battery and the calibration setting.
Signed-off-by: robert-hh <robert@hammelrath.com>
Not all boards or BLE extensions have the flow control signals for BLE
available at suitable pins. Actually none of the Adafruit extensions
match for flow control.
For consistency with the previous behaviour it is enabled by default.
Signed-off-by: robert-hh <robert@hammelrath.com>
Commit 552b0bbe12 did not define
MICROPY_PY_MACHINE_SDCARD properly, and thus building the firmware failed.
Signed-off-by: robert-hh <robert@hammelrath.com>
Dan Halbert
Dan Halbert
Scott Shawcroft
Taiki Komoda
Sumitra Sharma
Tirtharaj Sinha
Damien George
Glenn Moloney
Angus Gratton
iabdalkader
Luca Burelli
Jim Mussared
Jeff Epler
Wanlin Wang
vsfos
robert-hh
Paint Your Dragon