* Fixes#6221 - C3 hang on `import wifi`. Enabling the WiFi PHY was
disabling USB. Now boards that use it set CONFIG_ESP_PHY_ENABLE_USB
explicitly.
* Fixes#6655 - Allows pasting into the web serial page. Fixes reading
more than 0xf bytes at a time.
* Fixes#6653 - Fixes web socket encoding of payloads >125 bytes. Can
happen when printing a long string.
* Fixes C3 responsiveness when waiting for key to enter REPL. (It
now correctly stops sleeping.)
* Disables title bar updates when in raw REPL. Related to #6548.
* Adds version to title bar.
It had a tight 5ms timeout before that caused some characters to
drop. Now the wait is longer and reset after a successful transmit.
This follows what MicroPython does.
Fixes#6220
1. Run the socket select task at the same priority as CP. This is
needed because it queues up the background work. Without it, CP
needed to sleep to let the lower priority task go.
2. Close the active socket on disconnect. This prevents looping
over a disconnected but not closed socket.
Fixes#6610. Fixes#6613
- define CIRCUITPY_BUILD_EXTENSIONS to predefined values
- set CIRCUITPY_BUILD_EXTENSIONS in port and board config
- reuse the support matrix "get_settings_from_makefile" to get it
- move the existing port and board specific values
- remove the C3 specific board values because it's not the default
- update build_release_files.py to use get_settings_from_makefile
- Based on espressif/nimble's blecent example code. Confirms that the characteristic is not empty before trying to catalogue its descriptors.
- Running ble_gattc_disc_all_dscs on empty (no length) characteristics fails with the (not-very-informative) BLE_HS_EINVAL error if this check is not performed.
.. this makes reconnecting without a full reset not work.
Because this works on other generations of the esp32 (c2, c3, etc),
apply this behavior only to esp32.
After this change, it's possible to connect multiple times to wifi in
different runs of code.py or the repl after soft rebooting.
Format:
CIRCUITPY_BLE_NAME = My BLE Board
- the length is limited to 31 characters
- for the NRF version it repeatedly truncates the name if it's too long
- the ESP version defaults to "nimble" if the name is too long
rather than setting the heap size statically, micropython allocates
the biggest contiguous chunk possible, but in no event more than half the
total internal sram. On esp32 this gives 123728 bytes of `gc.mem_free`
in the repl.
Also, change error handling so that the esp-idf error number
is shown in the traceback in the case of an error.
This allows scanning & connecting to work. I didn't try requests yet.
esp32 places the psram start at SOC_EXTRAM_DATA_LOW and it can extend
up to SOC_EXTRAM_DATA_SIZE. This is different than esp32-s2 and later,
which place the end at EXTRAM_DATA_HIGH and the limitation of
SOC_EXTRAM_DATA_SIZE was not previously identified as important.
Additionally, the esp32 has a reserved area within himem which was
not being accounted for.
With this change, the Feather ESP32 V2 feather can be used via thonny,
and the other "quick memory corruption tests" I was performing
also all succeed instead of failing.
Before this change, the incorrect address being used for spiram was
0x3fa00000..0x3fc00000 (2MiB). Now, it's 0x3f800000..0x3f9c0000 (1.75MiB)
due to the reserved area and the changed start address.
This is intended to be a no-effect change for other espressif chips besides
original esp32.
addr2line can show information about how functions were inlined,
including function names
Typical new output:
```
0x400dec57: mp_obj_get_type at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:68
(inlined by) mp_obj_print_helper at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:133
(inlined by) mp_obj_print_helper at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:114
0x400e1a25: fun_builtin_1_call at /home/jepler/src/circuitpython/ports/espressif/../../py/objfun.c:75
0x400dd016: mp_call_function_n_kw at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:665
0x400eac99: mp_execute_bytecode at /home/jepler/src/circuitpython/ports/espressif/../../py/vm.c:936
0x400e1ae9: fun_bc_call at /home/jepler/src/circuitpython/ports/espressif/../../py/objfun.c:297 (discriminator 4)
0x400dd016: mp_call_function_n_kw at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:665
0x400dd03a: mp_call_function_0 at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:638
0x40117c03: parse_compile_execute at /home/jepler/src/circuitpython/ports/espressif/../../shared/runtime/pyexec.c:146
0x4011800d: pyexec_friendly_repl at /home/jepler/src/circuitpython/ports/espressif/../../shared/runtime/pyexec.c:734
0x400eeded: run_repl at /home/jepler/src/circuitpython/ports/espressif/../../main.c:823
(inlined by) main at /home/jepler/src/circuitpython/ports/espressif/../../main.c:922
0x400ef5e3: app_main at /home/jepler/src/circuitpython/ports/espressif/supervisor/port.c:410
0x401bb461: main_task at /home/jepler/src/circuitpython/ports/espressif/build-adafruit_feather_esp32_v2/esp-idf/../../esp-idf/components/freertos/port/port_common.c:141
```
