This adds a check to make sure that SDA and SCL are in a sane condition
before starting any I2C operation. If they are not it tries to rectify it,
and then returns an error code if unable to do so.
on specific SCK/MOSI/MISO pins, the `common_hal_busio_spi_construct`
method always skip miso pins which will lead to a `invalid pin`
exception when SPI initilized
In my testing, the feather bluefruit can do 12 voices at 48kHz!
This is a simple case (no LFOs, no ring modulation) so other situations might
require a lower sample rate, fewer voices, or both.
The sound is a little artifacty & low-fi but I think that's down to the speaker
& use of PWM instead of I2S.
and re-organize so that esp32 s2/s3 don't do as much at reset
.. it's not necessary (because most data is in esp-idf managed memory)
and doing this saves me from having to debug why reconstruct isn't working
properly on that platform.
This needs to be tested on other platforms again before being merged!
tested:
* board.LED
* neopixel as status LED
* i2c scan finds lis3dh sensor
* psram capacity
not tested:
* rgb matrix o_O
* the gpio pins
Introduce new `board` properties for matrixportal-style boards:
* MTX_COMMON
* MTX_ADDRESS
These are intended to simplify use of the RGBMatrix constructor:
```py
matrix = RGBMatrix(..., addr_pins=MTX_ADDRESS[:3], **MTX_COMMON)
```
removing the need for sending in the following individual parameters:
* rgb_pins
* clock_pin
* latch_pin
* output_enable_pins
and making construction of a 16/32/64-row display easy by slicing a tuple
of all address pins rather than writing out the individual pins. If it
works out it'll be ported back to the matrixportal m4 as well.
ESP32-S3 defines two additional general use pins in
ports/espressif/peripherals/esp32s3/pins.h, for which
support is missing in the microcontroller module HAL.
This prevents running into the pins that cannot be reset. On 1011
it was off by one pin that isn't attached to the package. So,
having the USB pins forbidden prevented resetting to a NULL address.
Fixes#7952
esp_ping_new_session can fail, particularly if ping is called quickly
many times in succession.
This is because `esp_ping_new_session` has to do a bunch of stuff
including creating a task and a socket. Calling `esp_ping_delete_session`
doesn't clean up these resources immediately. Instead, it signals the
task to clean up resources and exit 'soon', but 'soon' is defined as 1
second.
When the calls are frequent, the in-use sockets and tasks fill up
available slots—I didn't actually check which resource gets used
up first.
With this change, the ping call will raise an exception instead of
continuing with a call to esp_ping_start that crashes.
Closes#5980 based on my testing on an ESP32S3-N8R2.
The internal flash cache wasn't being properly used, because
`write_blocks` unconditionally performed the flash write.
Fixing this so that the write's not done until `internal_flash_flush`
fixes the problem in my test program with i2sout & synthio.
as a future optimization, `flash_read_blocks` could learn to read out
of the cache, but that's probably not super important.
This class allows much more expressive sound synthesis:
* tremolo & vibrato
* arbitrary frequency
* different evelope & waveform per note
* all properties dynamically settable from Python code
This adds a script to generate the peripherals files (except clock).
It adds support for the 1015, 1020, 1040, and 1050 EVKs.
Some work was started on 1176 but it isn't working. So, the board
def is in a separate branch.
Fixes#3521. Fixes#2477.
Since c80e7c14e6 changed the GC heap to use
all unused RAM, there is no longer any RAM available for the traditional C
heap (which is not used by default in MicroPython but may be used by C
extensions). This commit adds a provision for a board to reserve RAM for
the C heap, by defining MICROPY_C_HEAP_SIZE.
Signed-off-by: Damien George <damien@micropython.org>
The previous code worked on ESP32 but not ESP32-S3. All the IDF (v4.4.3)
examples call rmt_set_tx_loop_mode before rmt_write_items, so make that
change here.
Signed-off-by: Damien George <damien@micropython.org>
- Use HCI_TRACE macro consistently.
- Use the same colour formatting.
- Add a tool to convert to .pcap for Wireshark.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This adds a mechanism to track a pending notify/indicate operation that
is deferred due to the send buffer being full. This uses a tracked alloc
that is passed as the content arg to the callback.
This replaces the previous mechanism that did this via the global pending
op queue, shared with client read/write ops.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Makes gatts_notify and gatts_indicate work in the same way: by default they
send the DB value, but you can manually override the payload.
In other words, makes gatts_indicate work the same as gatts_notify.
Note: This removes support for queuing notifications and indications on
btstack when the ACL buffer is full. This functionality will be
reimplemented in a future commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Spotted the Cosmo_pico port on circuitpython.org which is the same class of device as the Pimoroni PICO dv so I'm switching the VID/PID to use the Raspberry Pi owned values rather than the Adafruit values just as the Como device uses.
Don't idle from main if we scheduled an interrupt for 0 ticks in
the future.
Have RP2040 detect wakes that happen between setting the timer and
the idle call.
Fixes#7361
The Wio Terminal includes a RealTek RTL8720D as a companion to the main chip to provide WiFi and Bluetooth capabilities via eRPC over a UART connection. The WIO Terminal schematic labels some pins as the RXD/TXD for the UART, and that was captured in the board definition for CircuitPython. However, these pins may be used for logging in another mode, but they are not the main pins used to communicate with the RTL chip. The correct configuration is RX on PC24/pad 2 and TX on PB24/pad 0 of SERCOM 0. The comments on the pin definitions now reflect this situation, for anyone trying to get the WiFi/BLE to work on the Wio Terminal.
This commit adds support for the `timeout` keyword argument to machine.I2C
on the rp2 port, following how it's done on other ports.
The main motivation here is avoid the interpreter crashing due to infinite
loops when SDA is stuck low, which is quite common if the board gets reset
while reading from an I2C device.
A default timeout of 50ms is chosen because it's consistent with:
- Commit a707fe50b0 which used a timeout of
50,000us for zero-length writes on the rp2 port.
- The machine.SoftI2C class which uses 50,000us as the default timeout.
- The stm32 port's hardware I2C, which uses 50,000us for
I2C_POLL_DEFAULT_TIMEOUT_US.
This commit also fixes the default timeout on the esp32 port to be
consistent with the above, and updates the documentation for machine.I2C to
document this keyword argument.
PicoDVI in CP support 640x480 and 800x480 on Feather DVI, Pico and
Pico W. 1 and 2 bit grayscale are full resolution. 8 and 16 bit
color are half resolution.
Memory layout is modified to give the top most 4k of ram to the
second core. Its MPU is used to prevent flash access after startup.
The port saved word is moved to a watchdog scratch register so that
it doesn't get overwritten by other things in RAM.
Right align status bar and scroll area. This normally gives a few
pixels of padding on the left hand side and improves the odds it is
readable in a case. Fixes#7562
Fixes c stack checking. The length was correct but the top was being
set to the current stack pointer instead of the correct top.
Fixes#7643
This makes Bitmap subscr raise IndexError instead of ValueError
when the index arguments are wrong.
Doing a squash merge to avoid having the `slc_cli_linux` .zip files in the history. They were added in one commit and removed and replaced with a submodule in another.
* Initial commit for xg24
* Fix SLC issue
* Fix SLC extract fail
* Change board's name
* Correct spelling of code
Build immediately after slc generate
* Remove VID and PID
* Change creator and creation id
* Apply new creator_id and creation_id
* Update makefile, error message, mcu_processor function
* Update mpconfigboard.mk
* Update Board extensions, PORT_DEPS
* Update makefile
* Add exclude_patterns
* Show java, jinja2 version
* Show path for debugging CI
* Add requirements-dev for slc
* Add PATH slc_cli
* Update background function
* Add jinja2 PATH
* Show PATH
* Update jinja2 path
* Update jinja2 path
* Update jinja2 path
* Update jinja2 path
* Change slc folder
* Change markupsafe folder
* Add symbolic link for slc
* Update makefile
* Update makefile
* Update MX25R3235F.toml from submodule nvm.toml
* alphabetize the list
* Remove slc_cli_linux folder
* Update slc_cli submodule
---------
Co-authored-by: Chat Nguyen <cvnguyen@silabs.com>
Co-authored-by: silabs-ChatNguyen <chat.nguyen@silabs.com>
Co-authored-by: silabs-ChatNguyen <126220343+silabs-ChatNguyen@users.noreply.github.com>
Noah Axon
Dan Halbert
Dan Halbert
Scott Shawcroft
paul
Phil Underwood
leosun
Kamil Tomaszewski
Jeff Epler
Melissa LeBlanc-Williams
Seon Rozenblum
Mario Bodemann
applecuckoo
applecuckoo
Pierre Constantineau
tomiahola
hyx0329
phamhuyvn
David Sullivan
David Sullivan
Christopher Hoover
rcarteraz
Bill Sideris
silabs-ChatNguyen
anecdata
Neradoc
Eric Rong
Bojan Potočnik
Alex Sirota
RetiredWizard
Kattni
Liz
Bernhard Bablok
Damien George
IcedRooibos
Jim Mussared
David Glaude
George White
David (Pololu)
Milind
CDarius
Ted Hess
silabs-BelaV