This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
When := is used in a comprehension the target variable is bound to the
parent scope, so it's either a global or a nonlocal. Prior to this commit
that was handled by simply using the parent scope's id_info for the
target variable. That's completely wrong because it uses the slot number
for the parent's Python stack to store the variable, rather than the slot
number for the comprehension. This will in most cases lead to incorrect
behaviour or memory faults.
This commit fixes the scoping of the target variable by explicitly
declaring it a global or nonlocal, depending on whether the parent is the
global scope or not. Then the id_info of the comprehension can be used to
access the target variable. This fixes a lot of cases of using := in a
comprehension.
Code size change for this commit:
bare-arm: +0 +0.000%
minimal x86: +0 +0.000%
unix x64: +152 +0.019% standard
stm32: +96 +0.024% PYBV10
cc3200: +96 +0.052%
esp8266: +196 +0.028% GENERIC
esp32: +156 +0.010% GENERIC[incl +8(data)]
mimxrt: +96 +0.027% TEENSY40
renesas-ra: +88 +0.014% RA6M2_EK
nrf: +88 +0.048% pca10040
rp2: +104 +0.020% PICO
samd: +88 +0.033% ADAFRUIT_ITSYBITSY_M4_EXPRESS
Fixes issue #10895.
Signed-off-by: Damien George <damien@micropython.org>
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM. Then in main.c use these addresses as arguments to gc_init().
The benefits of this change are:
1) When libraries are added or removed in the future changing BSS usage,
main.c's sizing of the GC heap does not need to be changed.
2) Currently these changes make the GC area about 30 KBytes larger, eg on
PICO_W the GC heap increases from 166016 to 192448 bytes. Without that
change this RAM would never get used.
3) If someone wants to disable one or more SRAM blocks on the RP2040 to
reduce power consumption it will be easy: just change the MEMORY section
in memmap_mp.ld. For instance to not use SRAM2 and SRAM3 change it to:
MEMORY
{
FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
RAM(rwx) : ORIGIN = 0x21000000, LENGTH = 128k
SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
}
Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
appropriate bits in WAKE_EN0 and SLEEP_EN0.
Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info(). Confirmed GC total size approximately matched the
size calculated by the loader.
Signed-off-by: cpottle9 <cpottle9@outlook.com>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
The device-under-test should use `multitest.expect_reboot()` to indicate
that it will reboot.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
This brings in the following new modules: hs3003, bmi270, bmm150, cbor2
and senml. It also refactors lsm6dsox and lsm9ds1.
Signed-off-by: Damien George <damien@micropython.org>
These changes allow the firmware to support both the REV-1 and REV-2
versions of the board:
- Freeze the new device drivers used in REV-2.
- Add a board-level module that abstracts the IMU chipset.
Changes are:
- Freeze micropython-lib time module to get strftime.
- Reserve the last 1MB of QSPI flash for (optional) WiFi firmware storage.
- Disable SD card mount on boot.
- Enable high-speed BLE firmware download.
This is handy when you are doing builds outside of the Git repository but
still want to record that information.
Signed-off-by: David Grayson <davidegrayson@gmail.com>
This is for boards without networking support so that the default boot.py
continues to work.
Also update boot.py to use network.country and network.hostname instead.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
