* Fix flash writes that don't end on a sector boundary. Fixes#2944
* Fix enum incompatibility with IDF.
* Fix printf output so it goes out debug UART.
* Increase stack size to 8k.
* Fix sleep of less than a tick so it doesn't crash.
If interrupts are disabled, then calling sd_* functions will hardfault.
Instead, assume that it's safe to write if interrupts are disabled.
Signed-off-by: Sean Cross <sean@xobs.io>
ARM recommends issuing a DSB instruction propr to issuing WFI, as it is
required on many parts suchas Cortex-M7. This is effectively a no-op on
the Cortex-M4 used in most NRF parts, however it ensures that we won't
be surprised when new parts come out.
See
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dai0321a/BIHICBGB.html
for more information.
Signed-off-by: Sean Cross <sean@xobs.io>
In order to ensure we don't have any outstanding requests, disable
interrupts prior to issuing `WFI`.
As part of this process, check to see if there are any pending USB
requests, and only execute the `WFI` if there is no pending data.
This fixes#2855 on NRF.
Signed-off-by: Sean Cross <sean@xobs.io>
On NRF, the `rtc_reset()` function is never called. As a result,
calls to `time.time()` return a cryptic error>
```
>>> import time
>>> time.time()
'' object has no attribute 'datetime'
>>>
```
This is because `MP_STATE_VM(rtc_time_source)` is not initialized
due to `rtc_reset()` never being called.
If `CIRCUITPY_RTC` is enabled, call `rtc_reset()` as part of the
`reset_port()` call. This ensures that `time.time()` works as expected.
Signed-off-by: Sean Cross <sean@xobs.io>
The timeout value is calculated by the common-hal layer now, so we don't
need to be quite so clever about calculating it here.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a field to allow specifying a timeout when initiating advertising.
As part of this, add a new property to determine if the device is still
advertising.
Additionally, have the `anonymous` property require a timeout, and set
the timeout to the maximum possible value if no timeout is specified.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a new parameter to the `start_advertising()` function to enable
anonymous advertising. This forces a call to `sd_ble_gap_privacy_set()`
with `privacy_mode` set to `BLE_GAP_PRIVACY_MODE_DEVICE_PRIVACY` and
`private_addr_type` set to
`BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE`.
With this, addresses will cycle at a predefined rate (currently once
every 15 minutes).
Signed-off-by: Sean Cross <sean@xobs.io>
Store the RTC value in the .uninitialized section, but make sure to
flank it with some known values. That way we can determine if the RTC
value has been initialized, or if it's random uninitialized garbage.
As part of this, add a `common_hal_rtc_init()` routine to determine if
the value is correct, or reset it to 0 if it is not valid.
Signed-off-by: Sean Cross <sean@xobs.io>
Circuit Python supports saving a single word of data across reboots.
Previously, this data was placed immediately following the .bss.
However, this appeared to not work, as Circuit Python zeroes out the
heap when it starts up, and the heap begins immediately after the .bss.
Switch to using the new .uninitialized section in order to store this
word across resets.
Signed-off-by: Sean Cross <sean@xobs.io>
Previously, it was placed following .bss. However, now that there is a
new section after .bss, the heap must be moved forward.
Signed-off-by: Sean Cross <sean@xobs.io>
This section immediately follows the .bss section, and is designed to
contain uninitialized variables that should persist across reboots.
The section is placed directly after .bss, under the theory that the
size of Circuit Python's .bss + .data is bigger than the bootloader's
.bss + .data, so there is less likely to be a conflict.
Signed-off-by: Sean Cross <sean@xobs.io>
SPIM3 is faster than all other SPI blocks, and is capable of generating
a 32 MHz clock. However, it cannot be used at the same time as the BLE
radio without dedicating an additional 8 kB of RAM to it.
Therefore, some boards may want to disable this. Support pre-defining
NRFX_SPIM3_ENABLED on the command line to disable it on some bords.
Signed-off-by: Sean Cross <sean@xobs.io>
Simmel had USB HID disabled in order to save space. However, the board
configuration did not set USB_DEVICES, causing it to inherit the default
device bouquet of MSC,CDC,MIDI,HID. This in turn caused HID to be included
in the USB Configuration Descriptor.
For some reason, this was not a problem in an earlier version of tinyusb or
circuitpython. However, in the most recent version this has rightfully
caused asserts to appear during configuration.
Re-enable USB_HID for now, as it doesn't add too much in terms of space.
We may disable it again later on if we become pressed for space.
Signed-off-by: Sean Cross <sean@xobs.io>
This was not added as part of the initial v7.0.1 patchset because
.hex files are in this project's .gitignore, and so git ignored it.
Signed-off-by: Sean Cross <sean@xobs.io>