This commit allows the user to set/get the GAP device name used by service
0x1800, characteristic 0x2a00. The usage is:
BLE.config(gap_name="myname")
print(BLE.config("gap_name"))
As part of this change the compile-time setting
MICROPY_PY_BLUETOOTH_DEFAULT_NAME is renamed to
MICROPY_PY_BLUETOOTH_DEFAULT_GAP_NAME to emphasise its link to GAP and this
new "gap_name" config value. And the default value of this for the NimBLE
bindings is changed from "PYBD" to "MPY NIMBLE" to be more generic.
This commit adds several small items to improve the support for OTA
updates on an esp32:
- a partition table for 4MB flash modules that has two OTA partitions ready
to go to do updates
- a GENERIC_OTA board that uses that partition table and that enables
automatic roll-back in the bootloader
- a new esp32.Partition.mark_app_valid_cancel_rollback() class-method to
signal that the boot is successful and should not be rolled back at the
next reset
- an automated test for doing an OTA update
- documentation updates
This commit adds full support to the unix port for Bluetooth using the
common extmod/modbluetooth Python bindings. This uses the libusb HCI
transport, which supports many common USB BT adaptors.
This commit adds an idf_heap_info(capabilities) method to the esp32 module
which returns info about the ESP-IDF heaps. It's useful to get a bit of a
picture of what's going on when code fails because ESP-IDF can't allocate
memory anymore. Includes documentation and a test.
This commit adds Loop.new_event_loop() which is used to reset the singleton
event loop. This functionality is put here instead of in Loop.close() to
make it possible to write code that is compatible with CPython.
This commit changes the esp8266 boards to use littlefs v2 as the
filesystem, rather than FAT. Since the esp8266 doesn't expose the
filesystem to the PC over USB there's no strong reason to keep it as FAT.
Littlefs is smaller in code size, is more efficient in use of flash to
store data, is resilient over power failure, and using it saves about 4k of
heap RAM, which can now be used for other things.
This is a backwards incompatible change because all existing esp8266 boards
will need to update their filesystem after installing new firmware (eg
backup old files, install firmware, restore files to new filesystem).
As part of this commit the memory layout of the default board (GENERIC) has
changed. It now allocates all 1M of memory-mapped flash to the firmware,
so the filesystem area starts at the 2M point. This is done to allow more
frozen bytecode to be stored in the 1M of memory-mapped flash. This
requires an esp8266 module with 2M or more of flash to work, so a new board
called GENERIC_1M is added which has the old memory-mapping (but still
changed to use littlefs for the filesystem).
In summary there are now 3 esp8266 board definitions:
- GENERIC_512K: for 512k modules, doesn't have a filesystem.
- GENERIC_1M: for 1M modules, 572k for firmware+frozen code, 396k for
filesystem (littlefs).
- GENERIC: for 2M (or greater) modules, 968k for firmware+frozen code,
1M+ for filesystem (littlefs), FAT driver also included in firmware for
use on, eg, external SD cards.
This commit adds micropython.heap_locked() which returns the current
lock-depth of the heap, and can be used by Python code to check if the heap
is locked or not. This new function is configured via
MICROPY_PY_MICROPYTHON_HEAP_LOCKED and is disabled by default.
This commit also changes the return value of micropython.heap_unlock() so
it returns the current lock-depth as well.
This commit changes the BLE _IRQ_SCAN_RESULT data from:
addr_type, addr, connectable, rssi, adv_data
to:
addr_type, addr, adv_type, rssi, adv_data
This allows _IRQ_SCAN_RESULT to handle all scan result types (not just
connectable and non-connectable passive scans), and to distinguish between
them using adv_type which is an integer taking values 0x00-0x04 per the BT
specification.
This is a breaking change to the API, albeit a very minor one: the existing
connectable value was a boolean and True now becomes 0x00, False becomes
0x02.
Documentation is updated and a test added.
Fixes#5738.
The default value for MICROPYPATH used in unix/main.c is
"~/.micropython/lib:/usr/lib/micropython" which has 2 problems when used in
the Windows port:
- it has a ':' as path separator but the port uses ';' so the entire string
is effectively discarded since it gets interpreted as a single path which
doesn't exist
- /usr/lib/micropython is not a valid path in a standard Windows
environment
Override the value with a suitable default.
This fix can be demonstrated by the following:
b = bytearray(32)
f = framebuf.FrameBuffer(b, 32, 8, framebuf.MONO_HLSB)
f.pixel(0, 0, 1)
print('MONO_HLSB', hex(b[0]))
b = bytearray(32)
f = framebuf.FrameBuffer(b, 32, 8, framebuf.MONO_HMSB)
f.pixel(0, 0, 1)
print('MONO_HMSB', hex(b[0]))
Outcome:
MONO_HLSB 0x80
MONO_HMSB 0x1
This adds a -h option to print the usage help text and adds a new, shorter
error message that is printed when invalid arguments are given. This
behaviour follows CPython (and other tools) more closely.
Show how to send an HTTP response code and content-type. Without the
response code Safari/iOS will fail. Without the content-type Lynx/Links
will fail.
This adds a short paragraph on how to hook readthedocs.org up. The main
goal is to make people aware of the option, to help with contributing to
the documentation.
The size of the event ringbuf was previously fixed to compile-time config
value, but it's necessary to sometimes increase this for applications that
have large characteristic buffers to read, or many events at once.
With this commit the size can be set via BLE.config(rxbuf=512), for
example. This also resizes the internal event data buffer which sets the
maximum size of incoming data passed to the event handler.
This allows the user to explicitly select the behaviour of the write to the
remote peripheral. This is needed for peripherals that have
characteristics with WRITE_NO_RESPONSE set (instead of normal WRITE). The
function's signature is now:
BLE.gattc_write(conn_handle, value_handle, data, mode=0)
mode=0 means write without response, while mode=1 means write with
response. The latter was the original behaviour so this commit is a change
in behaviour of this method, and one should specify 1 as the 4th argument
to get back the old behaviour.
In the future there could be more modes supported, such as long writes.
The address, adv payload and uuid fields of the event are pre-allocated by
modbluetooth, and reused in the IRQ handler. Simplify this and move all
storage into the `mp_obj_bluetooth_ble_t` instance.
This now allows users to hold on to a reference to these instances without
crashes, although they may be overwritten by future events. If they want
to hold onto the values longer term they need to copy them.
defindex.html (used by topindex.html) is deprecated, but topindex.html was
already identical other than setting the title, so just inherit directly
from layout.html.
Behaviour was changed from stack to queue in
8977c7eb58, and this updates variable names
to match. Also updates other references (docs, error messages).
This allows to efficiently send to an I2C slave data that is made up of
more than one buffer. Instead of needing to allocate temporary memory to
combine buffers together this new method allows to pass in a tuple or list
of buffers. The name is based on the POSIX function writev() which has
similar intentions and signature.
The reasons for taking this approach (compared to having an interface with
separate start/write/stop methods) are:
- It's a backwards compatible extension.
- It's convenient for the user.
- It's efficient because there is only one Python call, then the C code can
do everything in one go.
- It's efficient on the I2C bus because the implementation can do
everything in one go without pauses between blocks of bytes.
- It should be possible to implement this extension in all ports, for
hardware and software I2C.
Further discussion is found in issue #3482, PR #4020 and PR #4763.
It's more common to need non-blocking behaviour when reading from a UART,
rather than having a large timeout like 1000ms (the original behaviour).
With a large timeout it's 1) likely that the function will read forever if
characters keep trickling it; or 2) the function will unnecessarily wait
when characters come sporadically, eg at a REPL prompt.
This system makes it a lot easier to include external libraries as static,
native modules in MicroPython. Simply pass USER_C_MODULES (like
FROZEN_MPY_DIR) as a make parameter.
This is only correct for the extmod/uos_dupterm.c implementation however,
as e.g cc3200 implementation does the mp_load_method() itself, and anyway
requires `read` instead of `readinto`.
Replaces "PYB: soft reboot" with "MPY: soft reboot", etc.
Having a consistent prefix across ports reduces the difference between
ports, which is a general goal. And this change won't break pyboard.py
because that tool only looks for "soft reboot".
The machine.sleep() function can be misleading because it clashes with
time.sleep() which has quite different semantics. So change it to
machine.lightsleep() which shows that it is closer in behaviour to
machine.deepsleep().
Also, add an optional argument to these two sleep functions to specify a
maximum time to sleep for. This is a common operation and underlying
hardware usually has a special way of performing this operation.
The existing machine.sleep() function will remain for backwards
compatibility purposes, and it can simply be an alias for
machine.lightsleep() without arguments. The behaviour will be the same.
Examples are added to the beginning of the module docs, similarly to docs
for many other modules.
Improvements to grammar, style, and clarity. Some paragraphs are updated
with better suggestions. A warning added of the effect incorrect usage of
the module may have. Describe the fact that offset range used in one
defined structure is limited.
Otherwise there is really nothing that can be done, it can't be unlocked by
the user because there is no way to allocate memory to execute the unlock.
See issue #4205 and #4209.
With this commit there is now only one entry point into the whole
documentation, which describes the general MicroPython language, and then
from there there are links to information about specific platforms/ports.
This commit doesn't change content (almost, it does fix a few internal
links), it just reorganises things.
All concrete network classes are now moved to their own file (eg
network.WLAN.rst) and deconditionalised (remove ..only:: directives). This
makes the network documentation the same for all ports. After this change
there are no more "..only::" directives for different ports, and the only
difference among ports is the very front page of the docs.
The WiPy machine.Timer class is very different to the esp8266 and esp32
implementations which are better candidates for a general Timer class. By
moving the WiPy Timer docs to a completely separate file, under a new name
machine.TimerWiPy, it gives a clean slate to define and write the docs for
a better, general machine.Timer class. This is with the aim of eventually
providing documentation that does not have conditional parts to it,
conditional on the port.
While the new docs are being defined it makes sense to keep the WiPy docs,
since they describe its behaviour. Once the new Timer behaviour is defined
the WiPy code can be changed to match it, and then the TimerWiPy docs would
be removed.
The machine module should be standard across all ports so should have the
same set of classes in the docs. A special warning is added to the top of
the machine.SD class because it is not standardised and only available on
the cc3200 port.
It's fair to just provide a link to all available modules, regardless of
the port. Most of the existing ports (unix, stm32, esp8266, esp32) share
most of the same set of modules anyway, so no need to maintain separate
lists for them. And there's a big discussion at the start of this index
about modules not being available on a given port.
For port-specific modules, they can also be listed unconditionally because
they have headings that explicitly state they are only available on certain
ports.
The UART.init() method is now included unconditionally and its wording
adjusted to better describe ports other than the cc3200.
UART.irq() is also included unconditionally, but this is currently only
available on the WiPy target.
By virtue of its name, the pyb module would only be available on a pyboard
and so does not need to have conditional "only" directives throughout its
documentation.
These conditionals were added mostly in
cfcf47c064 in the initial development of the
cc3200 port, which had the pyb module before it switched to the machine
module. And wipy only conditionals were removed from the pyb module
documentation in 4542643025, so there's no
need to retain any more conditionals.
Allow including crypto consts based on compilation settings. Disabled by
default to reduce code size; if one wants extra code readability, can
enable them.
These can be optionally specified, but all ports are expected to be able to
accept them, at the very least ignore, though handling of "type" param
(SOCK_STREAM vs SOCK_DGRAM) is recommended.
This can be used to select the output buffer behaviour of the DAC. The
default values are chosen to retain backwards compatibility with existing
behaviour.
Thanks to @peterhinch for the initial idea to add this feature.
The parameter order in the example for ticks_diff was incorrect. If it's
"too early" that means that scheduled time is greater than current time and
if it's "running late" then scheduled time would be less than current time.
Put offset first in OR expressions, and use "offset" var instead of
hardcoded numbers. Hopefully, this will make it more self-describing
and show patterns better.
State that this doc describes generic, "core" MicroPython functionality,
any particular port may diverge in both directions, by both omitting
some functionality, and adding more, both cases described outside the
generic documentation.
Describe that the only portable way to deal with addresses is by using
getaddrinfo(). Describe that some ports may support tuple addresses using
"socket" module (vs "usocket" of native MicroPython).
This clarifies return values and the handling of invalid (e.g. newline)
characters.
Encoding conforms to RFC 3548, but decoding does not, as it ignores invalid
characters in base64 input. Instead, it conforms to MIME handling of base64
(RFC 2045).
Note that CPython doesn't document handling of invalid characters in
a2b_base64() docs:
https://docs.python.org/3/library/binascii.html#binascii.a2b_base64 , so
we specify it more explicitly than it, based on CPython's actual behavior
(with which MicroPython now compliant).
This makes top-level ToC of the pyboard docs consistent with other ports
(consisting of 3 chapters: QuickRef, General Info, and Tutorial).
Also, some other minor tweaks applied, like local ToC for General Info and
headings mentioning pyboard.
This pseudo-section causes artifacts with latexpdf generation (almost
empty page with list containing literal "genindex", "modeindex", "search"
items). For HTML docs, these sections can be accessed from "home" page.
We don't use alpha/beta/RC, so for us version and release should be the
same, or it leads to confusion (for example, current, 1.9.1 docs are
marked as 1.9 at places).
The idea is to allow to define a kind of "macros" for repeatitive text,
so all occurrances can be updated in one place. Unfortunately, RST doesn't
support replacements with arguments, which limits usefulness of them and
should be taken into account.
We have enough terms or references throughout the docs which may be not
immediately clear or have some important nuances. Referencing terms in
gloassary is the best way to deal with that.
The old intro talked about "differences", but there were hardly any
sections describing differences, mostly MicroPython specific features.
On the other hand, we now have real "differences" chapter, though it's
mostly concerned with stdlib differences.
So, try to avoid confusion by changing wording and linking to the other
chapters and contrasting them with what is described in "MicroPython
language".
Previously, only "selected chapters" were shown in left-pane ToC (of
Read The Docs theme). These chapters were selected out of order. The
rest of chapters were hidden beyond "Documentation Contents" pseudo-
chapter. This arguably led only to confusion, as many people probably
never tried to open that pseudo-chapter, and those who did, were
confused. Such organization is even worse for PDF output, causing
chapters go in mix-mashed order.
So, instead move to single clean ToC. This will allow readers of HTML
to have access to any doc content at their fingertips (and straight
before their eyes), and will allow to finally have clean PDF docs.
Move hardware-specific optimizations to the very end of document, and
add visible note that it gives an example for Pyboard. Remove references
to specific hardware technologies, so the doc can be more naturally
used across ports. Various markup updates to adhere to the latest
docs conventions.
This causes `symbol` syntax to be equivalent to :any:`symbol`, which is
in turn the easiest way to cross-reference an arbitrary symbol in the
docs:
http://www.sphinx-doc.org/en/stable/markup/inline.html#role-any
:any: requires at least Sphinx 1.3 (for reference, Ubuntu 16.03 ships
with 1.3.6, the latest 1.6.3).
Any many of our docs, `symbol` is misused to specify arguments to
functions, etc. Refactoring that is in progress. (CODECONVENTIONS
already specify proper syntax for both arguments and xrefs, based
on CPython conventions).
This adds description of implied AbstractNIC base class, which should be
"subclasses" and implemented by a particular network device class.
This is just an initial step in that direction, the API and description
will be elabotated further.
The list starts with the simplest functionality - GPIO, proceeds to
communication interfaces (UART, SPI, I2C), the to time(r) related
things, then everything else.
For a couple of ports, there was information which directory is set
as current after boot. This information doesn't belong to "uos" module,
and is moved to boards' references (which actually already contained
information on which directory is chosen for boot, even if without
explicit mentioning that it becomes current directory, which is now
done).
This method isn't implemented in any port. It seemed to have originated
in cc3200 port, but actually never was implemented there either. In
general case, it's impossible to implement this method (for example, for
a perfect GPO, which has only output latch without any feedback look
into a CPU).
Both aren't part of generic Hardware API: It's impossible to implement
.id() method in a generic case (e.g., when Pin is instantiated by the
underlying OS/RTOS). .board attribute is an obvious space hog which
instead can be implemented on Python level if needed.
MONO_xxx is much easier to read if you're not familiar with the code.
MVLSB is deprecated but kept for backwards compatibility, for the time
being.
This patch also updates the associated docs and tests.
* Fix mis-spelling of `ticks_add` in code examples.
* Be consistent about parentheses after function names.
* Be consistent about formatting of function, variable and constant names.
* Be consistent about spaces and punctuation.
* Fix some language errors (missing or wrong words, wrong word order).
* Keep line length under 90 chars.
Signed-off-by: Christopher Arndt <chris@chrisarndt.de>
User can override PYTHON executable before running script,
gen-cpydiff.py works only with Python3 and most systems register
its executable as 'python3'.
This patch introduces the a small framework to track differences between
uPy and CPython. The framework consists of:
- A set of "tests" which test for an individual feature that differs between
uPy and CPy. Each test is like a normal uPy test in the test suite, but
has a special comment at the start with some meta-data: a category (eg
syntax, core language), a human-readable description of the difference, a
cause, and a workaround. Following the meta-data there is a short code
snippet which demonstrates the difference. See tests/cpydiff directory
for the initial set of tests.
- A program (this patch) which runs all the tests (on uPy and CPy) and
generates nicely-formated .rst documenting the differences.
- Integration into the docs build so that everything is automatic, and the
differences appear in a way that is easy for users to read/reference (see
latter commits).
The idea with using this new framework is:
- When a new difference is found it's easy to write a short test for it,
along with a description, and add it to the existing ones. It's also easy
for contributors to submit tests for differences they find.
- When something is no longer different the tool will give an error and
difference can be removed (or promoted to a proper feature test).
MicroPython guarantees '/' to be a path separator, so extra constant taking
precious ROM space are not needed. MicroPython never had such constant, only
one vendor port had it (now unmaintained).
This new function controls what happens on a hard-fault:
- debugging disabled: board will do a reset
- debugging enabled: board will print registers and stack and flash LEDs
The default is disabled, ie to do a reset. This is different to previous
behaviour which flashed the LEDs and waited indefinitely.
machine.time_pulse_us() is intended to provide very fine timing, including
while working with signal bursts, where each transition is tracked in row.
Throwing and handling an exception may take too much time and "signal loss".
So instead, in case of a timeout, just return negative value. Cases of
timeout while waiting for initial signal stabilization, and during actual
timing, are recognized.
The documentation is updated accordingly, and rewritten somewhat to clarify
the function behavior.
Based on the following statistics:
$ git log docs |grep Author | sort | uniq -c | sort -n -r
175 Author: Paul Sokolovsky
135 Author: Damien George
31 Author: Daniel Campora
26 Author: danicampora
14 Author: Peter Hinch
git blame stats script from http://stackoverflow.com/a/13687302/496009:
$ sh git-authors docs
9977 author Damien George
2679 author Paul Sokolovsky
1699 author Daniel Campora
1580 author danicampora
1286 author Peter Hinch
282 author Shuning Bian
249 author Dave Hylands
Total lines per this script: 18417, my contribution is 14.5%.
