On this 32-bit arch there's no need to use the long version of the format
specifier. It's only there to appease the compiler which checks the type
of the args passed to printf. Removing the "l" saves a bit of code space.
For a given IRQn (eg UART) there's no need to carry around both a PRI and
SUBPRI value (eg IRQ_PRI_UART, IRQ_SUBPRI_UART). Instead, the IRQ_PRI_UART
value has been changed in this patch to be the encoded hardware value,
using NVIC_EncodePriority. This way the NVIC_SetPriority function can be
used directly, instead of going through HAL_NVIC_SetPriority which must do
extra processing to encode the PRI+SUBPRI.
For a priority grouping of 4 (4 bits for preempt priority, 0 bits for the
sub-priority), which is used in the stm32 port, the IRQ_PRI_xxx constants
remain unchanged in their value.
This patch also "fixes" the use of raise_irq_pri() which should be passed
the encoded value (but as mentioned above the unencoded value is the same
as the encoded value for priority grouping 4, so there was no bug from this
error).
The problem is the existing code which tries to optimise the
reinitialisation of the DMA breaks the abstraction of the HAL. For the
STM32L4 the HAL's DMA setup code maintains two private vars (ChannelIndex,
DmaBaseAddress) and updates a hardware register (CCR).
In HAL_DMA_Init(), the CCR is updated to set the direction of the DMA.
This is a problem because, when using the SD Card interface, the same DMA
channel is used in both directions, so the direction bit in the CCR must
follow that.
A quick and effective fix for the L4 is to simply call HAL_DMA_DeInit() and
HAL_DMA_Init() every time.
ADC3 is used because the H7's internal ADC channels are connected to ADC3
and the uPy driver doesn't support more than one ADC.
Only 12-bit resolution is supported because 12 is hard-coded and 14/16 bits
are not recommended on some ADC3 pins (see errata).
Values from internal ADC channels are known to give wrong values at
present.
After calling HAL_SYSTICK_Config the SysTick IRQ priority is set to 15, the
lowest priority. This commit reconfigures the IRQ priority to the desired
TICK_INT_PRIORITY value.
By default the stm module is included in the build, but a board can now
define MICROPY_PY_STM to 0 to not include this module. This reduces the
firmware by about 7k.
To use HSE bypass mode the board should define:
#define MICROPY_HW_CLK_USE_BYPASS (1)
If this is not defined, or is defined to 0, then HSE oscillator mode is
used.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI). To enable CAN on a board the mpconfigboard.h file should
define (for example):
#define MICROPY_HW_CAN1_TX (pin_B9)
#define MICROPY_HW_CAN1_RX (pin_B8)
#define MICROPY_HW_CAN2_TX (pin_B13)
#define MICROPY_HW_CAN2_RX (pin_B12)
And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
The individual union members (like SPI, I2C) are never used, only the
generic "reg" entry is. And the union names can clash with macro
definitions in the HAL so better to remove them.
The only configuration that changes with this patch is that on L4 MCUs the
clock prescaler changed from ADC_CLOCK_ASYNC_DIV2 to ADC_CLOCK_ASYNC_DIV1
for the ADCAll object. This should be ok.
A value of DISABLE for EOCSelection is invalid. This would have been
interpreted instead as ADC_EOC_SEQ_CONV, but really it should be
ADC_EOC_SINGLE_CONV for the uses in this code. So this has been fixed.
ExternalTrigConv should be ADC_SOFTWARE_START because all ADC
conversions are started by software. This is now fixed.
This can be used to select the output buffer behaviour of the DAC. The
default values are chosen to retain backwards compatibility with existing
behaviour.
Thanks to @peterhinch for the initial idea to add this feature.
