This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
This commit factors the code for files and streaming to separate source
files (vfs_fat.c and gzstream.c respectively) and introduces an abstract
gzstream interface to make it easier to plug in different filesystems.
Signed-off-by: Damien George <damien@micropython.org>
There's no need to duplicate this functionality in mboot, the code provided
in stm32lib/CMSIS does the same thing and makes it easier to support other
MCU series.
Signed-off-by: Damien George <damien@micropython.org>
The flash functions in ports/stm32/flash.c are almost identical to those in
ports/stm32/mboot/main.c, so remove the duplicated code in mboot and use
instead the main stm32 code. This also allows supporting other MCU series.
Signed-off-by: Damien George <damien@micropython.org>
In mboot, the ability to override the USB vendor/product id's was added
back in 5688c9ba09. However, when the main
firmware is turned into a DFU file the default VID/PID are used there.
pydfu.py doesn't care about this but dfu-util does and prevents its use
when the VID/PID don't match.
This commit exposes BOOTLOADER_DFU_USB_VID/PID as make variables, for use
on either command line or mpconfigboard.mk, to set VID/PID in both mboot
and DFU files.
Add -Wdouble-promotion and -Wfloat-conversion for most ports to ban out
implicit floating point conversions, and add extra Travis builds using
MICROPY_FLOAT_IMPL_FLOAT to uncover warnings which weren't found
previously. For the unix port -Wsign-comparison is added as well but only
there since only clang supports this but gcc doesn't.
A recent version of arm-none-eabi-gcc (8.2.0) will warn about unused packed
attributes in USB_WritePacket and USB_ReadPacket. This patch suppresses
such warnings for this file only.
Mboot is a custom bootloader for STM32 MCUs. It can provide a USB DFU
interface on either the FS or HS peripherals, as well as a custom I2C
bootloader interface.
