For example, the following code now works with a file on the SD card:
f = open('test', 'rb') # test must be 1024 bytes or more in size
f.seek(511)
f.read(513)
Also works for writing.
Fixes issue #1863.
The main thing is to change the DMA code in a way that the structure
DMA_Stream_TypeDef (which is similar to DMA_Channel_TypeDef on stm32l4)
is no longer used outside of dma.c, as this structure only exists for the
F4 series. Therefore I introduced a new structure (dma_descr_t) which
handles all DMA specific stuff for configuration. Further the periphery
(spi, i2c, sdcard, dac) does not need to know the internals of the dma.
A standard I2C address is 7 bits but addresses 0b0000xxx and 0b1111xxx
are reserved. The scan() method is changed to reflect this, along with
the docs.
The L4 MCU supports 40 Events/IRQs lines of the type configurable and
direct. But this L4 port only supports configurable line types which are
already supported by uPy. For details see page 330 of RM0351, Rev 1.
The USB_FS_WAKUP event is a direct type and there is no support for it.
__GPIOI_CLK_ENABLE is defined in hal/l4/inc/Legacy/stm32_hal_legacy.h
as __HAL_RCC_GPIOI_CLK_ENABLE, and that latter macro is not defined
anywhere else (because the L4 does not have port GPIOI). So the test
for GPIOI is needed, along with the test for the CLK_ENABLE macro.
L4 does not have UART6, and has similar registers to the F7.
Original patch was authored by Tobias Badertscher / @tobbad, but it was
reworked to split UART edits from USB edits.
64-bit integer division brings a dependency on library functions. It is
avoided here by dividing fck and baud by a common divisior. The error
is the better (1/(2*0x300)) as with 64 bit division (1/(0x300)).
These files come from STM32Cube_FW_L4_V1.3.0, with Windows line endings
converted to unix. Only basic HAL files are added. In addition the QSPI
support is included to support later external QSPI flash as mass storage.
- add template rule that converts a specified source file into a qstring file
- add special rule for generating a central header that contains all
extracted/autogenerated strings - defined by QSTR_DEFS_COLLECTED
variable. Each platform appends a list of sources that may contain
qstrings into a new build variable: SRC_QSTR. Any autogenerated
prerequisities are should be appened to SRC_QSTR_AUTO_DEPS variable.
- remove most qstrings from py/qstrdefs, keep only qstrings that
contain special characters - these cannot be easily detected in the
sources without additional annotations
- remove most manual qstrdefs, use qstrdef autogen for: py, cc3200,
stmhal, teensy, unix, windows, pic16bit:
- remove all micropython generic qstrdefs except for the special strings that contain special characters (e.g. /,+,<,> etc.)
- remove all port specific qstrdefs except for special strings
- append sources for qstr generation in platform makefiles (SRC_QSTR)
The config variable MICROPY_MODULE_FROZEN is now made of two separate
parts: MICROPY_MODULE_FROZEN_STR and MICROPY_MODULE_FROZEN_MPY. This
allows to have none, either or both of frozen strings and frozen mpy
files (aka frozen bytecode).
tools/pydfu.py is now the recommended way of deploying a DFU file. Old
behaviour of dfu-util can be obtained by passing USE_PYDFU=0 when invoking
make.
The main README.md file has been updated to reflect this change.
If None was returned for such requests (which likely means that user simply
didn't handle them), it means successful init and default sector size of 512
bytes respectively. This makes only BP_IOCTL_SEC_COUNT a mandatory request,
and thus re-establishes parity with old interface, where only .count() is
mandatory().
This patch adds support to fsusermount for multiple block devices
(instead of just one). The maximum allowed is fixed at compile time by
the size of the fs_user_mount array accessed via MP_STATE_PORT, which
in turn is set by MICROPY_FATFS_VOLUMES.
With this patch, stmhal (which is still tightly coupled to fsusermount)
is also modified to support mounting multiple devices And the flash and
SD card are now just two block devices that are mounted at start up if
they exist (and they have special native code to make them more
efficient).
You can now create (singleton) objects representing the flash and SD
card, using:
flash = pyb.Flash()
sdcard = pyb.SDCard()
These objects provide the block protocol.
This enables MICROPY_HW_HAS_FLASH which got missed.
The HW has UART2 on the 401 connected to the STLINK procesor
which exposes it as USB serial. This connects that up so that
you can get a REPL using the USB serial.
If MICROPY_FATFS_MAX_SS is defined to power of 2 value between 1024 and
4096, support for dynamic sector size in FatFs will be enabled. Note
that FatFs reserves static buffer of MICROPY_FATFS_MAX_SS size for each
filesystem in use, so that value should be set sparingly.
Initial patch provided by @pfalcon.
The new block protocol is:
- readblocks(self, n, buf)
- writeblocks(self, n, buf)
- ioctl(self, cmd, arg)
The new ioctl method handles the old sync and count methods, as well as
a new "get sector size" method.
The old protocol is still supported, and used if the device doesn't have
the ioctl method.
Per the previously discussed plan. mount() still stays backward-compatible,
and new mkfs() is rought and takes more args than needed. But is a step
in a forward direction.
If MICROPY_VFS_FAT is defined, mp_type_fileio & mp_type_textio won't be
defined, as these may be alredy defined elsewhere. The idea is to have
compartmentalized VFS FatFs class, which can work in parallel with some
other "main" filesystem. E.g., for unix port, mp_type_fileio, etc. will
be defined for the main POSIX filesystem, while stmhal/file.c will be
a self-contained VFS file class.
Move definition of mp_builtin_open_obj to a separate module, then file.c
becomes more or less compartmentalized FatFs file class, which can be used
together with file class implementations for other (V)FSes.
For these 3 bitwise operations there are now fast functions for
positive-only arguments, and general functions for arbitrary sign
arguments (the fast functions are the existing implementation).
By default the fast functions are not used (to save space) and instead
the general functions are used for all operations.
Enable MICROPY_OPT_MPZ_BITWISE to use the fast functions for positive
arguments.
Previous to this patch the DMA was setup and then the I2C address sent.
If the I2C address sending failed (eg no I2C device on the bus) then the
DMA was left in an inconsistent state.
This patch moves the DMA setup to after a successful sending of the I2C
address(es).
See issue #1765.
USB CDC no longer needs TIM3 (which was originally used for LED(4) PWM)
and so TIM3 has been freed for general purpose use by the user. Hence
LED(4) lost its PWM capabilities.
This patch reinstates the PWM capabilities using a semi-generic piece
of code which allows to configure a timer and PWM channel to use for any
LED. But the PWM capability is only configured if the LED is set to an
intensity between 1 and 254 (ie only when needed). In that case the
relevant timer is configured for PWM. It's up to the user to make sure
the timers are not used if PWM is active.
This patch also makes sure that PWM LEDs are turned off using standard
GPIO when calling led.off() or led.intensity(0), instead of just setting
the PWM counter to zero.
TIM3 is no longer used by USB CDC for triggering outgoing data, so we
can now make it available to the user.
PWM fading on LED(4) is now gone, but will be reinstated in a new way.
Previous to this patch the USB CDC driver used TIM3 to trigger the
sending of outgoing data over USB serial. This patch changes the
behaviour so that the USB SOF interrupt is used to trigger the processing
of the sending. This reduces latency and increases bandwidth of outgoing
data.
Thanks to Martin Fischer, aka @hoihu, for the idea and initial prototype.
See PR #1713.
Calling it from mp_init() is too late for some ports (like Unix), and leads
to incomplete stack frame being captured, with following GC issues. So, now
each port should call mp_stack_ctrl_init() on its own, ASAP after startup,
and taking special precautions so it really was called before stack variables
get allocated (because if such variable with a pointer is missed, it may lead
to over-collecting (typical symptom is segfaulting)).
Functions added are:
- randint
- randrange
- choice
- random
- uniform
They are enabled with configuration variable
MICROPY_PY_URANDOM_EXTRA_FUNCS, which is disabled by default. It is
enabled for unix coverage build and stmhal.
This allows FROZEN_DIR=some-directory to be specified on the make
command line, which will then add all of the files contained within
the indicated frozen directory as frozen files in the image.
There is no change in flash/ram usage if not using the feature.
This is especially useful on smaller MCUs (like the 401) which only
has 64K flash file system.
Seedable and reproducible pseudo-random number generator. Implemented
functions are getrandbits(n) (n <= 32) and seed().
The algorithm used is Yasmarang by Ilya Levin:
http://www.literatecode.com/yasmarang
The first argument to the type.make_new method is naturally a uPy type,
and all uses of this argument cast it directly to a pointer to a type
structure. So it makes sense to just have it a pointer to a type from
the very beginning (and a const pointer at that). This patch makes
such a change, and removes all unnecessary casting to/from mp_obj_t.
Adds a lot of code, makes IRQs a bit less efficient, but is very useful
for debugging. Usage: pyb.irq_stats() returns a memory view that can be
read and written, eg:
list(pyb.irq_stats())
pyb.irq_stats()[0]
pyb.irq_stats()[0] = 0
The patch provides general IRQ_ENTER() and IRQ_EXIT() macros that can be
modified to provide further IRQ statistics if desired.
To let unix port implement "machine" functionality on Python level, and
keep consistent naming in other ports (baremetal ports will use magic
module "symlinking" to still load it on "import machine").
Fixes#1701.
Similar to recently added feature in unix port: if event triggers for an
objects, its polling flags are automatically reset, so it won't be polled
until they are set again explicitly.
Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx
to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI
and NSS. This makes it the same as how I2C is configured.
This is refactoring to enable support for the two USB PHYs available on
some STM32F4 processors to be used at the same time. The F405/7 & F429
have two USB PHYs, others such as the F411 only have one PHY.
This has been tested separately on a pyb10 (USB_FS PHY) and F429DISC
(USB_HS PHY) to be able to invoke a REPL/USB. I have modified a PYBV10
to support two PHYs.
The long term objective is to support a 2nd USB PHY to be brought up as a
USB HOST, and possibly a single USB PHY to be OTG.
Currently nlr_jump_fail prints that there was an uncaught exception
but nothing about the exception.
This patch causes nlr_jump_failed to try to print the exception.
Given that printf was called on the line above, I think that
the call to mp_obj_print_exception has about as much likelyhood
of succeeding as the printf does.
When you use the USER button to perform a filesystem reset
at boot time then it wipes out the filesystem and creates
a new boot.py and main.py. With this patch these files are
executed after formatting, ensuring that pyb and machine modules
get imported.
This is a hack to free up TIM3 so that it can be used by the user.
Instead we use the PVD irq to call the USB VCP polling function, and
trigger it from SysTick (so SysTick itself does not do any processing).
The feature is enabled for pyboard lite only, since it lacks timers.
Consider the following scenario: SD card is being read by pyboard; USB
irq comes in for MSC read request; SD card needs to be read from within
USB irq while SD read is already ongoing. Such contention needs to be
avoided.
This patch provides a simple solution, to raise the irq priority above
that of the USB irq during SD DMA transfers. Pyboard and PC can now
read from the SD card at the same time (well, reads are interleaved).
In non-blocking mode (timeout=0), uart.write() can now transmit all of its
data without raising an exception. uart.read() also works correctly in
this mode.
As part of this patch, timout_char now has a minimum value which is long
enough to transfer 1 character.
Addresses issue #1533.
With these you can now do things like:
stm.mem32[0x20000000] = 0x80000000
and read 32-bit values. You can also read all the way to the end
of memory using either stm.mem32[0xfffffffc] or stm.mem32[-4].
IRQs shouldn't use mem32 at all since they'd fail if the top 2 bits
weren't equal, so IRQs should be using 16-bit I/O.
The STMCube examples define both USE_USB_HS and USE_USB_HS_IN_FS when they
use the HS in FS mode.
The STM32F401 doesn't have a USB_HS at all, so the USB_OTG_HS instance
doesn't even exist.
The UARTs have no FIFOs, so if interrupts are disabled
for more than a character time (10 usec at 1 Mbit/sec)
then characters get dropped.
The overhead for handling a UART ISR is about 0.5 usec,
so even at baud rates of 1 Mbit/sec this only corresponds
to about 5% of the CPU. Lower baud rates will have less
of an impact.
uwTick can only change in the SysTick IRQ so this IRQ function does not
need to take special care with this variable. It's important to make
this IRQ function as efficient as possible.
Using SysTick to do the counting and dispatch of the flash storage idle
handler is more efficient than requiring a dedicated hardware timer.
No new counter is needed, just the existing uwTick variable. The
processing is not actually done in the SysTick IRQ, it is deferred to
the flash IRQ (which runs at lower priority).
