They are now efficient (in runtime performance) and provide a useful
feature that's hard to obtain without them enabled.
See issue #3644 and PR #3826 for background.
This patch makes it so that UART(0) can by dynamically attached to and
detached from the REPL by using the uos.dupterm function. Since WebREPL
uses dupterm slot 0 the UART uses dupterm slot 1 (a slot which is newly
introduced by this patch). UART(0) must now be attached manually in
boot.py (or otherwise) and inisetup.py is changed to provide code to do
this. For example, to attach use:
import uos, machine
uart = machine.UART(0, 115200)
uos.dupterm(uart, 1)
and to detach use:
uos.dupterm(None, 1)
When attached, all incoming chars on UART(0) go straight to stdin so
uart.read() will always return None. Use sys.stdin.read() if it's needed
to read characters from the UART(0) while it's also used for the REPL (or
detach, read, then reattach). When detached the UART(0) can be used for
other purposes.
If there are no objects in any of the dupterm slots when the REPL is
started (on hard or soft reset) then UART(0) is automatically attached.
Without this, the only way to recover a board without a REPL would be to
completely erase and reflash (which would install the default boot.py which
attaches the REPL).
Disabling this saves around 6000 bytes of code space and gets the 512k
build fitting in the available flash again (it increased lately due to an
increase in the size of the ESP8266 SDK).
Certain pins (eg 4 and 5) seem to behave differently at the hardware level
when in open-drain mode: they glitch when set "high" and drive the pin
active high for a brief period before disabling the output driver. To work
around this make the pin an input to let it float high.
This patch takes the software SPI implementation from extmod/machine_spi.c
and moves it to a dedicated file in drivers/bus/softspi.c. This allows the
SPI driver to be used independently of the uPy runtime, making it a more
general component.
The PWM at full value was not considered as an "active" channel so if no
other channel was used the timer used to mange PWM was not started. So
when another duty value was set the PWM timer restarted and there was a
visible glitch when driving LEDs. Such a glitch can be seen with the
following code (assuming active-low LED on pin 0):
p = machine.PWM(machine.Pin(0))
p.duty(1023) # full width, LED is off
p.duty(1022) # LED flashes brightly then goes dim
This patch fixes the glitch.
These were copied from the stm32 port (then stmhal) at the very beginning
of this port, with the anticipation that the esp8266 port would have board
definition files with a list of valid pins and their names. But that has
not been implemented and likely won't be, so remove the corresponding lines
from the Makefile.
Because otherwise the function can return with data still waiting to be
clocked out, and CS might then be disabled before the SPI transaction is
complete. Fixes issue #3487.
Prior to this fix, enabling WebREPL for the first time via webrepl_setup
did not work at all because "boot.py" did not contain any lines with
"webrepl" in them that could be uncommented.
This patch simplifies the str creation API to favour the common case of
creating a str object that is not forced to be interned. To force
interning of a new str the new mp_obj_new_str_via_qstr function is added,
and should only be used if warranted.
Apart from simplifying the mp_obj_new_str function (and making it have the
same signature as mp_obj_new_bytes), this patch also reduces code size by a
bit (-16 bytes for bare-arm and roughly -40 bytes on the bare-metal archs).
Recent vendor SDKs ship libs with code in .text section, which previously
was going into .irom0.text. Adjust the linker script to route these
sections back to iROM (follows upstream change).
Macros to convert big-endian values to host byte order and vice-versa.
These were defined in adhoc way for some ports (e.g. esp8266), allow
reuse, provide default implementations, while allow ports to override.
In the vendor SDK 2.1.0, some of the functions which previously didn't
have prototypes, finally acquired them. Change prototypes on our side
to match those in vendor headers, to avoid warnings-as-errors.
The uos.dupterm() signature and behaviour is updated to reflect the latest
enhancements in the docs. It has minor backwards incompatibility in that
it no longer accepts zero arguments.
The dupterm_rx helper function is moved from esp8266 to extmod and
generalised to support multiple dupterm slots.
A port can specify multiple slots by defining the MICROPY_PY_OS_DUPTERM
config macro to an integer, being the number of slots it wants to have;
0 means to disable the dupterm feature altogether.
The unix and esp8266 ports are updated to work with the new interface and
are otherwise unchanged with respect to functionality.
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
Damien George
Lars Kellogg-Stedman
Olivier Ortigues
Paul Sokolovsky
Vitor Massaru Iha